• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.11 s.353
• /
• pp.37-47
• /
• 2006

This work proposes a 10b 25MS/s $0.8mm^2$ 4.8mW 0.13um CMOS A/D Converter (ADC) for high-performance wireless communication systems such as DVB, DAB and DMB simultaneously requiring low voltage, low power, and small area. A two-stage pipeline architecture minimizes the overall chip area and power dissipation of the proposed ADC at the target resolution and sampling rate while switched-bias power reduction techniques reduce the power consumption of analog amplifiers. A low-power sample-and-hold amplifier maintains 10b resolution for input frequencies up to 60MHz based on a single-stage amplifier and nominal CMOS sampling switches using low threshold-voltage transistors. A signal insensitive 3-D fully symmetric layout reduces the capacitor and device mismatch of a multiplying D/A converter while low-noise reference currents and voltages are implemented on chip with optional off-chip voltage references. The employed down-sampling clock signal selects the sampling rate of 25MS/s or 10MS/s with a reduced power depending on applications. The prototype ADC in a 0.13um 1P8M CMOS technology demonstrates the measured DNL and INL within 0.42LSB and 0.91LSB and shows a maximum SNDR and SFDR of 56dB and 65dB at all sampling frequencies up to 2SMS/s, respectively. The ADC with an active die area if $0.8mm^2$ consumes 4.8mW at 25MS/s and 2.4mW at 10MS/s at a 1.2V supply.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.3A
• /
• pp.235-249
• /
• 2011

A new form of I-type PSC bridge girder, which has hole in the web, is proposed in this paper. Three different concepts were combined and implemented in the design. First of all, a girder was precast at a manufacturing plant as divided pieces and assembled at the construction site using post-tensioning method, and the construction period at the site will be reduced dramatically. In this way, the quality of concrete can be assured at the manufacturing factory and concrete curing can be well controlled, and the spliced girder segments can be moved to the construction site without a transportation problem. Secondly, a numerous number of holes was made in the web of the girder. This reduces the self-weight of the girder. But more important thing related to the holes is that about half of the total anchorages can be moved from the girder ends into individual holes. The magnitude of negative moment developed at girder ends will be reduced. Also, since the longitudinal compressive stresses are reduced at ends, thick end diaphragm is not necessary. Thirdly, Prestressing force was introduced into the member through multiple stages. This concept of multi-stage prestressing method overcomes the prestressing force limit restrained by the allowable stresses at each loading stage, and maximizes the magnitude of applicable prestressing force. It makes the girder longer and shallower. Two 50 meter long full scale girders were fabricated and tested. One of them was non-spliced, or monolithic girder, made as one piece from the beginning, and the other one was assembled using post-tensioning method from five pieces of segments. It was found from the result that monolithic and spliced girder show similar load-deflection relationships and crack patterns. Girders satisfied specific girder design specification in flexural strength, deflection, and live load deflection control limit. Both spliced and monolithic holed web post-tensioned girders can be used to achieve span lengths of more than 50m with the girder height of 2 m.

• Journal of the Korean Chemical Society
• /
• v.64 no.2
• /
• pp.67-73
• /
• 2020

The study aimed to investigate in vitro lipid deposition of oleic acid, oleic acid methyl ester and cholesterol on a daily disposable (1-day lenses) and 3-days lenses over 3 days and changes of optical characteristics is also investigated. Artificial tear solutions were prepared to simulate actual tear compositions. Two types of contact lenses (1-day lenses (Senofilcon A) and 3-days lenses (silicone tripolymer)) were soaked in the artificial tear solutions within an incubator at 37 ℃ with 150 rpm for 8, 16, 24 hours. Lipid deposition (oleic acid, oleic acid methyl ester and cholesterol) were measured using high performance liquid chromatography (HPLC) instrument. In addition, measurements of oxygen transmissibility, light transmittance and observation of lens surface were conducted. The amount of lipid deposition on the 1-day lenses were 127.55 ㎍/lens for Day 1, 302.96 ㎍/lens, for Day 2, and 353.30 ㎍/lens for Day 3. The 3-days lenses were 46.22 ㎍/lens for Day 1, 66.07 ㎍/lens for Day 2, and 67.45 ㎍/lens for Day 3. Oxygen transmissibility were 81×10^-9(cm/sec)(ml O₂/ml×mmHg)(Baseline) and 48×10^-9(cm/sec)(ml O₂/ml×mmHg) (Day 3) for the 1-day lenses, it were 13.23×10^-9(cm/sec)(ml O₂/ml×mmHg)(Baseline) and 9.6×10^-9(cm/sec)(ml O₂/ml×mmHg) (Day 3) for the 3-days lenses. Transmittance of each lenses were 97.21% (Baseline) and 94.25% (Day 3) for the 1-day lenses, 97.65% (Baseline) and 95.15% (Day 3) for the 3-days lenses. Observation of surface deposition indicated greatest deposition for the 3-days lenses type on Day 3. Lipid deposition for both lens types increased by day and was greater for the 1-day lenses type. Surface deposition appeared to differ as it was greatest for the 3 days lens type, which may suggest other deposits such as protein may be present.

