• Polymer(Korea)
• /
• v.37 no.3
• /
• pp.347-355
• /
• 2013

In this study, the porous cellulose hydrogel as a carrier to enhance the skin delivery of quercetin and its glycoside, rutin known as flavonoid antioxidants was prepared and its properties were investigated. The optimum cellulose hydrogel for quercetin and rutin was made by the reaction of 2 wt% cellulose with 12% ECH. In the release test of the hydrogel containing the flavonoids, the release of quercetin was diffusion-controlled at $10{\sim}500{\mu}M$, but rutin was released by the erosion of hydrogel system at $10{\sim}50{\mu}M$. Both the encapsulation efficiency and release amount of rutin in hydrogel were higher than quercetin. However, in skin permeation experiment using Franz diffusion cell, quercetin showed higher skin permeation capacity than rutin. The hydrogel containing flavonoids showed remarkable transdermal permeation than the control group. These results suggest that porous cellulose hydrogel is potential drug delivery system to enhance transdermal permeation of water-insoluble flavonoid antioxidants.

• Clean Technology
• /
• v.11 no.1
• /
• pp.41-50
• /
• 2005

In this study, semibatch emulsion copolymerization of n-BA as adhesive component and MMA as coagulant component were carried out for the stable acrylic polymer latex in aqueous phase for polymer cement using LE-type nonionic surfactant as environmental friendly surfactant. The stable polymer emulsion was obtained with the increases of chain length(n) of this surfactant. The effect on the amount of LE-50 as nonionic surfactant were showed that the concentration of polymer latex were increased by increasing the amount of LE-50, whereas the average particle size were decreased by increasing the amount. The addition of functional monomer in initial reactor charge showed a significant effect on the final polymer concentration and the latex particle size. The single polymerization of each n-BA or MMA showed a very low concentration of polymer latex and very big particle size due to coagulation. In the polymerization composed of mixed monomer with MMA and n-BA, the larger the ratio of MMA to n-BA in the copolymers, the greater the amount of coagulum produced. It was found that a stable copolymers were obtained in the range of 15-35 % of n-BA. Moreover, incorporation of some functional monomers in addition to of main monomers became more stable polymer latex. Through DSC and IR analysis, the final polymer latex was composed by MMA/n-BA/AA/AM with a single Tg depending on the reaction conditions. As a result, the conditions of this acrylic polymerization could also be effectively controlled to get the desired final products.

• Polymer(Korea)
• /
• v.30 no.1
• /
• pp.75-79
• /
• 2006

Silica nanoparticles for polymeric dental restorative composites were prepared by Stober method, and then the effects of surface treatment of silica particles with Lmethacrylofpropyltrimethofsilane $(\gamma-MPS)$ on the dispersity of the silica particles in the organic matrix was investigated. Particles having various average size were prepared by using controlled amounts of tetraethylorthosilicate(TEOS), water, and catalyst and by changing solvent used for reaction. The site of particles prepared by using methanol as solvent was smaller than that prepared by using ethanol as solvent. In addition, the size of particles was increased by decreasing amounts of water and by increasing amounts of TEOS and catalyst. Hydrophobic silica nanoparticles was prepared by reacting hydrophilic nanoparticles with $\gamma-MPS$ to improve interfacial properties with organic matrix. Amounts of $\gamma-MPS$ per unit mass of the particles was increased by decreasing particle size. even though the amount of $\gamma-MPS$ per specific surface area were nearly the same regardless of the particle size. The dispersity of the silica particles in the organic matrix was improved when the surface treated silica particles were used for preparing the polymeric dental restorative composites.

• Polymer(Korea)
• /
• v.26 no.2
• /
• pp.260-269
• /
• 2002

The fire resistance of particulate polypropylene composite systems were investigated by using various reinforced particles such as zeolite, talc, $CaCO_3$ particles. In this study, The effect of particle size on the thermal properties of composite and the effect of reinforced particles on the fire resistance were studied. The inorganic reinforced particles used in this study were recycled zeolite(average particle diameter=85.34 $mu extrm{m}$), $CaCO_3$ (33.93 $mu extrm{m}$), and talc (18.51 $mu extrm{m}$). The fire resistance of composite systems was thoroughly examined by measuring limited oxygen index (LOI, ASTM D2863) and cone calorimetry (ASTM E1354, ISO 5660). Thermal stability of composite systems was thoroughly examined by measuring TGA. The flame retardants (DBDPO) and reinforced particles reduce the maximum heat release rate (M-HRR) in the order of Talc > $CaCO_3$ > recycled Zeolite. Comparing the cone calorimetry experimental results of the particle reinforced polymer composite system exhibited twice higher efficiency than DBDPO in polypropylene systems, and the LOI also showed similar trends to the cone calorimetry experiments. The optical and scanning electron microscopy techniques were used to investigate the composites ash layer and the core fracture surfaces in the burning process. The reinforcing inorganic particles seemed to accumulate at the surface of ash layer, and subsequently intercept the oxygen transport and heat transfer into the core area.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.144-149
• /
• 2014

