• Journal of Sensor Science and Technology
• /
• v.4 no.3
• /
• pp.71-79
• /
• 1995

For the fabrication of high sensitive intrinsic fiber optic Fabry-Perot interferometeric sensor, the deposition conditions of $TiO_{2}$ thin film used to the internal mirrors of the sensor were investigated. The $TiO_{2}$ film deposited by RF magnetron sputter had higher refractive index ($2.36{\sim}2.48$) and better stoiciometry (O/Ti = 2) than that deposited bye-beam evaporator. In the case of forming $TiO_{2}$ internal mirror by using fusion splicing technique, the $TiO_{2}$ reflection mirror deposited by RF magnetron sputter in the condition of 120W RF power showed high. reflectance and excellent controllability of reflection power. The fabricated intrinsic fiber optic Fabry-Perot interferometer with two $TiO_{2}$ internal mirrors deposited under the condition showed very stable fringe patterns. It is, therefore, expected that the interferometer will be applicable to various high precision sensors.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.12
• /
• pp.1367-1374
• /
• 2008

A new high-gain Fabry-$P{\acute{e}}rot$ cavity antenna for wireless broadband internet(Wibro) base station antennas, which is covered with metamaterial superstrate presenting simultaneous negative values of permittivity and permeability, is proposed. To facilitate the fabrication process using the printed circuit board(PCB) technology of today, a new planar-type metamaterial superstrate is designed, which shows negative and low positive values of a refractive index near the Wibro service frequency band. And the principle of antenna gain enhancement is analyzed from the two different view points of effectively low refractive index and of the Fabry-$P{\acute{e}}rot$ resonance condition. Single square patch antenna is used as a feeder. The separation distance is determined by considering the reflection phases of the metamaterial superstrate and the substrate satisfying Fabry-$P{\acute{e}}rot$ resonance condition, respectively. Comparison between the prediction and the measurement shows good agreement, which verifies the validity of our design approach.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.320-320
• /
• 2012

III-V 화합물 태양전지는 실리콘, CdTe, CIGS, 염료, 및 유기 등 다른 태양전지에 비해 1sun 상 30% 이상의 고효율을 갖고 있고 앞으로도 계속 증가할 수 있는 가능성을 갖고 있다. 그 이유는 직접천이형 밴드갭, 높은 이동도 등의 고성능 물질특성과 더불어 3족과 5족의 비율을 조절함으로써 같은 결정구조를 갖고 에너지 밴드갭이 다른 물질들을 만들기에 용의하여, 태양전지 스펙트럼의 넓은 영역을 흡수할 수 있는 장점이 있기 때문이다. 그러나, 셀자체의 물질이 실리콘에 비하여 고가이므로, 고성능이 요구되는 우주 인공위성등에 적용이 되었지만, 2000년대 이후로 집광에 적용가능한 태양전지의 연구를 거듭하여 2005년부터는 값싼 프레넬 렌즈를 이용하여 1sun에 비해 500배 해당하는 빛을 셀에 집광하여 보다 효율을 증가시킴으로써 지상발전용에도 적용가능한 셀을 형성하게 되었다. 더불어 태양전지의 효율을 증가시키기 위한 개선된 구조적 변화의 시도도 많이 이루어지고 있다. 최근 보고에 의하면 실리콘 태양전지의 표면에 texture 또는 나노 구조를 주어 높은 흡수율과 낮은 반사율을 갖게 함으로써 효율을 증가시키는 사례가 많아지고, III-V 화합물 태양전지도 texturing에 의해 증가된 효율을 발표한바 있다. 본 연구에서는 태양전지의 효율을 증가시키기 위하여 III-V 화합물 태양전지 표면에 micro-hole array texture 구조를 형성한 후 나노 particle을 이용한 나노 texture 구조를 형성하였다. Photo-lithography와 chemical wet etching으로 micro-hole array texture 구조를 형성하였으며 micro-hole의 직경은 $5{\sim}20{\mu}m$, hole과 hole의 간격은 $3{\sim}15{\mu}m$로 다양하게 변화를 주었다. 형성된 micro-hole array texture 구조위에 수십 nm 크기의 particle을 만들어 chemical wet etching으로 나노 texture 구조를 형성하였다. 태양전지 표면에 texture 구조가 있는 경우와 없는 경우에 각각 효율을 측정, 비교 분석하였다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.376-377
• /
• 2011

