• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1995.11a
• /
• pp.23-26
• /
• 1995

내경 0.1 m, 높이 5.3 m 의 순환유동층 반응기를 사용하여 기체의 역혼합특성을 조사하였다. 기체의 역혼합은 동일한 기상유속일때 고체순환속도가 증가할수록 증가하였다. 희박상영역에서 일정한 고체체류량에서는 기상유속이 증가할수록 벽면에서의 하강흐름도 증가되어 기체의 역혼합은 증가되었다. Tracer 주입위치가 반응기 벽면에서 중심으로 이동할수록 빠른 기체와 고체의 흐름으로 인하여 기체의 역혼합은 상당히 감소하였다. 그리고, 희박상영역에서 core-annulus 구조를 기초로 하여 기체역혼합과 core 와 annulus 간의 물질전달계수를 예측할 수 있는 모델식을 제안하였다.

• Clean Technology
• /
• v.17 no.1
• /
• pp.62-68
• /
• 2011

Hydrodynamic characteristics in multistage annular type fluidized bed (riser: $0.01{\times}0.025{\times}2.8m^3$, J-valve: $0.009{\times}0.015m^2$)were investigated. Glass beads ($d_p=101{\mu}m$, ${\rho}_b=1,590kg/m^3$, $U_{mf}=1.25{\times}10^{-2}m/s$, Geldart classification B) was used as a bed material. Accumulated weight by the electronic balance was measured to determine the solid flow rate in batch-type. In circulation condition, we measured the accumulated weight of particle transported from riser. At the steady state condition, solid circulation rate was calculated from time interval of the heated bed material passing between two thermocouples. Solid flow rate increased with increasing inlet gas velocity ($1.2-2.6U_{mf}$) and the static bed height (z, 0.24-0.68 m) from 2.2 to 23.4 kg/s. However, mean residence time decreased with increasing inlet gas velocity ($1.2-2.6U_{mf}$) and the static bed height (z, 0.24-0.68 m) from 1,438 to 440 s. The solid holdup in the riser was determined by measuring pressure differences according to the riser height. These results showed a similar trend to that of simple exponential decay type except for the top section of the riser. To verify the gas bypassing from top bubbling beds to middle bubbling beds, $CO_2$ gas was injected by tracer gas in constant ratio, and then was measured $CO_2$ concentration in outlet gas by gas chromatography. Gas bypassing occurred below 2.6% which is negligible value.

• Korean Chemical Engineering Research
• /
• v.48 no.2
• /
• pp.198-204
• /
• 2010

Solids flow characteristics have been determined in a pressurized solids recycle systems of silica sand particles for the application in a pressurized CFB(PCFB). The solids recycle system is composed of a downcomer(0.10 m i.d. 2.25 m high) and a loop-seal(0.10 m i.d.). The silica sand($d_p=240{\mu}m$, ${\rho}_s=2582kg/m^3$) particles were transported at room temperature and system pressure($P_{sys}$) up to 0.71 MPa using air. Solids mass flux($G_s$) increases with increasing system pressure at constant aeration rate. Pressure gradient, solids velocity and actual gas velocity increase with increasing $P_{sys}$ at constant aeration rate. The Pressure drop number($\Phi$) on pressure gradient in downcomer has been correlated with Transportation number(Tr). Pressure drop across the loop-seal increases with increasing of $G_s$ irrespective of variation of $P_{sys}$. The obtained $G_s$ and Transportation number(Tr) have been correlated with the experimental variables.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1998.05a
• /
• pp.27-30
• /
• 1998

지난 수십 년간 순환유동층과 riser 반응기에 관한 연구는 상당한 진전을 이뤄왔다. 비록, 순환유동층(riser)반응기가 전형적인 유동층에 비해 여러 가지 장점 -높은 기-고의 접촉효율, 높은 기체와 고체의 처리량, 기상과 고상의 낮은 축방향 분산, 높은 turndown ratio, 점결성 입자의 처리-을 가지고 있으나, 불균일한 기-고의 흐름에 의한 고체의 역혼합(back-mixing)으로, 기체와 고체의 반경방향의 분리를 일으켜 두상간의 접촉을 감소시켜 생성물의 균일성과 선택도를 감소시킨다. 이러한 riser 반응기의 단점을 보완하기 위해 최근에는 기-고의 하향흐름을 갖는 downer(downflow) 반응기에 대한 관심이 증가하고 있다. (중략)

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.790-797
• /
• 2011

Hydrodynamic similarity was analyzed by employing scaling factor in three phase fluidized beds. The scaling factor was defined based on the holdups of gas, liquid and solid particles and effectivity volumetric flux of fluids between the two kinds of fluidized beds with different column diameter. The column diameter of one was 0.102 m and that of the other was 0.152 m. Filtered compressed air, tap water and glass bead of which density was 2,500 kg/$m^3$ were used as gas, liquid and solid phases, respectively. The individual phase holdups in three phase fluidized beds were determined by means of static pressure drop method. Effects of gas and liquid velocities and particle size on the scaling factors based on the holdups of each phase and effective volumetric flux of fluids were examined. The deviation of gas holdup between the two kinds of three phase fluidized beds decreased with increasing gas or liquid velocity but increased with increasing fluidized particle size. The deviation of liquid holdup between the two fluidized beds decreased with increasing gas or liquid velocity or size of fluidized solid particles. The deviation of solid holdup between the two fluidized beds increased with increasing gas velocity or particle size, however, decreased with increasing liquid velocity. The deviation of effective volumetric flux of fluids between the two fluidized beds decreased with increasing gas velocity or particle size, but increased with increasing liquid velocity. The scaling factor, which was defined in this study, could be effectively used to analyze the hydrodynamic similarity in three phase fluidized processes.

