• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.1
• /
• pp.9-14
• /
• 2009

A numerical investigation was performed based on the Reynolds-Averaged Navier-Stokes(RANS) equations for the two-dimensional unsteady flow around a vertical axis turbine(VAT) with three or four blades. VAT is one of the promising devices for tidal current energy conversion. The geometry of the turbine blade was $NACA65_3$-018 airfoil, for which CFD analysis using Fluent was carried out at several angles of attack and the results were compared with the corresponding experimental data for validation and calibration. Then CFD simulations were carried out for the whole vertical axis turbine with a two-dimensional setup. The CFD simulation demonstrated the usefulness of the method to study the typical unsteady flows around VATs and the results showed that the optimum turbine efficiency could be achieved for carefully selected combinations of the number of blade and Tip-Speed Ratio(TSR).

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.16 no.2
• /
• pp.61-70
• /
• 2013

Hydrodynamic aspects on three-dimensional effects were investigated in this study for simple and convenient conversion of tidal stream energy using a Vertical-Axis Turbine (VAT). Numerical approach was made to reveal the differences of flow physics between 2-D estimation and rigorous 3-D simulation. It was shown that the 3-D effects were dominant mainly due to the variation of tip vortices around the tip region of rotor blade, causing the loss of lift for steadily translating hydrofoil and the reduction of torque for rotating turbine blade. The 3-D effect was found to be rather prominent for the typical VATs considered in this paper. Simple and yet efficient 2-D approach with the correction of its three-dimensionality was also proposed for practical design and analysis of VAT.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.10
• /
• pp.2072-2078
• /
• 2011

In photovoltaic(PV) system, for obtaining maximum efficiency of solar power systems, the solar tracking system must be controlled to match position of the sun. In this paper, we design the solar tracking system to track movement of the sun using CdS sensor modules and to determine direction of the sun under shadow of directions. In addition, for an intelligent computation in tracking of the sun, a fuzzy controller is allocated to space avaliable for splitting area of fuzzy part for the fuzzy input space(grid-type fuzzy partition) in which a fuzzy grid partition divides fuzzy rules bases. As well, a simple model of solar tracking system is designed by two-axis motor control systems and the 8-direction sensor module that can measure shadow from CdS sensor modules by matching of axis of CdS modules and PV panels. We demonstrate this systems is effective for fixed location and moving vessels and our fuzzy controller can track the satisfactorily.

• Journal of the wind engineering institute of Korea
• /
• v.22 no.4
• /
• pp.163-169
• /
• 2018

In this study, wind loads exerted on the offshore wind turbine rotor in parked condition were predicted with variations of wind speeds, yaw angles, azimuth angle, pitch angles, and power of the atmospheric boundary layer profile. The calculated wind loads using blade element theorem were compared with those of estimated aerodynamic loads for the simplified blade shape. Wind loads for an NREL's 5 MW scaled offshore wind turbine rotor were also compared with those of NREL's FAST results for more verification. All of the 6-component wind loads including forces and moments along the three axis were represented on a non-rotating coordinate system fixed at the apex of rotor hub. The calculated wind loads are applicable for the dynamic analysis of the wind turbine system, or obtaining the over-turning moment at the foundation of support structure for wind turbine system.

• The KIPS Transactions:PartB
• /
• v.10B no.2
• /
• pp.151-156
• /
• 2003

The vergence control method is presented for a parallel-axls stereo camera (PASC) using a signal processing technique such as shift, (rotation), and scaling. The PASC is considered as the simplest one of binocular stereo cameras. However, its major limitation lies in the controllability of vergence since its left and right imaging sensors of CCDs are fixed. On the other hand, a horizontal-moving-axis stereo camera (HMASC) with movable imaging sensors is able to control the vergence by moving its CCDs horizontally. In spite of its vergence controllability, there is a major drawback in the implementation because of complicated mechanical structure and the additional cost. To overcome the vergence control problem of the PASC, an operational principle of the HMASC is applied to the PASC. To be specific, without any additional hardware the vergence control problem of the PASC is solved with the signal processing technique. Assuming the virtual displacement between CCD's, a disappearing part of acquired images is removed and the original image site is recovered via interpolation. Experimental results show that the vergence control between stereo images captured by the PASC it possible with an acceptable degradation of the image quality defending on the virtual displacement of CCDs.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.5
• /
• pp.913-920
• /
• 2017

