• Elastomers and Composites
• /
• v.40 no.4
• /
• pp.242-248
• /
• 2005

To study the fatigue properties of three type of foams for footwear midsole, polyurethane(PU), phylon(PH) and injection phylon(IP) foams were prepared with different hardnesses. Three types of foams were repetitively compressed for 50,000 cycles at 50 rpm. Cell shapes of foams were deformed with repetitive compression. The extent of cell deformation of IP was larger than those of PH and PU. Permanent strain of foam was made by repetitively compressing the foam, and the extent of IP was larger than those of PU and PH. Maximum compression forces of three types of the foams were decreased with the repetitive compression, and IP had the largest decrease in compression load of foam with compression. Decreases in maximum compression force of three types of foams were increased with increase of the hardness of foam.

• Elastomers and Composites
• /
• v.47 no.2
• /
• pp.121-128
• /
• 2012

Waste EPDM(W-EPDM) collected from the automotive weather strip and the gasket of a laundry machine has not been effectively recycled. Using this W-EPDM powder and other ingredients, i.e., binder(polyolefin resin, polyolefin elastomer, etc.), filler and additives, various economic rubber composites were made by extrusion. In advance of main experiments, the effects of ultrasonic treatment of W-EPDM on the property of rubber composites, comparison in the property of the composites of W-EPDM with those of virgin and devulcanized EPDM, and waste tire rubber were investigated. Also, the properties of the rubber composites extruded with a 12-screw extruder were compared with those extruded with twin-screw extruder. Various W-EPDM composites for synthetic turf filler and car mat were extruded and injection molded, and 3 main properties of tensile strength, elongation and hardness were investigated to develop economical and proper recipes of the rubber composites.

• Elastomers and Composites
• /
• v.43 no.1
• /
• pp.8-17
• /
• 2008

Styrene-butadiene rubber(SBR) has good abrasion resistance, miscibility, and anti-vibration property. however, it is easily damaged by ozone and swelled by hydrocarbon fluids because of unsaturation part in main chain, that causes loss of visco-elasticity and reduction of product's life cycle. Therefore, object of this study is to cope with this problem. SBR is blended with various proportion of ethylene-propylene-diene terpolymer(EPDM), which has excellent ozone and oxygen resistance, to improve physical properties and ozone resistance, and diverse analytical techniques are used to measure morphology, glass transition temperature$(T_g)$, ozone-resistance, degradation temperature, static spring constant, hardness for considering a suitability for anti-vibration industrial product. We found that the blend consisting of SBR 70% and EPDM 30% showed no crack after ozone test and good miscibility between SBR and EPDM from this study.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.5
• /
• pp.549-556
• /
• 2010

In general, materials that can be used to form elastic pads, such as urethane and rubber, are often used in flexible forming processes by inserting the pads between a blank and flexible die for smoothing the forming surface that is formed by a reconfigurable die. In this study, the effects of the elastic pad on formability in the flexible forming process for sheet metals are investigated by performing numerical simulations. In the simulation, the hyperelastic material model is used, where the urethane elastic pads serve as elastic cushions. Case studies are carried out for elastic materials with different hardness values and thicknesses. The results are used to evaluate formability by comparing the configuration of the deformed blank and its major cross-sectional profiles. It is verified that the elastic pad used in the flexible forming process for sheet materials should be hard and that its thickness should be chosen appropriately.

• Elastomers and Composites
• /
• v.34 no.5
• /
• pp.391-398
• /
• 1999

Di-2-ethyl hexyl phthalate (DOP) and di-2-ethyl hexyl adiphate (DOA) were mixed with poly(vlnvl chlorides) [PVC] which have different degrees of polymerization (DP). Tensile strength, elongation, density, abrasion resistance, and hardness of these compounds were measured, High molecular weight PVC(DP 2500) was superior to that of DP 1300 for tensile strength, Hardness. But elongation and abrasion resistance of P1300 systems were better than those of P2500 systems. The densities of both systems were almost same. On the other hand, DOP Plasticized PVC was superior to DOA plasticized one for tensile strength, elongation, hardness. In cases of density, abrasion resistance, and flexual resistance, DOA systems were better than those of DOP systems.

• Elastomers and Composites
• /
• v.46 no.2
• /
• pp.132-137
• /
• 2011

In the present investigation, thermal aging behavior of H-NBR/NBR blend with various H-NBR content was investigated. Mixture of dicumyl peroxide and sulfur were used as a curing agent. The influence of the thermal aging of the H-NBR/NBR blends on the solid state properties such as tensile strength, elongation at break, hardness and abrasion resistance was investigated. Tensile strength was increased with increasing H-NBR content, while abrasion resistance was decreased. Both elongation at break and hardness were not affected by the addition of H-NBR. The properties such as hardness, tensile strength and elongation at break of the aged samples were lower than unaged samples. However, the rate of deterioration of those properties was decreased by increasing the H-NBR content, which indicated that improved thermal aging behavior was obtained by the addition of H-NBR. Abrasion loss was increased with increasing aging time, but it became less by the addition of H-NBR addition.

