• Geophysics and Geophysical Exploration
• /
• v.14 no.2
• /
• pp.146-151
• /
• 2011

A method to evaluate and to reduce the source- and receiver- consistent noise in a cross-well travel time data was proposed. These systematic noises, which can cause some serious effects on the result of a travel time tomography, can be considered as the source and receiver statics. The method evaluates the statics through a curve-fitting of the first arrival travel times in the common source and common receiver gathers. Feasibility study was conducted on a synthetic data which simulates the cross-well travel time tomography to detect a small scale tunnel in a uniform background medium. First arrival travel times at a given source and receiver points are computed by a raytracing method, and the source consistent- and receiver consistent noises are added to the record. In case of the added noise with rms amounting to 25% of the maximum expected anomalous travel time delays, it is confirmed that the method successfully extracted the noise at the 7th step of iteration.

• Applied Chemistry for Engineering
• /
• v.8 no.3
• /
• pp.403-409
• /
• 1997

The equilibrium constants of five deoxyribonucleosides (dDyd, dUrd, dGuo, dThd, dAdo) were estimated by the plate theory and the moment method under isocratic conditions of the Reversed-Phase High Performance Liquid Chromatography (RP-HPLC). The mobile phase in this system was composed of water and organic modifiers(acetonitrile and methanol) The plate theory of linear adsorption isotherm was treated on the basis of continuous flow of eluent through the plates of the column. The moment method was utilized to find the equilibrium constant from the first absolute moment of experimental data. The equilibrium constants of five deoxyribonucleosides in the two methods were very close, and also the equilibrium constants calculated by capacity factor were similar to those by both the plate theory and the moment method. The equilibrium constant was expressed as a semi-log function of the quantity of organic modifier. Excellent agreements between the calculated elusion profile by the plate theory and the experimental data were observed.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.8
• /
• pp.238-244
• /
• 2013

In energy dispersive X-ray fluorescence analysis, the removal of the continuum on which the X-ray spectrum is superimposed is one of the most important processes, since it has a strong influence on the analysis result. The existing methods which have been used for it usually require tight constraints or prior information on the continuum. In this paper, an efficient background correction method is proposed for Energy Dispersive X-ray fluorescence (EDXRF) spectra. The proposed method has two steps of background modeling and background correction. It is based on the basic concept which differentiates background areas from the peak areas in a spectrum and the SNIP algorithm, one of the popular methods for background removal, is used to enhance the performance. After detecting some points which belong to the background from a spectrum, its background is modeled by a curve fitting method based on them. And then the obtained background model is subtracted from the raw spectrum. The method has been shown to give better results than some of traditional methods, while working under relatively weak constraints or prior information.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.3
• /
• pp.1-8
• /
• 2001

Seismic design forces for bridge components may be determined by modifying elastic member forces of design earthquakes using appropriate response modification factors according to the national design code of bridges Modeling technique of pile foundation system is one of the important parameters which greatly affects the results in the process of the elastic seismic analysis of a bridge system with pile foundation. In this paper, a approximate and simplified modeling technique of a pile foundation system for the practical purposes is presented. The modeling technique is based on the stiffnesses of pile foundation during earthquake. The horizontal stiffnesses are determined from the resistance-deflection curves derived from the results of dynamic field tests using cyclic loads and the vertical stiffness includes the effects of the end bearing capacities and side friction of piles as well as the pile compliances under the expected vertical load level. The applicability of the proposed technique has been validated through the some example bridge analyses.

• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.1-7
• /
• 2003

We determined the optical constants of organic light emitting material of Alq$_3$ in a spectral range between 1.5 and 6 eV using the physical model introduced by Forouhi and Bloomer［Phys. Rev. B 34, pp. 7018-7026, 1986.］. The initial parameters of $A_i,\;B_i,\;C_i$ of Forouhi-Bloomer dispersion relations were determined from the absorption peaks and widths of absorption spectra of the Alq$_3$ film. The refractive index of substrate, a fused silica, is derived from the Sellmeier equation with the measured transmittance and reflectance spectra. Then, the complex refractive index and thickness of the Alq$_3$ film were calculated by use of a nonlinear least square fitting program with the Forouhi-Bloomer dispersion relation and the measured transmittance and reflectance spectra.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.4
• /
• pp.459-468
• /
• 2014

An additional relationship equation is numerically obtained to increase the accuracy of the conventional equation for obtaining the resonant frequency of a resonator. Although the conventional equation is widely used in industry because of its simplicity, it does not provide enough information on the cavity or the neck of the resonator for noise reduction in a duct. Resonator designers have difficulty implementing resonator design owing to the uncertainty in geometry presented by the well-known formula for determining the resonant frequency. To overcome this problem, this work determines an approximate equation using results of numerical calculation. To this end, shape parameters of the neck and cavity of a resonator are defined, and an equation describing the relationship between them is derived by adjusting the peak frequency in the transmission loss curve of a resonator to its resonant frequency. The application and validity of the derived equation are investigated in a numerical simulation and an acoustic experiment, respectively.

