• Proceedings of the Korean Society of Coastal and Ocean Engineers Conference
• /
• 1998.09a
• /
• pp.143-148
• /
• 1998

경사면 쇄파특성의 도출을 위한 기존의 연구는 주로 실험에 의존하여 왔다. 이들 실험적 연구들은 주로 임의 경사면에서 쇄파가 발생하는 수심과 쇄파고를 산출하는데 목적을 두었으며, CERC(1984)는 이들의 연구결과를 위합하여 쇄파제원을 산출할 수 있는 도표를 제시하였다. 본 연구에서는 수치조파경계와 천해 경사면으로 구성되는 파동장에서 경사면 쇄파거동에 대한 경계요소기법을 직접 수립하여 기법의 적용성을 세부적으로 고찰하기로 한다. (중략)

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.1
• /
• pp.173-178
• /
• 2020

A multi-ray model has been used to interpret radio transmission losses in half-canyon structures with slope and to formulate a multi-ray propagation model depending on the angle of slopes. The cut-off angles for the third and fourth paths, which are the slope-sided reflection paths of the transmission and reception radio waves determined by the inclined angles of the slope, were calculated with the height and location of the transmitter and receiver. To predict transmission losses in an inclined plane environment, the embankment environment where the actual slope exists was modeled and simulated to calculate the loss of propagation transmission, and the radio wave transmission loss was confirmed by the measurement for the frequency band 1 to 6 GHz. Simulation results and measurement results showed similar trends in radio transmission loss, and radio transmission loss predictions and measurement results for various terrain information can be used in the design of radio propagation service.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.34-40
• /
• 1999

An experimental study has been conducted to determine the effects of inclined impinging jet on the local heat transfer coefficients. A single jet with nozzle diameter of 24.6 mm was tested for Reynolds numbers from 10,000 to 70,000 and nozzle-to-plate spacings of 2~6 jet diameters. The angle of inclination of the impingement surface relative to the horizontal surface was varied from $0^{\cire}$ (normal impingement) to $60^{\cire}$. The results indicate that the point of maximum heat transfer is moved up from the geometrical stagnation point of inclined surface by Coanda effect. The local heat transfer coefficients on the minor jet region decrease more rapidly than on the major jet region, thus creating an imbalance in the cooling capabilities on the two sides.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.9 no.5
• /
• pp.57-62
• /
• 2009

Flame spread velocity to virgin surface fuel bed on a ground slope increases as the flame gets closer to the slope according to the change of a ground slope angle. The existing studies have generally adopted the theory that flame gets closer to the slope as the slope angle increases, without considering the change of flame tilt against the slope. In this study, experiments were made on the actual characteristics of the flame on slopes of various angles, and as a result, this study offers the flame tilt equation according to the slope angle, and derive correlation between flame tilt and flame spread velocity on slope conditions.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.11
• /
• pp.1665-1674
• /
• 2013

In this paper, we propose a genetic algorithm(GA) based locomotion method of a quadruped robot with waist joint, which makes a quadruped robot walk on the slop efficiently. In the proposed method, we first derive the kinematic model of a quadruped robot with waist joint and then set the gene and the fitness function for GA. In addition, we determine the best attitude for a quadruped robot and the landing point of a foot in the walk space, which has the optimal energy stability margin(ESM). Finally, we verify the effectiveness of the proposed method by comparing with the performance of the previous method through the computer simulations.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.116-116
• /
• 2003

• Proceedings of the Korea Water Resources Association Conference
• /
• 2004.05b
• /
• pp.484-489
• /
• 2004

경사식 방파제에 대하여 수리모형실험을 통하여 방파제의 전사면과 저면에 작용하는 파압을 직접 측정하여 파압의 공간적 분포를 파악하여 보았다. 실험의 길과는 기존의 경사식 방파제에 대하여 파압에 대한 연구는 거의 없기 때문에 Goda(1989, 2002)가 제시한 전사면에 대한 이론식과 비교하여 보았다. 실험은 특정적으로 제시된 방파제 단면에 대한 실험이 아니고, 가상적인 단면을 선정한 후 파랑 및 수심 등의 제조건을 감안하여 파형경사를 산정하고, 이애 맞는 파고와 주기를 산정한 후 제반 해안수리학적 특성중 반사율과 처오름 높이, 사면 및 저면에 작용하는 파압을 직접 측정하여 보았다. 실험결과 전사면에서의 파압 분포는 Goda의 이론식과 경향은 비슷하나 크기는 차이가 나이에 대한 보정은 필요한 것으로 나타났으며, 저면에서의 파압도 측정이 되었지만 이것이 지반지지력에 어떠한 영향을 미치는지는 좀 더 많은 연구가 필요할 것으로 판단되었다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.28-28
• /
• 1998

단일 충돌제트의 경우 충돌면에서의 열전달 효과는 제트 출구와 충돌면 사이의 간격, 노즐 형상에 따른 제트출구의 초기조건, Re$_{D}$수 변화와 충돌면의 형상이나 표면거칠기 등에 따라 변화하게 된다. 그러나 수직 충돌제트의 경우 정체영역에서의 국소적인 열전달 향상은 용이하나 반경 방향으로 열전달이 점차 감소하게 된다. 따라서 충돌면의 전반적인 열전달 향상을 위해서는 열전달이 정체점보다 상대적으로 낮은 영역에서 열전달 향상이 필요하다. 또한, 실제 적용시 충돌면의 형상이나 협소한 공간에서 노즐위치의 제약으로 인하여 충돌제트가 수직으로 분사되는 경우보다 경사진 제트가 더욱 많이 응용된다. 더욱이, 수직충돌제트가 사용되는 많은 상황에서도 주위의 다른 공기 흐름의 영향으로 인하여 실제 제트가 경사각을 갖고 분사되어진다 이러한 경사충돌제트의 중요성에도 불구하고 경사충돌제트에 대한 연구는 수직충돌제트에 대한 연구보다 상대적으로 적게 이루어져 왔다.

• Journal of Korea Water Resources Association
• /
• v.35 no.6
• /
• pp.779-786
• /
• 2002

A boundary element method with a Lagrangian approach and B-spline technique is employed to investigate characteristics of solitary waves attacking on beach slopes. By comparing numerical solutions with available laboratory measurements, it is shown that the maximum run-up heights of the present model are more agreeable than those of the existing numerical model. Variations of run-up heights and velocity vectors for different slopes are also described. Characteristics of hydrodynamic pressure acting beach slopes are investigated in detail.

• Journal of Korea Society of Industrial Information Systems
• /
• v.5 no.1
• /
• pp.77-86
• /
• 2000

Even manual materials handling tasks(MMHT) is decreasing by adopt of automatic manufacturing system & transportation supporting machine because of increase of productivity, wage lack of labor, safety, in fact working at inclined & complicated slope such as farm, orchard, harbor loading & unloading, logging place and mining place can't be substituted by machine perfectly. So, workers should do MMHT at this place by themselves, lifting on slope can cause much of hazard, include falling. Keeping balance net to slip can be a reason of low back pain(LBP) by overloaded musculoskeletal system but, there's no enough study about lift on slope. Therefore, In this study, we assessed and analyzed change of center of pressure(COP) when lifting on slope by force platform. The result showed that the length lengthen as increasing angle of slope. Especially, the length extremely increased over 15°. Through These basic result, present proper angle boundary, prevent industrial accidents and give proper data not only lifting but also pushing and pulling on slope someday.