• Korean Chemical Engineering Research
• /
• v.43 no.2
• /
• pp.286-293
• /
• 2005

An interpretation on the solid circulation characteristics in a fluidized-bed process has been carried out as a first step to simulate the dry entrained-bed absorption and bubbling-bed regeneration system for $CO_2$ removal from flue gas. A particle population balance has been developed to determine the solid flow rates and particle size distributions in the process. Effects of principal process parameters have been discussed in a laboratory scale process (absorption column: 25 mm i.d., 6 m in height; regeneration column: 0.1 m i.d., 1.2 m in height). The particle size distributions in absorption and regeneration columns were nearly the same. As gas velocity or static bed height in the absorption column increased, soild circulation rate and feed rate of fresh sorbent increased, however, mean particle diameter decreased in the absorption column. As cut diameter of the cyclone of the absorption column increased, solid circulation rate decreased, whereas feed rate of fresh sorbent and mean particle diameter in the absorption column increased. As attrition coefficient of sorbent particle increased, solid circulation rate and feed rate of fresh sorbent increased but mean particle diameter in the absorption column decreased.

• Korean Chemical Engineering Research
• /
• v.50 no.3
• /
• pp.522-526
• /
• 2012

New experimental method to measure solid descending velocity in a vertical downcomer was presented and effects of downcomer diameter and particle properties on descending velocities for Geldart group A, B, and D particle have been measured and investigated. The effect of initial solid inventory on solid descending velocity was negligible. However, solid flow rate, solid circulation rate and solid descending velocity increased as the downcomer diameter increased. Moreover, solid descending velocity increased linearly as the downcomer diameter increased and showed distinguishable trend for Geldart group D particle from Geldart group A and B particles. Empirical correlations of solid descending velocity for Geldart group D and Geldart group A and B particles have been derived based on the measured values. The correlations could predict well the solid descending velocities.

• Journal of Korea Water Resources Association
• /
• v.30 no.6
• /
• pp.661-669
• /
• 1997

This paper presents a theoretical analysis for a velocity profile of fluid-granule mixed flow and a sheet erosion of an embankment having noncohesive materials due to overflow. The velocity profile were obtained using the stress-strain relationships based on a grain-inertia regime and an erosion depth was obtained using dynamic Coulomb criterion. Experiments were performed to compare with theoretical values and fairly good agreements were found. Theoretical results on velocity profiles, which can be applied to any type of velocity profiles in a fluid-granule mixed flow, showed a considerable improvement for the existing theories on a debris flow. for a design purpose, formulas and figure diagrams for obtaining a velocity profile, an erosion depth, an overflow depth and a granular discharge were proposed for given values of a flood discharge, particle properties and embankment scale.

• Analytical Science and Technology
• /
• v.7 no.4
• /
• pp.483-492
• /
• 1994

Direct solid analysis of various kinds of metal samples has been conducted by glow discharge. In this laboratory, the gas-jet assisted glow discharge(GJGD) device has been developed and characterized. The effect of changes in applied current, cell pressure and flow rate on atomic emission signals obtained from a jet-assisted cathodic sputtering was investigate. The emission intensities of Cu, Zn, and Ar were measured. They were increased with the current. But the intensities were decreased by increasing the flow rate of argon due to the diffusion and transportation of particles into plasma. By increasing the pressure of the cell, the intensities were greatly decreased because of enhancement of redeposition onto the surface of the sample.

• Analytical Science and Technology
• /
• v.15 no.2
• /
• pp.108-114
• /
• 2002

The new system using a glow discharge atomic emission spectrometer for the direct analysis of solid samples has been developed and characterized. The system was consisted of new glow discharge cell improved previous gas-jet boosted nozzle and radio-frequency power supply. In the case of previous type glow discharge chamber, it had been fitted trace analysis of low alloy steel with low discharge power, because it was to decrease redeposition and increase sample weight loss. But it had a problem that plasma becomes unstale due to increased sample weight loss and redeposition resulting from the high discharge power. Because of being problem of previous glow discharge, it is impossible to analyze using high power. The modified gas-jet boosted glow discharge to solve this problem would improve to be less sample loss rate of modified nozzle than sample loss rate of previous nozzle on the equal discharge condition, and improve to increase stability of plasma. The effect of discharge parameters such as discharge pressure, gas flow rate and power on the sample loss rate, emission intensity has been studied to find optimum discharge conditions. The calibration curves of Fe were obtained with 3 low-alloy samples.