• Elastomers and Composites
• /
• v.44 no.4
• /
• pp.455-465
• /
• 2009

In this study, Organo-montmorillonite(MMT) was synthesized by intercalation of various amine(Octylamine, Dodecylamine, Dimethyldodecylamine, Octadecylamine) compounds into layered silicate. Natural Rubber(NR)/MMT nanocomposites were prepared by reinforcement of Organo-MMT. X-ray diffraction(XRD) and Scanning electron microscope(SEM) were employed to characterize the layer distance of Organo-MMT and the morphology of the NR/MMT nanocomposites. The structures of the synthesized Organo-MMTs were analyzed by the measurement of FT-IR. Cure characteristics, surface free energy and mechanical properties such as tensile strength, modulus and hardness of NR/MMT nanocomposites were carefully studied by contact angle meter, ODR, UTM, and hardness tester. FT-IR analysis showed a insertion of the alkyl and amine chains into the interlayers of the MMT. It was shown that the cure time of the organo-MMT was more decreased than that of $Na^+$-MMT. Surface free energy and tensile strength of the NR/DDA-MMT nanocomposite were the highest. NR/ODA-MMT nanocomposite was the highest in hardness.

• Korean Journal of Agricultural Science
• /
• v.5 no.2
• /
• pp.127-135
• /
• 1978

For improvement and new design of tillage equipments, indoor test is very useful and more desirable than outdoor because the experiment of outdoor is very difficult and its cost is expensive. This study was carried out to determine the physical properties of artificial soil suitable for the indoor test with the soil bin manufactured at the workshop of the Dept. of Agricultural Machinery Engineering. The artificial soil being studied was made with very similarity to the natural soil of the experimental plots of Chungnam National University, and it consist of 39.35 percent, by weight of bentonite and 48.10 percent of sand with 12.55 percent of SAE 10W oil. The results are summarized as follows: 1. Bulk density increased with increasing number of rolling, and its relationship could be expressed. $y=1.073200+0.070780x-0.002263x^2$ where, y=bulk density ($g/cm^3$), x=number of rolling. These results could be explained that the effect of rolling velocity on the bulk density was not singnificant in the range of 4.5~10.4 em/sec. 2. The absolute soil hardness depended directly upon number of rolling, and their relationship could be expressed by the equation. $y=37.74(0.64 +0.17x-0.0054x^2)/(3.36-0.17x-0.0054x^2)^3$. where, y=absolute soil hardness($kg/cm^3$), x=number of rolling. 3. Relationship between the bulk density and absolute soil hardness could be expressed by the equation; $y=37.74(2.46x-2.02)/(6.02-2.46x)^3$. where, y=absolute soil hardness, x=bulk density. 4. The cohesion and the angle of internal friction of artificial soil were increased with increasing its bulk density. According to the cohesion and angle of internal friction, at the range of 1.60~1.75 ($g/cm^3$) of bulk density, this artificial soil was similar with sandy loam of 29.5% moisture content of natural soil. 5. Sliding-fricfion coefficient of steel plate on the artificial soil was 0.3~0.4 and rubber plate on it is 0.64~0.72. Those values were very similar with those of natural soil being studies by many others.

• The Korean Journal of Rheology
• /
• v.9 no.1
• /
• pp.33-39
• /
• 1997

PCL, MDI, BD 및 DMPA를 이용, 폴리우레탄(PU)을 ionomer 및 nonionomergudxo 로 제조하였으며 이때 연질성분의 함량(SSC) 및 길이가 PU의 기계적, 동적기계적 특성은 물론 형상기억특성에 미치는 영향을 연구하였다. Ionomer는 nonionomer에 비하여 경도, 탄 성율 및 강도가 모두 우수하였으며 그 효과는 실온에서 경질성분의 함량(HSC)이 높은 PU 일수록 보다 뚜렷하였는데 이는 HSC가 증가할수록 ion 중심의 농도가 증가하며 ion 중심간 의 Coulob 력이 고온보다 실온에서 보다 큰데 기인하는 것으로 해석하였다. 반복인장하중실 험에서 ionomer는 nonionomer에 비해 회복변형이 크고 잔류변형이 작았는데 이는 ionomer 의 고무탄성율이 보다 큰 데 기인한 것으로 해석하였다. 나아가 재료의 형상기억거동은 기 본적으로 탄성율의 온도의존성에 크게 의존함을 알수있었다.

• Elastomers and Composites
• /
• v.48 no.3
• /
• pp.241-248
• /
• 2013

Polyester type polyurethane foam has low hydrolysis resistance. It was overcome with addition of acrylic polyol by quasi prepolymer method. Tensile strength and hardness of polyurethane foam contained acrylic polyol was increased with increasing of acrylic polyol contents. But split tear strength and tear strength was slightly changed. Hydrolysis resistance of polyurethane foam was measured by loss % of tensile strength. It was improved with increasing of acrylic polyol contents from 25.5g to 102g.