• Journal of Adhesion and Interface
• /
• v.14 no.3
• /
• pp.128-134
• /
• 2013

This study investigated the natural adhesives for ceramics conservation that can be used as a substitution for synthetic resins. Samples were prepared by mixing lacquer with animal glue and the structure and adhesion properties of the samples were analyzed. The structure analysis with FT-IR showed that carbonyl (C=O), amine (N-H) and aromatic (C=C) bonds are increased by adding animal glue on lacquer. Comparing to the viscosity and tensile strength of the sample to the Paraloid B-72 and Araldite rapid type, these natural adhesives can be a substitution for the synthetic resins. Through methodical and intensive study, we expect practical uses of this eco-friendly natural adhesives for ceramics conservation.

• Journal of Adhesion and Interface
• /
• v.17 no.1
• /
• pp.1-6
• /
• 2016

In this study, to replace a complicated process such as in the rubber component used in the adhesive of the shoe buffing, pretreatment with primers, we studied mechanical properties and adhesive properties with rubber compound added propanamine and 1,6-Hexanediamine. The adhesive properties rubber specimen added propanamine did not occurrence, but The adhesive properties rubber specimen added 1,6-Hexanediamine was occurrence. Also, the contact angle was decreased compared to not added NBR. And rubber compound added 6-Hexanediamine was smaller than the contact angle was evaluated in comparison to the added propanamine. $NH_2$ group on the rubber surface were confirmed with a peak at $1450{\sim}1550cm^{-1}$ in FT-IR spectrum. Rubber compound added propanamine and 1,6-Hexanediamine was reduced mechanical properties and decreased NBS resistance.

• Composites Research
• /
• v.23 no.6
• /
• pp.32-38
• /
• 2010

The effect of the atmospheric pressure plasma(APP) treatments is experimentally investigated to ascertain the optimum condition to yield the best adhesive properties between a polyamide woven fabric and acrylonitrile butadiene rubber(NBR). For the atmospheric pressure flame plasma(APFP) treatment, the optimum number of treatment at given conditions is 2 times. The thermal deformation of the fabric is more serious with increasing the number of APFP treatment. The adhesive strength of the case with APFP treated fabric is increased about 35% when compare to the case with non-APFP treated one for the interface(bonding agent one or two coatings). When the surface is coated twice with the bonding agent, the adhesive energy with APFP treated fabric is increased about 4 times. It was found that the surface modification of polyamide woven fabric by APFP treatment is a fast, economic and applicable method to improve the adhesive properties between woven fabric and rubber when compared to other APP treatments.

• Journal of Adhesion and Interface
• /
• v.13 no.1
• /
• pp.1-8
• /
• 2012

The effect of the grafting ratio on the mechanical property and adhesion property of the grafted EPDM modified with methacrylic acid (MA) was investigated. The storage modulus of MA-grafted EPDM was maintained higher than that of cross-linked EPDM vulcanizate by sulfur, but it was observed that the storage modulus was decreased at elevated temperature because of the weakened secondary bonding. When the functional group for hydrogen bonding was introduced in EPDM, it had excellent mechanical properties by the aggregate between grafted EPDM molecules and crystallinity of MA. The bonding strength between EPDM and other rubbers was very low because EPDM has nonpolar property and low molecular interaction to others. The bonding strength was increased as increasing grafting ratio and it was excellent enough to break the rubber during the peel test when the grafting ratio was more than 10%.

• Journal of Adhesion and Interface
• /
• v.19 no.2
• /
• pp.55-59
• /
• 2018

In this study, to overcome a complicated shoe adhesion process such as buffing, pre-treatment by primer in the rubber component of the shoe, we studied adhesion mechanical properties with rubber compound added water-soluble salt for the purpose of improving the adhesion between midsole and outsole. Acid salts, basic salt and neutral salts were evaluated, rubber containing basic salts showed excellent adhesion to water-based adhesion. Since the basic salt is present as the hydroxy salt, the surface of rubber is hydrophilized. The results are confirmed by contact angle and IR spectroscopy measurement. In addition, in the case of rubber compound added basic salts, NBS abrasion resistance and hardness were increased by increasing crosslink density, but crosslink time was delayed.

