• Journal of the Korean Institute of Gas
• /
• v.10 no.3 s.32
• /
• pp.27-33
• /
• 2006

This paper investigates leak effect on the outlet pressure at pipeline exit. A modified Weymouth equation(including inclination effect) was used for this study. To investigate leak effect, outlet pressure and ratio of outlet to inlet pressure were compared between no leak and leak conditions for horizontal, upward and downward flows, respectively. Then, effects of leak location as well as leak rate on the outlet pressure were also investigated for all pipeline inclinations.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.28-28
• /
• 1998

단일 충돌제트의 경우 충돌면에서의 열전달 효과는 제트 출구와 충돌면 사이의 간격, 노즐 형상에 따른 제트출구의 초기조건, Re$_{D}$수 변화와 충돌면의 형상이나 표면거칠기 등에 따라 변화하게 된다. 그러나 수직 충돌제트의 경우 정체영역에서의 국소적인 열전달 향상은 용이하나 반경 방향으로 열전달이 점차 감소하게 된다. 따라서 충돌면의 전반적인 열전달 향상을 위해서는 열전달이 정체점보다 상대적으로 낮은 영역에서 열전달 향상이 필요하다. 또한, 실제 적용시 충돌면의 형상이나 협소한 공간에서 노즐위치의 제약으로 인하여 충돌제트가 수직으로 분사되는 경우보다 경사진 제트가 더욱 많이 응용된다. 더욱이, 수직충돌제트가 사용되는 많은 상황에서도 주위의 다른 공기 흐름의 영향으로 인하여 실제 제트가 경사각을 갖고 분사되어진다 이러한 경사충돌제트의 중요성에도 불구하고 경사충돌제트에 대한 연구는 수직충돌제트에 대한 연구보다 상대적으로 적게 이루어져 왔다.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.134-137
• /
• 2014

The noise reduction performance of a passive facility is dependent on the its length or volume. In other words, this means that the larger the size of passive facility is, the better the noise reduction performance is. The sound directivity control has been proposed as an alternative for the noise reduction without a passive facility. The purpose of this study is to investigate the correlation between the flange attached to inclined exit of the tube and sound directivity when the sound radiates from the tube to the outside. As a result, the sound radiated from flanged tube had weak sound directivity in the wide angle. Also as the flange was bigger, the sound pressure level was lower in the behind the flange.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.618-621
• /
• 2014

This research is to review the possibility of reducing the noise radiated from the tube exit by controling the sound reflection coefficient at the inclined exit. The sound reflection coefficient at the inclined exit of flanged tube was measured by both transfer function method and standing wave ratio method. Accuracy on the sound reflection coefficient measured by transfer function method was verified through comparison with sound reflection coefficient measured by standing ratio method. The flanged tube had lower sound reflection coefficient than the tube which have no flange. Also the sound reflection coefficient was decreased in accordance with increasing the inclined angle of unflanged tube.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.7 no.3
• /
• pp.175-181
• /
• 2003

In this reseach, a seepage test is carried out for three kinds of soil using a upward seepage equipment. Reliability about the existing method of pipining investigation were verified making an estimate of the critical velocity, the critical hydraulic gradient, and hydraulic conductivity and so on. Also, sensitive analyses were carried out using Plaxis that is FEM Program about design factors of scour. The height of core had a big infulence on the hydraulic gradient of the embankment's lower part in the result of sensitive anaylsis. Also, second only to the height of core, and the slope of embankment, the width of crest had influence on scour. However, the change of hydraulic gradient in the effluent gateway had a little influence on the crest width of core. Using these results of sensitive analysis on designing, hydraulic gradient in the effluence gateway turned out to be reducing by altering design factors that change of sensitiveness is big, in case of the hydraulic gradient bigger than the standard hydraulic gradient.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2017.11a
• /
• pp.232-233
• /
• 2017