결정질 실리콘 태양전지 연구에 있어서 가장 중요한 부분은 재료의 저가화와 공정의 단순화에 의한 저가의 태양전지 셀 제작 부분과 고효율의 태양전지 셀 제작 부분이다. 본 논문에서는 마이크로 블라스터를 이용하여 폐 실리콘 웨이퍼를 태양전지용 재생웨이퍼를 제작함으로써 고효율을 가지는 단결정 실리콘 웨이퍼를 저 가격에 생산하기 위한 것이다. 특히 마이크로 블라스터를 이용하여 폐 실리콘 웨이퍼를 가공 할 때 표면에 생성되는 요철은 기존 태양전지 셀 제작에서 텍스쳐링 공정과 같은 표면 구조를 가지게 됨으로써 태양전지 셀에 제작 공정을 줄일 수 있는 효과도 가지게 된다. 마이크로 블라스터는 챔버 내에 압축된 공기나 가스에 의해 가속 된 미세 파우더들이 재료와 충돌하면서 재료에 충격을 주고 그 충격에 의해 물질이 식각되는 기계적 건식 식각 공정 기술이다. 이러한 물리적 충격을 이용하는 마이크로 블라스터 공정은 기존 재생웨이퍼 제작 공정 보다 낮은 재처리 비용으로 간단하게 태양전지용 재생웨이퍼를 제작 할 수 있다. 하지만 마이크로 블라스터를 이용하면 표면에 식각된 미세 파티클의 재흡착이 일어나게 되므로 이를 제거하기 위하여 DRE(damage remove etching) 공정이 필요하게 된다. 본 연구에서는 이방성, 등방성 식각 공정으로 태양전지용 재생웨이퍼를 제작하기 위해 가장 적합한 DRE 공정을 찾기 위해 등방성 식각은 RIE 식각으로, 그리고 이방성 식각은 TMAH 식각을 이용하였다. 마이크로 블라스터 공정 후 표면 반사율과 SEM 사진을 이용한 표면 요철 구조를 확인 하였고, DRE 공정 후 표면 반사율과 SEM 사진을 이용하여 표면 요철 구조를 확인 하였다. 각각의 lifetime을 측정하여 표면 식각으로 생성된 결함들을 분석하여 태양전지용 재생웨이퍼 제작에 가장 적합한 공정을 확인 하였다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03a
• /
• pp.18-20
• /
• 2010

The mechanism for suppression of Ag agglomeration in Ag-Mg alloy ohmic contact to p-GaN is investigated. The Ag-Mg alloy ohmic contact shows low contact resistivity of $6.3\;{\times}\;10^{-5}\;{\Omega}cm^2$, high reflectance of 85.5% at 460 nm wavelength after annealing at $400^{\circ}C$ and better thermal stability than Ag contact The formation of Ga vacancies increase the net hole concentration, lowering the contact resistivity. Moreover, the oxidation of Mg atoms in Ag film increase the work function of Ag-Mg alloy contact and prevents Ag oxidation. The inhibition of oxygen diffusion by Mg oxide suppresses the Ag agglomeration, leading to enhance light reflectance and thermal stability.

• Journal of the Korean Vacuum Society
• /
• v.19 no.2
• /
• pp.114-120
• /
• 2010

Conventional surface texturing in crystalline silicon solar cell have been use wet texturing by Alkali or Acid solution. But conventional wet texturing has the serious issue of wafer breakage by large consumption of wafer in wet solution and can not obtain the reflectance below 10% in multi crystalline silicon. Therefore it is focusing on RIE texturing, one method of dry etching. We developed large scale plasma RIE (Reactive Ion Etching) equipment which can accommodate 144 wafers (125 mm) in tray in order to provide surface texturing on the silicon wafer surface. Reflectance was controllable from 3% to 20% in crystalline silicon depending on the texture shape and height. We have achieved excellent reflectance below 4% on the weighted average (300~1,100 nm) in multi crystalline silicon using plasma texturing with gas mixture ratio such as $SF_6$, $Cl_2$, and $O_2$. The texture shape and height on the silicon wafer surface have an effect on gas chemistry, etching time, RF frequency, and so on. Excellent conversion efficiency of 16.1% is obtained in multi crystalline silicon by RIE process. In order to know the influence of RF frequency with 2 MHz and 13.56 MHz, texturing shape and conversion efficiency are compared and discussed mutually using RIE technology.