In this development, By using the phase array antenna, the beam around was electronically revolved and the marine fixed type radar of which the detection is possible was made and the check around was tested. There are the risk of the corrosion because of the abrasion of the axis of rotation and salinity with the way that the existing marine pulse radar detects the check by using the mechanical rotation. Besides, the maintenance cost of the magnetron gets to happen by using the detection signal. In this development, The fixed type radar of the low output which revolves electronically around the beam by using the radar signal processing method of the phase array antenna using the phase shifter and FMCW(Frequency Modulation Continuous Wave) method was made. And by using the fixed type radar, the check detection test was conducted.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.9 no.3
• /
• pp.45-54
• /
• 2009

This study was developed the metallic plate for bone fixation in the neurosurgery and general surgery and plates has a finn place in bone operating and treatment. The plates can be realized to bending strength and stiffness for strength estimation. Maximum point of bending curves has a bending point(P) with maximum load which to applied nearly 0.2% offset displacement. The device's sizing has a ${\Phi}13$ and ${\Phi}18$, and algorithm of strength estimation compared a plate(${\Phi}13$, ${\Phi}18$, ${\Phi}13-{\Phi}18$). The bending strength of the curved metallic plate has to evaluate maximum of a 311N, 387N, 410N, 474N. When a displacement preserve with a load, tensile stress through to press a plate is 274N, 324N, 382N, 394N. The algorithm of strength estimation can be used to support estimation of bending strength and stiffness. Their tool bring to settlement in the new basic algorithm for evidence with varied adjustment.

• Journal of Broadcast Engineering
• /
• v.15 no.4
• /
• pp.474-486
• /
• 2010

In this paper, we propose a new method for detection moving object contour using spatial and temporal edge. In general, contour pixels of the moving object are likely present around pixels with high gradient value along the time axis and the spatial axis. Therefore, we can detect the contour of the moving objects by finding pixels which have high gradient value in the time axis and spatial axis. In this paper, we introduce a new computation method, termed as temporal edge, to compute an gradient value along the time axis for any pixel on an image. The temporal edge can be computed using two input gray images at time t and t-2 using the Sobel operator. Temporal edge is utilized to detect a candidate region of the moving object contour and then the detected candidate region is used to extract spatial edge information. The final contour of the moving object is detected using the combination of these two edge information, which are temporal edge and spatial edge, and then the post processing such as a morphological operation and a background edge removing procedure are applied to remove noise regions. The complexity of the proposed method is very low because it dose not use any background scene and high complex operation, therefore it can be applied to real-time applications. Experimental results show that the proposed method outperforms the conventional contour extraction methods in term of processing effort and a ghost effect which is occurred in the case of entropy method.

• Journal of the Korean Magnetics Society
• /
• v.20 no.2
• /
• pp.35-40
• /
• 2010

The GMR-SV (giant magnetoresistance-spin valve) device depending on the micro patterned features according to two easy directions of longitudinal and transversal axes has been studied. The GMR-SV multilayer structure was Ta(5 nm)/NiFe(8 nm)/Cu(2.3 nm)/NiFe(4 nm)/IrMn(8 nm)/Ta(2.5 nm). The applied anisotropy direction of the GMR-SV thin film was performed under the magnitude of 300 Oe using by permanent magnet during the deposition. The size of micro patterned device was a $1\;{\times}\;18\;{\mu}m^2$ after the photo lithography process. In the aspects of the shape magnetic anisotropy effect, there are two conditions of fabrication for GMR-SV device. Firstly, the direction of sensing current was perpendicular to the magnetic easy axis of the pinned NiFe/IrMn bilayer with the transversal direction of device. Secondly, the direction of shape magnetic anisotropy was same to the magnetic easy axis of the free NiFe layer with the longitudinal direction of device.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.796_797
• /
• 2009

1kW급 저소음 수직형 풍력발전기용 동기발전기 설계에 대해 설명한다. 낮은 풍량에 유리한 수직형 블레이드 특성에 맞춰 발전기는 코깅 토크가 낮아야 하며, 고효율화를 위해 다극형 설계가 유리하다. 현제 국내 수직형 풍력에 적합한 발전기가 대부분이며 수직형 풍력발전기에 적합한 낮은 코깅 토크의 발전기는 일반화 되어있지 않다. 본 논문에서는 동기발전기 최적 설계를 통해 코깅토크를 최소화 시켰고, 다극형 형태를 통해 낮은 풍량에서 고효율 출력을 만들어낼 수 있도록 200rpm에서 역기전력 96V, 1kw의 정격출력을 가지도록 설계 하였다. 수직축형태의 블레이드에 구조에 맞춰 축계통형 발전기 구조를 가지고 있고, 유한요소해석법을 이용 회전자, 고정자, 권선법, 영구자석 등의 구조를 최적화 시켰다.