• The Korean Journal of Air & Space Law and Policy
• /
• v.29 no.2
• /
• pp.135-161
• /
• 2014

An unmanned aerial vehicle (UAV), commonly known as a drone and also referred to as an unpiloted aerial vehicle and a remotely piloted aircraft (RPA) by the International Civil Aviation Organization (ICAO), is an aircraft without a human pilot aboard. ICAO classify unmanned aircraft into two types under Circular 328 AN/190. Unmanned aircraft, which is the core of the development of the aviation industry. However, there are also elements of the legal dispute. Unmanned aircraft are manufactured in small size, it is possible to shoot a record peripheral routes stored in high-performance cameras and sensors without the consent of the citizens, there is a risk of invasion of privacy. In addition, the occurrence of the people of invasion of privacy is expected to use of civilian unmanned aircraft. If the exposure of private life that people did not want for unmanned aircraft has occurred, may occur liability to the operator of unmanned aircraft, this is a factor to be taken into account for the development of unmanned aircraft industry. In the United States, which is currently led by the unmanned aircraft industry, policy related to unmanned aircraft, invasion of privacy is under development, is preparing an efficient measures making. Unmanned aircraft special law has not been enforced. So there is a need for legal measures based on infringement of privacy by the unmanned aircraft. US was presented Privacy Protection Act of unmanned aircraft (draft). However Korea has many laws have been enacted, to enact a new law, but will be able to harm the legal stability, there is a need for the enactment of laws for public safety of life. Although in force Personal Information Protection Law, unmanned aerospace, when the invasion of privacy occurs, it is difficult to apply the Personal Information Protection Law. So, it was presented a privacy protection bill with infringement of privacy of unmanned aircraft in the reference US legislation and the Personal Information Protection Act.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.5
• /
• pp.1323-1329
• /
• 2020

To characterize the molecular structure of PhE-gal synthesized using Escherichia coli 𝛽-gal, NMR (¹H- and ¹³C-) spectroscopy and mass spectrometry of PhE-gal were conducted. ¹H NMR spectrum of PhE-gal showed multiple peaks corresponding to the galactosyl group, which is an evidence of galactosylation on 2-phenylethanol (PhE). Downfield proton peaks at 𝛿_H 7.30~7.21 ppm showed the presence of aromatic protons of PhE as well as benzyl CH₂ protons at 𝛿_H 2.88 ppm. Up field proton peaks at 𝛿_H 4.31 ppm, 4.07 ppm and multiple peaks from 𝛿_H 3.86~3.38 ppm are indicative of galactocylation on PhE. ¹³C NMR spectrum revealed the presence of 12 carbons suggestive of PhE-gal. Among 12 carbon peaks from PhE-gal, the four peaks at 138.7, 129.0, 128.6 and 126.5 were assigned aromatic carbons in the phenyl ring. Three peaks at 129.0, 128.6 and 126.5 showed high intensities, indicating CH aromatic carbons. ¹³C NMR data of PhE-gal showed 6 monosaccharide peaks from galactose and 2 peaks from aliphatic chain of PhE, indicating that PhE-gal was galactosyl PhE. The mass value (sodium adduct ion of PhE-gal, m/z = 307.1181) from mass spectrometry analysis of PhE-gal, and ¹H and ¹³C NMR spectral data were in good agreement with the expecting structure of PhE-gal. We are expecting that through future study it will eventually be able to develop a new additive with low cytotoxicity.