In this research, tunnel stern was applied on the asymmetric high-speed catamaran to evaluate vessel's hydrodynamic performance by numerical method, and the tunnel stern types are distinguished by angle of inclination of tunnel exit region into 3cases ($0^{\circ}$, $3^{\circ}$ and $6^{\circ}$). Consequently, it is confirmed that the total resistances of tunnel stern which have $0^{\circ}$ of inclination are lower about 4.8-17.9% than the bare hull in the wide speed range, but those of $3^{\circ}$ and $6^{\circ}$ of inclination tunnel stern are higher than bare hull about 5-14% and 5-29%, respectively. On the other hand, trim angles of $0^{\circ}$ of inclination tunnel stern show similar trend with those of bare hull in whole ranges of FnV but those of $3^{\circ}$ and $6^{\circ}$ of inclination tunnel stern are stabilized and declined respectively after FnV=1.54. These phenomena indicated that increasing angle of inclination of tunnel exit region had negative influence on resistance performance, however, it could make vessel's operation performance better than bare hull.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.2 no.2
• /
• pp.3-10
• /
• 2000

The compression wave produced when a high-speed train enters a tunnel propagates along the tunnel ahead of the train. The micro pressure wave related to the compression wave is a special physics phenomena created by high-speed train-tunnel interfaces. A among methods for the purpose of reducing the micro pressure wave is to delay the gradient of the compression wave by using aerodynamic structures. The objective of this paper is to determine the optimum slanted portal using the moving model rig. According to the results, the maximum value of micro pressure wave is reduced by 19.2% for the $45^{\circ}$ slanted portal installed at the entrance of the tunnel and reduced by 41.9% for the $45^{\circ}$ slanted portals at the entrance and exit of the tunnel. Also it is reduced by 34.6% for the $30^{\circ}$ slanted portals installed at the entrance and exit of the tunnel.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.32-32
• /
• 1999

초음속 과소 팽창 제트가 경사진 평판에 충돌을 하게 되면 평판의 표면과 노즐출구에서 팽창된 자유제트(Free jet)와의 상호 간섭으로 인해 매우 복잡한 유동 구조가 형성된다. 예를 들면, 수직평판에서 발생되는 판 충격파(Plate shock)는 경사평판에서는 Upper plate shock, Lower plate shock, Intermediate plate shock과 같이 여러 형태로 발생되어 평판에서의 압력분포에 있어 수직일 경우와 다소 다른 경향을 보여준다. 본 연구의 주요 목적은 평판의 경사각을 변화시킬 때 평판 표면에서의 복잡한 유동 현상을 이해하는데 있다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.1191-1195
• /
• 2010

도달시간 또는 집중시간이란 어떤 유역에 강우가 발생하였을 때 유역의 최상류부에서 내린 강우가 유역의 최하류부 출구점까지 도달하는 데 소요되는 시간으로 정의된다. 일반적으로 유역출구점에서의 첨두홍수량은 도달시간만큼 지체되어 발생하고, 하천의 치수 시설물을 설계하는데 있어 기준이 되므로 정확한 홍수도달시간의 산정은 매우 중요한 과업 중 하나이다. 현재 국내에서는 Kirpich 공식, Rziha 공식, Kraven 공식, SCS(NRCS; Natural Resources Conservation Service) 공식 등을 이용하여 도달시간을 산정한 후 그 유역에 적절한 것을 채택하는 방식으로 홍수도달시간을 산정하고 있다. 이러한 경험식들은 모두 유역의 지배적인 유로의 연장과 하도경사에 의해 결정되어 홍수의 이동특성을 물리적으로 반영할 수 없으며, 유역면적이나 하도 경사에 따라 적용성이 한정되어 있다. 또한 각 경험식들에 따라 산정된 도달시간은 경우에 따라 수십 배의 차이가 나타날 수도 있다, 따라서 본 연구에서는 보다 정확한 유역의 홍수도달시간을 산정하기 위하여 상세 지형정보를 이용하며, 임의의 격자점에 내린 강우의 흐름방향을 결정하고 인접 격자점에서 유입되는 홍수의 이동경로를 보다 물리적이고 현실적으로 모의하고자 하였다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.6
• /
• pp.1-9
• /
• 2021

In machining operations, a burr is an undesirable material formed by plastic deformation in a workpiece. With the ongoing industrial developments, it has become an important issue to efficiently remove burrs. Several deburring methods have been developed to remove specific burrs that require special machining. However, to remove burrs formed while machining at the CNC machining center, deburring tools must be developed. In a previous study, a new deburring tool was developed by the authors. In this study, the influence of the rake angle and stiffness of the new deburring tool was analyzed to improve performance. The theoretical model was driven considering the rake angle and stiffness, and experiments were carried out to validate the model. Especially, conditions based on the designed rake angle and stiffness to effectively remove burrs, which is difficult, at the exit surface were suggested.