Large residual stresses are remained in the conventional injection molded products because of the high cavity pressure in packing phase during injection molding process. Conventional injection molding (CIM) invokes distribution of cavity pressure and it has a limitation to obtain product with uniform physical property. Multi-cavity conventional injection molding contains quality deviation among the cavities since flow imbalance occurs during filling phase. Injection compression molding (ICM) is adopted to overcome these limitations of CIM. In this study, molding characteristics of CIM and ICM have been investigated using multi-cavity injection mold. Researches were performed by both experiment and computer simulation through observations of birefringence for transparent resins, polycarbonate and polystyrene in CIM and ICM. As a result, low and uniform birefringence and mold shrinkage were showed in the specimens by ICM that could give a uniform cavity pressure. Deviation of physical property among the specimens in multi-cavity mold shown in CIM was significantly reduced in the specimens by ICM. Through this study it was concluded that the ICM in multi-cavity molding was valid for molding products with uniform property in an individual cavity and also reduced property deviation among the cavities.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.596-605
• /
• 2016

In previous years, practice hand grenades were composed of non-degradable plastics and caused environmental pollution. Therefore, this study applied PLA(Polylactic acid) to practice hand grenades that would biodegradable within a short time. High expectations are being placed on PLA as a substitute for plastics because it can decompose to water and carbon dioxide. The aim of this study was to confirm that the PLA material of a practice hand grenade has biodegradability in a pilot-scale composting unit and estimate the applicability for other items. A composting test was progressed according to ISO 16929(2013). The test process was found to be valid. At the end of the composting test (after 12 weeks), the entire content of the test bin with the test sheet was sieved, sorted and analyzed. A disintegration percentage of 99.2% was obtained after 12 weeks of composting. Therefore, the 90% pass level required by ISO 17088(2013), EN 13432(2000), and ASTM D 6400-12 was easily reached. On the other hand, more research will be needed to determine additional applications of PLA material for consumables.

• Applied Chemistry for Engineering
• /
• v.25 no.4
• /
• pp.418-424
• /
• 2014

The improved thermal stability and anti-oxidation properties of Lyocell fiber were studied based on flame retardant treatment by using NaCl/$H_3PO_4$ solution. The optimized conditions of flame retardant treatment were studied on various maxing ratio of NaCl and $H_3PO_4$ and the mechanism was proposed through experimental results of thermal stability anti-oxidation. The IPDT (integral procedural decomposition temperature), LOI (limited oxygen index) and $E_a$ (activation energy) increased 23, 30 and 24% respectively via flame retardant treatment. It is noted that thermal stability and anti-oxidation improved based on char and carbon layer formation by dehydrogenation and dissociation of C-C bond resulting the hindrance of oxygen and heat energy into polymer resin. The optimized conditions for efficient flame retardant property of Lyocell fiber were provided using NaCl/$H_3PO_4$ solution and the mechanism was also studied based on experimental results such as IDT (initial decomposition temperature), IPDT, LOI and $E_a$.

• Polymer(Korea)
• /
• v.36 no.5
• /
• pp.612-616
• /
• 2012

In this work, the effect of chemical treatments of multi-walled carbon nanotubes (MWNTs) on the mechanical interfacial properties of carbon fiber fabric-reinforced composites was investigated. The surface properties of the MWNTs were determined by acid and base values, Fourier transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS) analyses. The mechanical interfacial properties of the composites were assessed by interlaminar shear stress (ILSS) and critical stress intensity factor ($K_{IC}$). The chemical treatments based on acid and base reactions led to a significant change of surface characteristics of the MWNTs, especially A-MWNTs/carbon fibers/epoxy composites had higher mechanical properties than those of B-MWNTs and non-treated MWNTs/carbon fibers/epoxy composites. These results were probably due to the improvement of interfacial bonding strength, resulting from the acid-base interaction and hydrogen bonding between the epoxy resins and the MWNT fillers.

• Polymer(Korea)
• /
• v.38 no.5
• /
• pp.676-681
• /
• 2014

Licorice, widely used as a herbal medicine, has flavonoids such as liquiritin and its aglycone, liquiritigenin that show anti-oxidant and anti-inflammatory properties. Licorice flavonoid-loaded cellulose hydrogels were prepared as carriers for skin drug delivery, and their properties were investigated. The porous cellulose hydrogel was made by reacting cellulose with epichlorohydrin as a cross-linking agent in NaOH/urea(1~10%) solutions. Through studies on the rheological properties and water uptake of the hydrogel, a NaOH/urea(6%) solution was established as being optimum for the synthesis of the cellulose hydrogel containing liquiritin and liquiritigenin. Scanning electron microscopy (SEM) observations of a cross-section of the prepared hydrogel indicated its porosity. In particular, in skin permeation experiments using a Franz diffusion cell, hydrogel containing the licorice flavonoids showed remarkable transdermal permeation compared to the control group. These results indicate that porous cellulose hydrogel is a potential drug delivery system to enhance the skin permeation of licorice flavonoids.

• Fire Science and Engineering
• /
• v.29 no.2
• /
• pp.25-32
• /
• 2015

The improved thermal stability and anti-oxidation properties of lyocell fiber were studied based on flame retardant treatment by using $Na_3PO_4$ solution. The optimized conditions of flame retardant treatment were studied on various concentrations of $Na_3PO_4$ and the mechanism was proposed through experimental results of thermal stability and anti-oxidation. The integral procedural decomposition temperature (IPDT), limiting oxygen index (LOI) and activation energy ($E_a$) increased 30, 160% respectively via flame retardant treatment. It is noted that thermal stability and anti-oxidation improved based on char and carbon layer formation by dehydrogenation and dissociation of C-C bond resulting the hindrance of oxygen and heat energy into polymer resin. The optimized conditions for efficient flame retardant property of lyocell fiber were provided using $Na_3PO_4$ solution and the mechanism was also studied based on experimental results such as initial decomposition temperature (IDT), IPDT, LOI and $E_a$.