• Journal of the Mineralogical Society of Korea
• /
• v.28 no.3
• /
• pp.245-253
• /
• 2015

The performance of $TiO_2$ photo-catalytic oxidation process is significantly dependent on the amount of hydroxyl radicals produced during the process, and it is an essential prerequisite to quantify its production. However, precise and accurate methods for quantification of hydroxyl radicals have not been developed so far. For this reason, this study was initiated to compare existing methods for analysis of hydroxyl radicals produced by $TiO_2$ photo-catalytic oxidation and to propose a new method to overcome the limitation of established methods. To simulate $TiO_2$ photo-catalytic oxidation process, Degussa P25 which has been widely used as a standard $TiO_2$ photo-catalyst was used with the dose of 0.05 g/L. The light source of process was UVC mercury low-pressure lamp (11 W, $2,975mW/cm^2$). The results indicate that both potassium iodide (KI)/UV-vis spectrometer and terephthalic acid (TPA)/fluorescence spectrometer methods could be applied to qualitatively measure hydroxyl radicals via detection of triiodide ion ($I_3{^-}$) and 2-hydroxyterephthalic acid which are produced by reactions of iodine ion ($I^-$) and TPA with hydroxyl radicals, respectively. However, it was possible to quantitatively measure hydroxyl radicals using TPA method coupled with high-performance liquid chromatograph (HPLC). The analytical results using TPA/HPLC method show that hydroxyl radical of 0.013 M was produced after 8 hours operation of photo-catalytic oxidation under specific experimental conditions of this study. The proposed method is expected to contribute to precise the evaluation of the performance of photo-catalytic oxidation process.

• Journal of the Korean Society of Radiology
• /
• v.6 no.1
• /
• pp.73-77
• /
• 2012

Recently, Interest to the photoconductor, which is used to flat form X-ray detector such as a-Se, $HgI_2$, PbO, CdTe, $PbI_2$ etc. is increasing. In this study, the film layer by using the photoconductive material with particle sedimentation was fabricated and evaluated. The quantization efficiency of the continuous X-ray with the 70 kVp energy bandwidth was analyzed by using the Monte Carlo simulation. With the results, the thickness of film with 64 % quantization efficiency was 180 ${\mu}m$ which is similar to the efficiency of 500 ${\mu}m$ a-Se film. And $HIg_2$ film has the high quantization efficiency of 74 % on 240 ${\mu}m$ thickness. The electrical characteristics of the 239 ${\mu}m$ $Hgl_2$ films produced by particle sedimentation were shown as very low dark current(under 10 $pA/mm^2$), and high sensitivity(19.8 mC/mR-sec) with 1 $V/{\mu}m$ input voltage. The SNR, which is influence to the contrast of X-ray image, was shown highly as 3,125 in low driving voltage on 0.8 $V/{\mu}m$. With the results of this study, the development of the low-cost, high-performance image detector with film could be possible by replacing the film produced by particle sedimentation instead to a-Se detector.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.19 no.1
• /
• pp.76-87
• /
• 2014

Chlorophyll a in seawater which is an indicator of phytoplankton biomass and primary production is determined by High Performance Liquid Chromatography (HPLC), Fluorometry and Spectrophotometry. In this study, various methods for chlorophyll a determination in seawater are compared using in situ seawater samples from Korean seas. Three inter-laboratory comparison campaigns were carried out using chlorophyll a standard samples (R0) and in situ seawater samples, collected from the East China Sea (R1) and the East Sea (R2). 6 laboratories by HPLC methods, 4 laboratories by fluorometry, and 3 laboratories by spectrophotometry participated. Precisions, defined as the coefficient of variation (CV) were within 9% in standard samples, 0.8~20% (average: 6.1%) in R1, 4~21% (average: 13.2%) in R2. Discrepancy in three methods was approximately 20% within the range of the sample homogeneity intended the laboratory precision (R1: 8%, R2: 15%). The discrepancy in laboratories was greater than the discrepancy in methods. The chlorophyll a concentrations can be produced within 20% discrepancy in spite of using different methods. It is recommended to consider this 20% discrepancy when using the chlorophyll a data produced by different laboratories and different methods.

