• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.2
• /
• pp.286-291
• /
• 2011

Directional couplers are widely used in RF and microwave applications to distribute or monitor signals. This paper presented a new structure of microstrip branch line directional coupler with coupled lines. The loose couplings of microstrip branch line directional couplers are impractical for the high characteristic impedance values required for the shunt branches. To overcome this limitation, the parallel coupled lines with the shorts were used for the high characteristic impedance. The results of the simulations and measurements were presented for the proposed branch line directional coupler. Measurement of the 10 dB branch line directional coupler shows that the return loss is higher than 30 dB over 10 % bandwidth and the isolation is 35 dB or better over 8 % bandwidth.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.6
• /
• pp.598-604
• /
• 2011

A method of miniaturizing branch line coupler with connected coupled lines is presented. The quarter-wavelength transmission lines in the typical microstrip branch line coupler are replaced with the connected coupled lines with same characteristics of ones for compact size. The connected coupled line is analyzed by T-equivalent circuit and Z parameters based on the even-odd mode analysis. The proposed branch line couplers with connected coupled line are designed and fabricated on FR4 substrate at 2.4 GHz. The measured results show good agreement with theoretical prediction. And the experimental results show that the size of coupler is 37 precent smaller than conventional coupler. This minimized coupler is suitable for Butler Matrix as feeder for mobile communication beam forming antenna.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.11
• /
• pp.960-965
• /
• 2015

In this paper, a coupled line directional coupler using an LUC(Low-pass filter Unit Cell) of artificial transmission line is presented. The conventional coupled line coupler is limited in length by the ${\lambda}/4$ transmission line while the proposed coupling structure is implemented smaller than $90^{\circ}$ by inserting the phase delay line between two coupled line, reduced in physical size by configuring a phase delay line with an LUC having the characteristics of a typical transmission line in a particular frequency. A coupler having -10 dB coupling factor at the center frequency of 700 MHz is designed, fabricated. The measured result agrees well with that of conventional one. The length of the fabricated coupled line coupler has about 45 % in length compared to the conventional one.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.328-332
• /
• 2000

본 논문에서는 기생 패치 구조와 적층 구조의 광대역 마이크로스트립 안테나에 평행 결합 선로 형태의 광대역 임피던스 정합 회로를 결합하여 쉽게 추가적인 임피던스 대역폭 개선을 얻을 수 있음을 제안하였다. 평행 결합 선로 형태의 광대역 임피던스 정합 회로 설계를 위하여 분포 회로 방식의 반복적인 방법을 제시하였고. 설계\ulcorner제작 결과 기생 패치 구조와 적층 구조에서 각각 56.23%와 16.45%의 추가적인 임피던스 대역폭 개선을 이룰 수 있었다. 그리고 방사 패턴과 측정된 이득을 보면 평행 결합 선로의 결합으로 인한 방사 패턴에서의 큰 변화는 보이지 않았고, 이득에서는 평행 결합 선로 부분의 커플링 손실로 인해 최대 이득이 약 1 dB 정도 감소하는 것을 확인할 수 있었다.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.4 no.2 s.7
• /
• pp.67-72
• /
• 2005

This work proposes a novel coupled line coupler structure based on the asymmetric cascaded connection of coupled lines. The proposed structure can be designed in smaller size than conventional single section coupled line couplers. Also, the additional design freedom offered by the proposed structure can serve many useful purposes such as the output phase control or the flexible coupler layout for complex circuit routing environments.

• Proceedings of the KAIS Fall Conference
• /
• 2009.12a
• /
• pp.223-225
• /
• 2009

본 논문에서는 CRLH 전송 선로를 이용한 스터브 구조의 이중 대역 가지선로 결합기를 제안한다. 기존의 스터브 구조의 이중 대역 가지 선로 결합기는 동작하는 두 주파수가 근접할수록 스터브 선로의 임피던스가 증가해 구현이 불가능 하다. 제안된 이중 대역 가지선로 결합기는 비교적 근접한 1800MHz와 2300MHz 두 주파수에서 동작한다. 고 임피던스 스터브 선로는 이중 대역 소자 설계에 유용한 CRLH 전송 선로를 사용하여 구현 된다. 두 주파수에서 측정된 삽입 손실은 이상적인 결합기에 비해 최대 1.88dB의 오차가 났으며 두 출력 포트 사이의 위상차는 $1^{\circ}$미만 이다. 동작하는 두 주파수의 비는 1.28:1로 비교적 작은 차이를 보인다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.9 no.2
• /
• pp.1-16
• /
• 1972

In this paper, the characteristics of linearly tapered strip-line filters, where the even-mode and odd-mode characteristic impedances vary linearly with the same degree along the lines, are analyzed. The Impedance parameters of linearly tapered coupled strip-line, which is made by connecting two linearly tapered unsymmetric coupled strip-lines In cascade and the I:no input and output terminals are made equal, are obtained. Using the above parameters, the Image parameters of linearly tapered coupled strip-line filters are derived. The result of analysis shows that the line length can be made shorter and also the stop-band width between the fundamental and second pass-band becomes wider, compared with the coupled strip-line filters which use uniform strip-lines. Furthermore, the difference of impedance levels in the fundsmental and second pass-band becomes larger with the degree of taper of the lines. This property is unique, in comparison with the case of uniform or exponentially tapered strip-line filters.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.9
• /
• pp.1949-1956
• /
• 1997

The mode parameters of asymmetrical coupled microstrip lines on composite substrates are derived by using closed form expression. A 10 dB directional couplers, where the center frquency is 1.8 GHZ, are fabricated on a single-layer substrate and on compsite substrates respectively. It is shown that coupler on a single-layer substrate.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.2 s.117
• /
• pp.191-198
• /
• 2007

The electromagnetic coupling between transmission lines in PCB design can degrade the performance of equipment operations. The coupling phenomenon is caused by electromagnetic fields generated by the currents on the transmission lines and the risers. In this paper, an improved method of crosstalk analysis for bent coupled lines on a PCB is proposed and investigated. In the previous cascading method combined with circuit-concept approach, bent coupled lines are devided into sections and each section is represented by ABCD matrix and then they are cascaded. In the proposed method, the crosstalk of bent coupled lines is calculated by the modified circuit-concept approach, where the coupled region is not restricted to the region projected by a generator line on a receptor line but is the total length of receptor line in calculating the forcing terms. Finally, the accuracy of the proposed approach is verified by comparing the calculated results with the measured ones for several bent coupled-line examples.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.7
• /
• pp.734-743
• /
• 2010

In this paper, we analyzed the EMP coupling for the nonuniform transmission lines, such as twisted cables, using the chain matrix algorithm and the multi-conductor analysis. The BLT method is widely used for the EMP coupling analysis of the transmission line, however, it is difficult to apply to the nonuniform transmission lines. In order to analyze the EMP coupling of nonuniform transmission lines, the whole nonuniform transmission line is divided into incremental uniform line sections of the finite numbers, and the coupling in each small sections is now summed up to get the EMP coupling effect of the entire nonuniform transmission line. To verify the proposed EMP coupling analysis method, the result of the EMP coupling simulation is compared with the solution of BLT equations for a uniform transmission line case. The proposed method is applied to the twisted cable over ground in case of being illuminated by the HEMP in order to analyze the EMP coupling.