• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.223-226
• /
• 2007

본 연구에서는 Ag anisotropic conductive adhesive(ACA)의 종류, 경화 조건 및 안테나 패턴의 재질에 따른 flip chip bonding된 RFID die의 접합부 신뢰성이 조사되었다. 접합강도 측정에 의하여 접합강도가 최적화되는 공정 시간을 결정할 수 있었으며, 그러한 최적의 공정조건에서는 paste-type Ag ink로 인쇄된 안테나 상에서의 RFID die의 접합강도가 Cu 재질 안테나에 비해 상대적으로 높게 측정됨을 알 수 있었다. RFID tag의 인식거리 측정 시험을 통하여 적절한 경화 조건이 적용된다면 안테나의 재질이 인식거리 변화에 가장 주요한 영향을 미치는 인자임을 알 수 있었다. 아울러 Cu 안테나 패턴은 RFID die의 접합 과정에서 곡률을 가지며 휘어지면서 인식거리와 관련된 long-tem reliability를 악화시킬 수 있음을 관찰할 수 있었다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.1
• /
• pp.37-42
• /
• 2016

In this study, we examined the burning rate of the uncured propellant (with and without a curing agent application) in order to inspect the process of the HTPB solid propellant. The burning rate of the uncured propellant, that did not contain the curing agent, was approximately 9.7 mm/s at 1000 psi. In relation to the curing time, the burning rate was constant. The propellant, with the curing agent application, was approximately 8.1 mm/s showed a tendency of slowing as it burned. When the cure reaction rate was low, in accordance to the time, there were small changes in burn rate. However, when the cure reaction rate was high, the difference in burning rate was increased. The burning rate of a fully-cured propellant was approximately 6.8 mm/s, which appeared to be the lowest in order.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.413-416
• /
• 2005

The study has been performed on the improvement of bonding process and bond strength of HTPB propellant and liner using a polymeric curative. In case of liner using polymeric curative prepared from reaction of HTPB and TDI, migration of curative was decreased at bond interface. So EPDM insulation sanding and Desmodur RE coating process could be omitted in motor case preparation and bond strengths between the HTPB propellant and liner were increased. Also deterioration phenomena of bond strength could not be observed in accelerated aging test.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.10 no.2
• /
• pp.110-114
• /
• 2006

The study has been performed on the improvement of bonding process and bond strength of HTPB propellant and liner using a polymeric curative. In case of liner using polymeric curative prepared from reaction of HTPB and TDI, migration of curative was decreased at bond interface. So EPDM insulation sanding and Desmodur RE coating process could be omitted in motor case preparation and bond strengths between the HTPB propellant and liner were increased. Also deterioration phenomena of bond strength could not be observed in accelerated aging test.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.92-92
• /
• 2008

PDP의 저가화, 친환경화, 고화질화는 타 디스플레이와 경쟁을 위해 필수적이고 그로 인한 소재의 개발이 필요하다. 저가화는 부품, 공정에서도 가능하지만 소재에서의 원가가 상당부분을 차지하고 있기 때문에 소재 개발이 중요하며, 친환경화는 현재 유전체에서 많이 사용되고 있는 유해소재를 친환경 소재로 대체함으로써 개발이 이루어지고 있다. 그래서 우리는 현재 PDP에서 전극물질로 사용되어지는 고가의 Ag를 Gu입자에 Ag 박막으로 코팅한 Ag/Cu 전극 powder를 사용하여 저가의 전극 paste를 만들고 스크린 프린터와 노광장비를 사용하여 전극을 형성하였다. 그 후 친환경적인 Pb free 투명유전체를 입히고 전극과의 상호 매칭성을 연구 하였다. 결과적으로 기존 PDP 공정에서 볼 수 없었던 황변현상, 전극착색현상, 전극입자의 터짐성 등 많은 현상이 일어났지만, 기존 공정 온도보다 낮은 온도로 공정한 결과, 이러한 문제들이 줄어드는 것을 확인하였다. 이로써 공정단가의 저가화와 제품의 친환경을 가면서도 기존과 차이가 제품을 실현할 수 있을 것이다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.2
• /
• pp.119-124
• /
• 2013

In this study, the two-dimensional transient temperature of printed Ag nanoparticle ink during continuous wave laser sintering was calculated. Ag nanoparticle ink was printed on a glass substrate by inkjet printing. Then, a 532-nm continuous wave laser with different laser intensities was irradiated on the printed Ag nanoparticle ink for 60 s. During laser irradiation, the in-situ specific resistance of the sintered ink was measured. To obtain the transient temperature of the sintered ink during the laser sintering process, a two-dimensional transient heat conduction equation was derived by applying the Wiedemann-Franz law. It was found that the specific resistance of the sintered ink decreased with an increase in the sintering temperature of the printed ink.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.443-450
• /
• 2021

The effects of blast furnace slag(BFS) and desulfurized gypsum(FDG) on the compressive strength of CFBA, and self-hydration of CFBA were studied. CFBA has self-hydrating and hardening properties, and it can be seen that the compressive strength of CFBA can be improved by using appropriate amounts of BFS and FDG. In addition, the self-hardening properties of CFBA are similar to the hydration reaction of 4CaO·Al₂O₃·Fe₂O₃ (C₄AF), a cement clinker mineral, and when free-CaO, CaSO₄ and CaCO₃ coexist, Compressive strength of CFBA is expressed by the formation of calcium carbo compounds and hydrates of ettringite, calcium silicate, and calcium aluminate.

• Journal of Adhesion and Interface
• /
• v.19 no.2
• /
• pp.74-82
• /
• 2018

Many methods for cross-linking acrylic PSAs have been discussed previously. For high cross-linking density, epoxy functionalized monomer and methyl aziridines as cross-linking agents were used in this study. Additionally, photopolymerization using different UV doses was investigated to synthesize a binder because of its rapid productivity. FT-IR analysis, curing behaviours and adhesion performance were examined for the relationship between UV doses and temperature as curing conditions. According to the results, the gel fraction was over 50% even at $120^{\circ}C$ after UV curing at a dose of $800mJ/cm^2$. On the other hand, while gel fractions of all samples reached approximately 80% only at $180^{\circ}C$ in thermal curing for 1 hour, gel fractions of the samples after thermal curing for 3 hours increased rapidly above $120^{\circ}C$ regardless of UV doses and reached approximately 100% at $180^{\circ}C$. This means that the second cross-linking reaction, esterification, is mainly dependent on the curing temperature.

• Nuclear industry
• /
• v.17 no.11 s.177
• /
• pp.68-77
• /
• 1997

• Composites Research
• /
• v.37 no.1
• /
• pp.15-20
• /
• 2024

Since the residual stress of hydrogen tank is directly related to durability, it is very important to reduce it for safety. Type II~IV hydrogen tank are manufactured by the filament winding method, in which the fiber is impregnated with resin and wound around the liner. Residual stress in composite is affected by curing conditions and fiber tension etc. In this study, the effect of curing conditions on residual stress was analyzed when manufacturing a Type III hydrogen tank using carbon fiber filament winding process. First, the curing behavior of the epoxy resin was analyzed using a differential scanning calorimetry. Through this, the curing temperature was set to 140℃. During the same curing time, the specimens were cured under 2-stage curing condition that reached 140℃ earlier and a 4-stage curing condition that reached 140℃ later, respectively. After curing, the residual stress of the composite material was measured by the ring slitting method, and the experimental values were compared with numerical values. It was confirmed that there was a significant difference in residual stress according to the optimization of curing conditions.