• Korean Journal of Food Science and Technology
• /
• v.12 no.3
• /
• pp.193-199
• /
• 1980

A series of tests were conducted on the reesterification of rice bran oil containing high free fatty acids (acid value=119.7) with theoretical equivalent of glycerol. Test results showed that reaction rate (in terms of decrease in acid value) was increased as the reaction temperature was increased regardless of the presence of the catalyst and reaction time (42.7, 21.5 and 10.0 at $170^{\circ}C,\;210^{\circ}C\;and\;250^{\circ}C$, respectively) and as the reaction time was increased regardless of the temperature and the presence of the catalyst (31.1 vs 18.3 for 3 hrs vs 6 hrs). The presence of the catalyst (0.2% tin chloride) also accelerated the rate regardless of the reaction temperature and time (36.9 vs 12.5). Analysis by column chromatography showed that content of triglyceride in the oil was increased to 72.9% and 61.1% from 10.4% and content of free fatty acids in the oil was decreased to 1.4% and 6.1% from 60.2%, when the degummed oil was esterified at $250^{\circ}C$ for 6 hrs in the presence of and in the absence of the catalyst, respectively. The results estimated from the iodine values indicate that polymer formation was not significant, when the oil was esterified for 6 hrs at temperatures up to $210^{\circ}C$. However, it was somewhat significant for the oil esterified at $250^{\circ}C$ for 6 hrs. The catalyst did not affect the polymer formation. Analysis by high performance liquid chromatography showed that oleic acid (42.5%), linoleic acid (29.0%) and palmitic acid (20.3%) were the major fatty acid components of the rice bran oil.

• Tuberculosis and Respiratory Diseases
• /
• v.50 no.2
• /
• pp.158-170
• /
• 2001

Background : Although an oxidants and antioxidants imbalance has been considered in the pathogenesis of chronic obstructive pulmonary disease (COPD), there is a paucity of reports focussing on the smoking-induced changes of oxidants and antioxidants in COPD. Method : The concentration of antioxidants (ascorbic acid, uric acid, retinol, and $\alpha$- & $\gamma$-tocopherol) was measured in the serum and induced sputum of 30 healthy controls and 34 stable COPD patients using high performance liquid chromatography (HPLC). The inhibition of lipid peroxidation as an index of antioxidant capacity was measured in the serum by a TBA assay. Results : The serum concentration of ascorbic acid, $\alpha$-tocopherol, and retinol were significantly lower in the patients with COPD than in healthy controls ($484.8{\pm}473.3$ vs $1497.8{\pm}819.2\;pmol/L$, $48.38{\pm}17.34$ vs $73.96{\pm}26.29\;pmol/L$, p<0.001, and $9.51{\pm}8.33$ vs $15.01{\pm}5.88\;pmol/L$, p<0.05, respectively, mean$\pm$SD). However, there were little differences in the ascorbic acid and uric acid concentrations in the induced sputum between the COPD patients and the controls. The induced sputum to serum ratio of ascorbic acid was significantly higher in COPD patients compared with healthy control (0.375 vs 0.085, p<0.05). In the normal controls, the serum ascorbic acid concentration was lower in smokers than in nonsmokers ($1073{\pm}536$ vs $1757{\pm}845\;pmol/L$, p<0.05), but the level was still higher than that of the COPD patients (p<0.05). The serum retinol levels were correlated with $FEV_1$ in COPD patients (r=0.58, p<0.05). The products of lipid peroxidation were increased in normal smokers and COPD compared with norma1 nonsmokers ($115.56{\pm}19.93$ vs $120.02{\pm}24.56$ vs $91.87{\pm}20.71\;{\mu}mol/{\mu}mol$ Pi of liposome, p<0.05). Conclusion : Cigarette smoking may induce the dep1etion of serum antioxidants and this depletion of antioxidants is suggested to play a role in the pathogenesis of COPD.