• The Journal of the Acoustical Society of Korea
• /
• v.40 no.4
• /
• pp.391-399
• /
• 2021

The conformal array sensor has different sub-array depending on different beam steering directions. According to the method to effective the sensor, the performance of the conformal array sensor can be different, where the sub-array selects an effective sensor. Also, due to the figure of the conformal array sensor, the figure of the sub-array can be different each other, which results in different performance on directivity index, beam width and etc. In this paper, two methods to select sub-array which is the criteria for each sensors position vector and directive vector were proposed. For two sub-array selection methods, the performance of the directivity index, horizontal and vertical beam width were compared with the average and variance. In addition, this comparison was conducted when the number of sensors was fixed. When the number of sensors was not fixed, the directional vector method mainly results in high performance, but the performance of vertical beam width was lower or equal. When the number of sensors was fixed, the performance of two methods is similar, but the performance of variance was deteriorated.

• Journal of the Korean Geotechnical Society
• /
• v.38 no.9
• /
• pp.53-67
• /
• 2022

Micropiles are cast-in-place-type piles with small diameters. They are widely used for the foundation reinforcement of existing buildings and structures because this technique is easy to construct and economic. A base expansion structure is developed following the mechanism of radial expansion at the pile tip under compression. Numerical analysis, durability tests, and centrifuge tests have been conducted using the base expansion structure. In this study, three-dimensional numerical modeling was performed to describe the behavioral mechanism of the base expansion structure using steel bar penetration under compressive loading, and numerical analyses using centrifuge test conditions were performed for the comparative studies. Additionally, the base structure was modified based on the results of lab-scale analyses, and the bearing capacities of micropiles were compared using field-scale numerical analyses under various ground conditions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.4
• /
• pp.417-424
• /
• 2011

A fuel assembly consists of five major components, i.e., a top end piece (TEP), a bottom end piece (BEP), spacer grids (SGs), guide tubes (GTs) and an instrumentation tube (IT); in addition, it also includes fuel rods (FRs). The TEP/BEP should satisfy stress intensity limits according to the conditions A and B of ASME, Section III, Division 1-Subsection NB. In a dual-cooled fuel assembly, the array and position of fuel rods are different from those in a conventional PWR fuel assembly; these changes are necessary for achieving power uprating. The flow plates of the TEP and BEP have to be modified accordingly. The pattern and shape of the flow holes were newly designed. To verify the strength compatibility, the Tresca stress limit according to the ASME code was investigated in the case of an axial load of 22.241 kN. In this paper, the stress linearization procedure for strength evaluation of a newly designed TEP is presented.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.1
• /
• pp.44-50
• /
• 2017

Vehicle Holding Device(VHD) has a role that holding the launch vehicle on its launch pad until the engine therust reaches a steady condition. The analytical study of shape parameters and dynamic characteristics of hydraulic cylinders is carried out. The contraction of cylinder is considered as the major factor of releasing mechanism. Through the analysis, the decreasing of cylinder slit size and increasing initial charging pressure increase the contraction force. Through the transient analysis, cylinder load, displacement and inner pressure distribution are confirmed. The cylinder contraction force is converged to the cylinder external force when the cylinder starts to move. Also, the pressure distribution in the hydraulic cylinder is constant.

• Korean Journal of Optics and Photonics
• /
• v.10 no.5
• /
• pp.373-378
• /
• 1999

White light scanning interferometry is increasingly used for precision profile metrology of engineering surfaces, but its current application is primarily limited to opaque surfaces with relatively simple optical reflection behaviors. In this paper, a new attempt is made to extend the interferometric method to the thickness profile measurement of transparent thin film layers. An extensive frequency domain analysis of multiple reflection is performed to allow both the top and bottom interfaces of a thin film layer to be measured independently at the same time using nonlinear least squares technique. This rigorous approach provides not only point-by-point thickness probing but also complete volumetric film profiles digitized in three dimensions.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1997.10a
• /
• pp.129-134
• /
• 1997

