• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2007.12a
• /
• pp.34-36
• /
• 2007

현재 모형선을 이용한 선형성능 검증방법에는 크게 2가지 방법이 있다. 첫째는 예인수조에서 예인전차를 이용하여 정수중에 배를 예인시켜 그에 따른 저항을 시험하는 방법이 있고, 둘째는 회류수조에서 배를 고정하여 물을 회전시켜 모형선의 저항을 측정하는 방법이 있다. 이와 같은 방법은 저속 및 대형선박을 검증하기 위해 계발된 방법들로 소형 고속어선 및 고속레저선박의 저항성능 평가를 수행하기 어려운 것이 현실이다. 예인전차의 예인속도와 회류수조 물의 유속이 소형 고속어선 및 고속레저선박의 속력에 미치지 못하기 때문이다. 따라서 고속을 요하는 선박의 저항성능 평가를 위해 새로운 방법 연구가 필요하다. 이에 고속선의 저항성능 시험을 위해 실 해상에서 일반 선박을 이용하여 예인하는 방법을 적용하여 저항시험을 수행하였으며 그에 맞는 시스템을 설계하였다.

• Journal of Navigation and Port Research
• /
• v.31 no.10
• /
• pp.813-818
• /
• 2007

There are the C.W.C and Towing Tank to the model-test equipments of the boat. A model testing of the high speed boat have a difficult in the performance verification because of very a small the scale-ratio of the ship-model and restricted by flow-velocity of the C.W.C and X-carriage velocity of the T.T. In general, the stepped hull boat is a high of fuel-efficiency because of the resistance reduction by a small wetted surface-area in correspond without stepped-hull boat. But It have a tendency to be bad the rolling performance by reduced stern wetted-area In this paper, the high speed stepped planning-boats with & without attached a stern body were performed to compare the effect of resistance and rolling performance by using sea model-test method.

• Journal of Navigation and Port Research
• /
• v.34 no.8
• /
• pp.623-628
• /
• 2010

High speed marine vehicle, such as semi-planing, planing craft have been developed recently. These ships paid attention to the resistance characteristics, especially in high speed region. Model test method is divided to two equipment greatly, first 'Towing tank', second 'C.W.C.'. It is difficult to estimate a resistance characteristics for high speed boat. because these are made for low speed ship. This paper suggests a new model test method and system. This is real sea model test and it's comprised of eight part. Firstly, This method is tested at C.W.C that is possible to using in real sea model tes using low speed boat modelt. And then, Real sea model test and CFD calculation are performed and compared with tow way used high speed boat model. It can be a good way to estimate a performance for high speed boat.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.2
• /
• pp.1-5
• /
• 2001

A study on the new active type oil-water separation system including the oil-water separation system of magnetic film was carried out. Separation system is composed of several active types of circulating oil separation steps and one magnetic film separation step at final stage. At the magnetic separation step, ferrofluid easily forms a weak magnetic mixture with oil, which is from the water by magnetic field gradient. The vessel has been designed to run at the maximum speed of 25 knots. And two typical forms of SWATH and Catamaran have been studied as a new type of oil recovery vessel.

• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.3
• /
• pp.100-111
• /
• 1994

This study was carried out for understanding the characteristics of the spray around high speed vessels. Prismatic planing hull made of an acrylate board was used to the tests. The distribution of local spray velocity were estimated from the analysis of the spray visualization. A new test system for measuring the spray thickness is proposed, and was used to estimate the local spray thickness in the model. The pressure distributions on the bottom of the hull are measured and integrated to estimate the pressure drag of the model in the towing tests. Finally. the spray drag/lift component is separated from the total drag/lift on the prismatic hull. These test results show that the spray drag component on high speed vessels is relatively large and important in total drag.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.19 no.4
• /
• pp.397-402
• /
• 2013

In this study, numerical hull form development of a platform supply vessel, a full scale with the overall length of 26.75m, was performed to predict a bare-hull resistance and a large scale of model tests with a 1/10 scaled model were conducted to verify the success of numerical results. Numerical analysis on heave and pitch motion as a function of encounter frequency and ship's speed for the prediction of seakeeping characteristics are also presented. The experiment results of resistance agreed well with numerical analysis. As a result in the motion response characteristics, the heave RAO indicates high values with the range of encounter frequency 1.8~2.0. The Pitch RAO indicates high motion response characteristics at Beaufort scale No. 3 and 4 in rough seas.

• Journal of the Society of Naval Architects of Korea
• /
• v.55 no.5
• /
• pp.401-414
• /
• 2018

Planing hull type ships are often equipped with interceptor or trim tab to improve the excessive trim angle which leads to poor resistance and sea keeping performances. The purpose of this study is to design a controller to control the attitude of the ship by controllable stern interceptor and validate the effectiveness of the attitude control by the towing tank test. Embedded controller, servo motor and controllable stern interceptor system were equipped with planing hull type model ship. Prior to designing the control algorithm, a model test was performed to identify the system dynamic model of the planing hull type ship including the stern interceptor. The matrix components of model were optimized by Genetic Algorithm. Using the identified model, PID controller which is a classical controller and sliding mode controller which is a nonlinear robust controller were designed. Gain tuning of the controllers and running simulation was conducted before the towing tank test. Inserting the designed control algorithm into the embedded controller of the model ship, the effectiveness of the active control of the stern interceptor was validated by towing tank test. In still water test with small disturbance, the sliding mode controller showed better performance of canceling the disturbance and the steady-state control performance than the PID controller.