• Water for future
• /
• v.19 no.2
• /
• pp.149-156
• /
• 1986

The generated sequences of monthly flows were analyzed based on the range concept. With the optimum operation rule of the reservoirs as the one which maximizes the wateruse downstream the waterrelease from the reservoir was determined and with \ulcorner consideration to the mean inflows and the range of monthly flows the required reservoirs capacity was stochastically determind. It is suggested that the result obtained in this study would be applied to approximately estimate, in the stage of preliminary design, the required capacity of a reservoir in question with the limited information such as the mean monthly inflow and the period of reservoir operation. For the determination of a reservoir capacity Rippl's mass-curve method has been long used with the past river flow data assuming the same flow records will be repeated in the future. This study aims to find out a better method for determining the reservoir capacity by employing the analytical theory based on the stochastic process. For the present study the synthetic generation methods of Thomas-Fiering type was used to synthetically generate 50 years of monthly river inflows to three single-purpose reservoirs and three multi-purpose reservoirs.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.2 no.4
• /
• pp.208-222
• /
• 1990

The nonlinear hydrodynamic pressure force and moment on hinged wavemakers of variable-draft are presented. A closed-form solution (correct to second-order) for the nonlinear wavemaker boundary value problem has been obtained by employing the Stokes perturbation expansion scheme. The physical significance of the second-order contributions to the hydrodynamic pressure moment are examined in detail. Design curves are presented which demonstrate both the magnitude of the second-order nonlinearities and the effects of the variable-draft hinge height. The second-order contributions to the total hydrodynamic force and moment consist of a time-dependent and a steady part. The sum of the first and second-order pressure force and moment show a significant increase over those predicted by linear wavemaker theory. The second-order effects are shown to vary with both relative water depth and wave amplitude. The second-order dynamic effects are relatively more important for hinged wavemakers with shallower drafts.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.4
• /
• pp.390-402
• /
• 1997

The ignition noises from the vehicle are measured and the measurement data are statistically treated for modeling. The low-noise amplifier and band-pass filter are added between the receiver and the three axes antenna for low noise level measurement and the APD and PSD are measured in 800 MHz frequency range. The measured APD curves can be expressed in terms of sensitivity study of each model through 3(class A) or 6(Class B) parameters variation, and these optimal parameter can easily be calculated by using the Composite Approximation Algorithm. The selected APD parameter can be used for making the Data Base EM-environments and also applied to determine the output and sensitivity margin for the transmitter and receiver. 'Digital microwave transmission systems are equipped with equalizer against fading during multipath fading. In this paper, we proposed variable reference tap position equalizer that varies the reference tap according to fading type to archive better performance. We got the perf？mance improvement about 4~5 dB in MP condition and 2~3 dB in NMP condition from simulation results.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.15 no.4
• /
• pp.400-405
• /
• 2005

This paper analyzes the performance of a face recognition algorithm using the eigenfaces method. In the absence of robust personal recognition schemes, a biometric recognition system has essentially researched to improve their shortcomings. A face recognition system in biometries is widely researched in the field of computer vision and pattern recognition, since it is possible to comprehend intuitively our faces. The proposed system projects facial images onto a feature space that effectively expresses the significant variations among known facial images. The significant features are known as 'eigenfaces', because they are the eigenvectors(principal components) of the set of faces. The projection operation characterizes an individual face by a weighted sum of the eigenface features, and to recognize a particular face it is necessary only to compare these weights to those of known individuals. In order to analyze the performance of the system, we develop a face recognition system by using Harvard database in Harvard Robotics Laboratory. We present the recognition rate according to variations on the lighting condition, numbers of the employed eigenfaces, and existence of a pre-processing step. Finally, we construct a rejection curve in order to investigate the practicability of the recognition method using the eigenfaces.