현재 외부 가압 공기베어링이 사용되어지는 분야는 PCB 기판, 엔진의 연료분사노즐 등의 고속가공용 스핀들, 전자 기기, 광학 기기 등에 사용되는 초정밀 부품가공용 스핀들, 정밀 측정 기기, 의료 기기, 저온 팽창기등 상대운동을 하는 많은 분야에서 이용되고 있으며, 이들 분야의 고속화 및 고정밀화 추세에 따라 고속에서의 안정성과 높은 운전정밀도가 보장된 외부 가압 공기 베어링이 요구되고 있다. 정밀 스핀들 시스템에 공기베어링이 사용되는 이유는 윤활제인 공기의 압축성에 기인된 평균화효과로 인하여 어느 정도 형상오차가 존재하더라도 축의 회전 시 떨림 진폭이 흡수되어 높은 운전정밀도를 유지하며 운전이 가능하기 때문이다. 그러나, 공기의 압축성에 의한 평균화효과로 어느 정도의 떨림 진폭은 흡수되나 형상오차에 의한 떨림 진폭은 작은 크기라도 여전히 남아있게 된다. 따라서, 초정밀 가공 기기나 정밀 측정 기기 등 높은 운전정밀도가 요구되는 곳에 공기베어링이 사용될 경우에 있어서 형상오차는 운전정밀도에 영향을 미치는 중요한 인자가 된다. 본 연구에서는 각각 두 개의 오비 가압 공기 저널 및 스러스트 베어링으로 구성된 스핀들 시스템에 대한 축과 베어링의 직각도 오차가 운전정밀도에 미치는 영향에 대해 해석하고 결과를 고찰하여 스핀들 시스템에 있어서 형상 공차에 대한 기초 설계자료를 제시하고자 한다.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.659-664
• /
• 2000

In this paper, We have discussed on the modeling of machined outer geometry which was established for the case of round shape machining, also the effects of externally machined profile are analyzed and its modeling realiability was verified by the experiments of roundness testing, especially in lathe operation. In this study, we established harmonic geometric model with the parameter harmonic function. In general, we can calculate the theoretical roundness profile with arbitrary multilobe parameter. But in real experiments, only 2-5 lobe profile was frequently measured. the most frequently ones are 3 and 5 lobe profile in experiments. With this results, we can predict that these results may be applies to round shape machining such as turning, drilling, boring, ball screw and cylindrical grinding operation in bearing and shaft making operation with the same method. In this study, simulation and experimental work were performed to show the profile behaviors. we can apply these new modeling method in real process for the prediction of part profile behaviors machined such as in round shape machining operation.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.7 no.3
• /
• pp.233-240
• /
• 1995

A large part of shoaling of navigation channel surrounded by fine sand is caused by suspended sediment in non-equilibrium state. We develop a numerical model for predicting shoaling of navigation channel where concentration of suspended sediment in such state is accurately simulated. In this study, effects of channel geometry on the shoaling of the channel are investigated numerically. A composite slope of navigation channel is also proposed to reduce non-equilibrium property of suspended sediment. It is found that the composite slope can effectively reduce non-equilibrium property of suspended sediment and the amount of sediment deposited in the main channel.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.137-137
• /
• 2019

돌출줄눈은 산지하천의 만곡부의 빠른 유속을 감소시키기 위하여 활용된다. 본 연구에서는 친환경 디자인의 나무줄기 돌출줄눈(Tree Trunk Rip, TTR)과 사다리꼴 돌출줄눈(Trapezoid Rip, TR)의 흐름저항을 비교 분석하기 위하여 개수로 수리실험을 수행하였다. 실험은 길이 9m, 폭이 0.6m이며 경사가 0.0035로 고정된 개수로의 한쪽 측벽에 돌출줄눈을 설치하여 진행하였다. 사다리 꼴 돌출줄눈의 형상은 밑변 각이 $63^{\circ}$이며 무차원 설치간격 ${\lambda}_{nv}$가 6, 9, 12인 경우이다. 나무줄기 돌출줄눈의 기본 형상은 사다리꼴이고 표면은 나무껍질 무늬이며 ${\lambda}_{nv}$가 약 10이다. 나무줄기 돌출줄눈의 간격은 사다리꼴 돌출줄눈의 최적 설치 간격 9~12배 범위에 해당되고 평균 마찰계수는 사다리꼴 돌출줄눈의 9~12배의 평균 마찰계수 범위에 포함되었다. 사다리꼴 돌출줄눈의 ${\lambda}_{nv}$가 9, 12일 때의 전체 저항에 대한 형상저항의 비는 평균 $69.4{\pm}5.8%$였으며 나무줄기 돌출줄눈은 $70.2{\pm}2.1%$로 사다리꼴 돌출줄눈과 유사하다. 산지하천 흐름저항을 위한 돌출줄눈 설치에 있어 친환경적 디자인을 고려한 나무줄기가 사다리꼴 돌출줄눈보다 활용도가 클 것으로 기대된다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.57-60
• /
• 2011

The spray characteristics according to the recess length of the GCSC injector and the change of momentum flux ratio(MFR) of the gas and the liquid have been examined through high pressure cold flow test using a high pressure chamber. The liquid in this experiment was water, and the gas was nitrogen. The spray images were taken by a back-lit strobe imaging technique. Results showed that the spray was a wide hollow cone at the lower MFR(liquid velocity was fixed) and the spray became a narrow solid cone as the MFR was increased. And the injector with short recess length produced a narrow solid cone at the higher MFR.