• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.4
• /
• pp.341-348
• /
• 2019

In this study, we analyzed the problems of existing construction waste shredding technology to diagnose the problems of low quality recycled aggregates and to develop a new mortar peeling technique to produce high-quality recycled coarse aggregate for concrete. The purpose of this study is to verify the effectiveness of mortar peeling technique by doing simulation prior to on-site application and to check the quality properties of recycled coarse aggregate produced by applying a mortar peeling technique. We manufactured and installed High speed Rotating Grinder on-site and analyzed the correlation between mortar adhesion amount, dry density and water absorption rate of recycled coarse aggregate.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.4
• /
• pp.145-151
• /
• 2019

The Physical performance of use materials was evaluated to improve durability of fast-paced repair mortar used at rapid construction sites. The fastening performance and basic performance were evaluated by substituting ferronickel grinding slag residues, rapid settlement, and EVA-based polymer for mortar. As a result, the compressive strength, flexural strength and adhesion strength were increased due to the use of FS Fine Aggregate and RS Fine Aggregate. The chloride ion promotion test of fast-polymer mortar kept the chloride inhibitory performance from 7 days to 28 days when fNS was used less than 50%. Durability degradation due to the use of FS Fine Aggregate and RS Fine Aggregate has not been found, and it is believed that further consideration of economic and long-term durability will be required for use as alternative Aggregate for construction and civil engineering.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.5
• /
• pp.391-399
• /
• 2019

This study reviewed the possibility of recycling into exhausted aggregate resources in Korea as a means of utilizing coal gasification slag(CGS) from integrated gasification combined cycle(IGCC) while being commissioned in order to introduce the new system to Korea. In other words, in order to solve the problem of insufficient aggregate resources, CGS generated by IGCC as a residual aggregate for concrete secondary products, which is an empty mortar, was considered to replace CGS in the range of 0 to 100 % for mixed residual aggregate mixed with crushed sand A(CSa) of good quality and sea sand(SS) of deep particles, which are the most commonly used in the domestic construction industry. According to the study, replacing CGS with CSa or crushed sand B(CSb)+SS by 25 % to 50 % resulted in good results in the aspect of the granularity of the aggregate and the workability and compressive strength of cement mortar, which were found to be usable.

• Cement Symposium
• /
• no.32
• /
• pp.222-227
• /
• 2005

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.4
• /
• pp.374-381
• /
• 2015

This study is investigating the fire resistant finishing materials composed of fly ash and glass forming light weight aggregate has the high temperature thermal stability. High temperatures such as a fire, cementitious materials beget dehydration and micro crack of cement matrix. From the test result, developed fire resistant finishing materials showed good stability in high temperatures. These high temperature stability is caused by the ceramic binding and low thermal conductivity of glass forming light weight aggregate. Also, alkali activation reaction of fly ash and meta kaolin not showing the decomposition of calcium hydrates. Thus, this result indicates that it is possible to fire resistant finishing light weight mortars.

• Journal of the Korea Concrete Institute
• /
• v.21 no.2
• /
• pp.147-152
• /
• 2009

The compressive strength test, bulk density and mortar absorption ratio were carried out to utilize the data as the basic sources for the lightweight mortar and the lightweight concrete, through the study on the physical characteristics of the artificial lightweight aggregate (ALA) made of waste glasses, which was developed for the first time in the country. On the basis of these experiments, the density and the unit volume weight of the ALA showed the value less than 50% of the common aggregate due to the independent pore structure, and the mortar that contains ALA had no big difference from the Control mortar in the test of the absorption ratio. It is judged that this happens based on the internal independent pore structure of the ALA. In case of the mortar containing ALA, there was a tendency of declination in the compressive strength and the bending strength as the mixing rate is increasing, but all mortar showed more than 70% of the Control mortar compressive strength except for the La50 mortar. Hereafter, it is judged that according to the control of the mixing ratio of mineral admixing agent, water and cement, it will realize the equal strength to the control mortar, and the long term edurance is needed to be considered together.

• The Journal of Engineering Geology
• /
• v.13 no.3
• /
• pp.309-320
• /
• 2003

Since the concrete covers most structures in modern architecture and it is composed of aggregates of about 75%, the appropriate selection of aggregates is valuable for the durability of concrete. A major cause of the expansion of mortar-bar measured by ASTM C 227-90 has been accounted by the alkali-aggregate reaction. This study carried out designed experiments on some aggregates including basalt and sandstone, to classify the expansion factors into the alkali-aggregate reaction, the increase of the gel pore volume, and the interstitial water that could expand physically the cracks or foliation developed in aggregates itself. The quantitative analyses of expansion by each factor indicated that the interstitial water and/or the alkali-aggregate reaction had major roles in the concrete expansion. Thus, if the supplied aggregates have deteriorated the structural framework, it is important to investigate the exact causes through this suggested method.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.2
• /
• pp.97-104
• /
• 2023

In order to maximize the utilization of recycled fine aggregate, high strength mortar made of 100 % recycled fine aggregate was prepared, and its physical properties were evaluated to determine the possibility of using recycled fine aggregate as structural aggregate. The effect caused by the amount of nanosilica on the physical properties of w/b 0.2 recycled fine aggregate mortar consisting of cement, silica fume, and blast furnace slag. To improve the dispersion of nanosilica inside mortar, an aqueously dispersed nanosilica solution by ultrasonic tip sonication was prepared, and incorporated into the mortar to evaluate changes in mortar flow, porosity and compressive strength depending on nanosilica content. According to the experimental results, mortar flow decreased as the replacement ratio of nano-silica increased. As the replacement ratio of nanosilica increased up to 0.75 %, the porosity decreased and the compressive strength increased, but, at a replacement ratio of 1 %, the porosity increased and the compressive strength decreased. It was confirmed that the nano-silica replacement ratio of 0.75 % was optimum proportion to maximize the mechanical performance of high-strength recycled fine aggregate mortar.

• Journal of the Korea Institute of Building Construction
• /
• v.18 no.3
• /
• pp.219-225
• /
• 2018

The aim of the research is improving the quality of concrete by using the alternative aggregate resources and recycling wastes. To make a combined aggregate fitted in standard particle size distribution curve, crushed sand from blasted rock debris was used as a base aggregate. Additionally, to increase the portion of fine particles, sea sand was mixed. Although these aggregate combination fit the standard particle size distribution curve, in this research, raw coal ash was replaced as a microfine. According to the experiment, by replacing 5% raw coal ash, the most favorable results were achieved in aggregate gradation and cement mortar quality.

• The Journal of Engineering Geology
• /
• v.6 no.3
• /
• pp.155-163
• /
• 1996

The current ASTM C227-90 is a prescription on the mortar-bar method. This recornrnends that mortar-bars should be made using a mixing ratio by weight of 675 grams aggregate to 300 grams cement, and their initial lengths should be measured in $24{\pm}2$ hours. This method emphasizes that the prepare sample mortar-bars and calculate expansion rates of them. This method requires constant G values (effective gauge lengths) of denominator in the calculation formula, which are fixed either at 10 inches or 250mm. This study, based on experimental approaches, reexamines the suggestions made by those two prescriptions above and important results are summarized in the following. 1. Not only alkali-aggregate reaction but also interaction of interstitial and gel water are responsible for expansion of mortar-bars. This requires partial modification of the current ASTM C227-90. 2. A mixing ratio by volume rather than by weight of aggregate to cement is recommendable for measuring the amount of expansion resulting from alkali-aggregate reaction and from interstitial water. 3. The method of when to measure initial lengths and how to calculate expansion rate suggested by ASThI C227-90 and Cl90-93a should partly be modified for more accurate results.