• Journal of Adhesion and Interface
• /
• v.21 no.1
• /
• pp.27-33
• /
• 2020

Adhesion property of epoxy adhesive was evaluated with different surface roughness of glass fiber reinforced composite (GFRC) and optimized condition of surface roughness was confirmed. Different sizes of alumina (Al2O3) particles were blasted to GFRC to control surface roughness of GFRC using sand blasting method. The surface roughness was measured and quantified via surface roughness tester. Contact angle was measured using four types of different solvents. Surface energies and work of adhesion between epoxy adhesive and GFRCs were calculated with different surface roughness of GFRC. Adhesion property between epoxy adhesive and GFRCs was evaluated using single lap shear test and adhesion property increased with surface roughness of GFRC. The fracture surface of GFRCs was observed to evaluate adhesion property. Finally, the optimized roughness condition of GFRCs was confirmed.

• Journal of Adhesion and Interface
• /
• v.15 no.2
• /
• pp.49-56
• /
• 2014

In this study, properties of adhesion between adhesion promoter-containing rubber compound and zinc coated steel cord was investigated. Cobalt salt, resorcinol formaldehyde resin (RF resin) and hexamethoxymethylmelamine (HMMM) were used to adhesion promoter. Since cobalt salts accelerate sulphidation rate of zinc at zinc coated steel cord surface, pullout force of rubber compound applying cobalt salts was increased compared to that of rubber compound without applying cobalt salts. Pullout force and rubber coverage of rubber compounds applying all adhesion promoters were superior because strong interlocking between rubber matrix increased modulus due to applying RF resin and HMMM and grown zinc sulfides at zinc coated steel cord surface.

• Journal of Adhesion and Interface
• /
• v.24 no.3
• /
• pp.105-111
• /
• 2023

Recently, there has been a growing interest in low biofouling coatings for various industrial applications including precious metal and jewelry applications. Contaminations including cells and bacteria of the metallic substrates (i.e., accessories, earring, and piercings) may irritate the contacted tissue surfaces or induce an abnormal reaction. In this study, catechol-conjugated polyethylene glycol (PEG-C) was synthesized as low bio-fouling coating materials inspired by mussel-adhesion. PEG-C-coated copper-zinc alloy surfaces showed excellent cell viability and significant inhibitions of protein and cell adhesions to metal surfaces. Thus, PEG-C coating methods and PEG-C-coated metallic substrates can be usefully exploited for versatile industrial applications, particularly for precious metal and jewelry industries.

• Journal of Adhesion and Interface
• /
• v.18 no.4
• /
• pp.159-165
• /
• 2017

In this study, we synthesized UV-curable urethane acrylates with different contents of BA, reactive diluent and characterized their physical properties such as thermal, mechanical properties, adhesive strength and flexibility resistance. From a result of DSC, Tg of polyol and acrylate resin were separated as the BA content increased more than 40%. Also, tensile strength, elongation and adhesive strength decreased with increasing the BA content. The UV-curable urethane acrylate with 40% BA has shown good flexibility resistance compared to other resin due to poor hardness and Tm of acrylate resin.

• Journal of Adhesion and Interface
• /
• v.9 no.4
• /
• pp.12-16
• /
• 2008

Hot-melt adhesive was solid phase in room temperature as 100% solid contents. So it has advantage which attach to substrate with the low pressure heat, fast adhesion speed and environment friendly. In this study, We studied about the effect of a kind of SBS resin and petroleum resin as a tackifier resin and their ratio for hot-melt adhesive on properties. The styrene and $C_9$ resin contents in hot-melt adhesive was increased with increasing viscosity, tensile strength, peel strength and thermal resistance.