• Journal of the Korean Vacuum Society
• /
• v.19 no.2
• /
• pp.141-147
• /
• 2010

In this study, high-k oxide films like $Al_2O_3$, $TiO_2$, $HfO_2$ were deposited on Si, $SiO_2$/Si, GaAs wafers, and then the thermal conductivity was measured by using thermo-reflectance method which utilizes the reflectance variation of the film surface produced by the periodic temperature variation. The result shows that high-k oxide films with 50 nm thickness have high thermal conductivity of 0.80~1.29 W/(mK). Therefore, effectively dissipate the heat generated in the electric circuit such as CMOS memory device, and the heat transfer changes according to the micro grain size.

• Korean Journal of Optics and Photonics
• /
• v.23 no.3
• /
• pp.124-127
• /
• 2012

We designed and fabricated dichroic filters for high-power fiber lasers to protect the pumping laser diode from counterpropagating laser beams. The transmittance at laser diode wavelengths of 905 nm~925 nm was designed to be less than 0.1% and the transmittance at the fiber laser or Brillouin scattering wavelengths of 1020 nm ~ 1100 nm was designed to be more than 99.9%. Since oxide materials have good adhesion to the $SiO_2$ substrate, $SiO_2/Ta_2O_5$ were used as coating materials. The filter was fabricated according to our optimized design and its characteristics were compared with the theoretical design. As a result, the transmittance at laser diode wavelengths of 905 nm~925 nm was measured to be less than 0.1%, and the transmittance at the fiber laser or Brillouin scattering wavelengths of 1020 nm~1100 nm was measured to be more than 95.5%, which coincided well with the theoretical design considering processing errors. The filter was found to operate well over 1W of input laser power.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.1
• /
• pp.7-11
• /
• 2010

The reduction of optical losses in mono-crystalline silicon solar cell by surface texturing is a critical step to improve the overall cell efficiency. In this study, we have changed the sub-micrometer structure on the micrometer pyramidal structure by 2-step texturing. The Ag particles were coated on the micrometer pyramid surface in $AgNO_3$ solution, and then the etching with hydrogen fluoride and hydrogen peroxide created even smaller nano-pyramids in these pyramids. As a result, we observed that the changes of size and thickness of nano structure on pyramidal surface were determined by $AgNO_3$ concentration and etching time. Using 2-step texturing, the surface of wafers is etched to resemble the rough surface of a lotus leaf. Lotus surface can reduce average reflectance from 10% to below 3%. This reflectance is less than conventional textured wafer including anti-reflection coating.

• Korean Journal of Remote Sensing
• /
• v.36 no.6_1
• /
• pp.1379-1391
• /
• 2020

UAV in the agricultural application are capable of collecting ultra-high resolution image. It is possible to obtain timeliness images for phenological phases of the crop. However, the UAV uses a variety of sensors and multi-temporal images according to the environment. Therefore, it is essential to use normalized image data for time series image application for crop monitoring. This study analyzed the variability of UAV reflectance and vegetation index according to Aviation Image Making Environment to utilize the UAV multispectral image for agricultural monitoring time series. The variability of the reflectance according to environmental factors such as altitude, direction, time, and cloud was very large, ranging from 8% to 11%, but the vegetation index variability was stable, ranging from 1% to 5%. This phenomenon is believed to have various causes such as the characteristics of the UAV multispectral sensor and the normalization of the post-processing program. In order to utilize the time series of unmanned aerial vehicles, it is recommended to use the same ratio function as the vegetation index, and it is recommended to minimize the variability of time series images by setting the same time, altitude and direction as possible.