• Composites Research
• /
• v.12 no.3
• /
• pp.8-16
• /
• 1999

Carbon woven fabric/C/SiC composites were fabricated by multiple impregnations of carbon woven fabric/carbon preform with the polymer precursor of SiC, i.e., polycarbosilane. In addition, two kinds of low density carbon/carbon preforms which had different fiber volume fraction and fiber orientation, i.e., a carbon woven fabric(${\thickapprox}$55 vol%)/carbon and a chopped carbon fiber${\thickapprox}$40 vol%)/carbon composites, were reaction-bonded with a silicon melt at 1$700^{\circ}C$ in a vacuum to fabricate dense carbon fiber/Si/SiC composites. The reaction-bonding process increased the density to ~2.1 g/$cm^3$ from 1.6 g/$cm^3$ and 1.15 g/$cm^3$ of a carbon woven and a chopped carbon preforms, respectively. All of the composites fractured with extensive fiber pull-out. The higher the density the higher the stiffness and proportional limit stress. The mechanical properties obtained from a three-point bend and tension tests were compared. The ratios of the peak tensile stresses to the bending strengths of a carbon woven and a chopped carbon composites were about one-third, respectively. The carbon woven fabric/Si/SiC composites with density of 2.06 g/$cm^3$ showed ~120 MPa of ultimate strength and ~80 MPa of proportional limit in bend testing.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.44 no.2
• /
• pp.200-209
• /
• 2017

The aim of this study was to evaluate the shear bond strength (SBS) of three typical restorative materials - glass ionomer cement (GIC), resin-modified glass ionomer (RMGIC) and composite resin (CR) - to different pulp capping materials, i.e., Theracal $LC^{TM}$ (TLC), $Biodentine^{TM}$ (BD), and $ProRoot^{TM}$ white MTA (WMTA). 90 acrylic blocks with a center hole were prepared. The holes were completely filled with three pulp capping materials (TLC, BD, and WMTA), with 30 specimens per capping material. The samples were then randomly divided into 3 subgroups of 10 specimens each and were overlaid with GIC, RMGIC, or CR. A total 9 specimen groups were prepared. The SBS was assessed using a universal testing machine. Kruskal-Wallis test and Mann-Whitney's test were performed to compare the SBS among the subgroups (p < 0.05). After the SBS test, the fractured surfaces were examined under a stereomicroscope at a magnification of $25{\times}$. The highest and lowest SBS values were recorded for TLC-CR and TLC-GIC, respectively. With regard to the SBS to the three pulp capping materials, CR was found to be superior to RMGIC and GIC. BD showed a higher SBS compared to TLC and WMTA when used with GIC.

• Korean Journal of Microbiology
• /
• v.51 no.2
• /
• pp.115-125
• /
• 2015

A monoclonal antibody AP64 IgM binds to human acute nonlymphocytic leukemia (ANLL) cell line HL60 and also cross-reacts with the homologous antigen in a rat ANLL cell. This antibody mediated by complement, has leukemia a suppression effect. In this study, we generated a recombinant single-chain variable domain fragment (ScFv) which were derived from $V_H$ and $V_L$ cDNA of AP64 IgM-secreting hybridoma by RT-PCR. The two variable regions were joined with a single 15 amino acid linker $(G_4S)_3$. This recombinant ScFv was expressed as a single polypeptide chain from Escherichia coli BMH 71-18. The recombinant ScFv was purified by applying the periplasmic extract to $Ni^+$-NTA-agarose affinity column and detected with westernblot. The purified recombinant ScFv recognized a surface antigen (about 30 kDa) of HL60 cell line which is the same antigen detected by parental AP64 IgM. But the affinity of ScFv for a surface antigen of HL60 was lower than that of the parental AP64 IgM, which needs to be further improved. Overall, the recombinant ScFv specific to HL60 might be a useful bioreagent for either diagnostic or therapeutic purposes.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.04a
• /
• pp.30-30
• /
• 1999

샌드위치 복합재는 단일 부재의 금속재나 복합재에 비해 높은 비강성과 비강도를 얻을 수 있을 뿐 아니라 면재와 코아를 적절하게 조합하면 우수한 피로특성, 단열성, 흡음성 등을 얻을 수 있기 때문에 항공기, 철도차량, 선박, 냉동컨테이너, 건축재 등에 널리 활용되고 있다. 대부분의 샌드위치 복합재는 면재와 코아를 일차 또는 이차 선착을 통해 제작하기 때문에 운용 중 샌드위치 복합재에 가해질 수 있는 충격하중 등으로 인해 면재와 코아 사이의 층간분리, 면재의 인장파괴, 코아의 압축파괴, 코아의 진단파괴 등과 같은 손상이 생길 우려가 있다. 최근에는 샌드위치 복합재가 갖는 이러한 문제점들을 해결하기 위한 방편으로 코아의 양면에 부착된 면재들을 코아의 두께방향으로 스티칭함으로써 서로 일체형으로 결합시킨 형태인 스티칭된 샌드위치 복합재의 개발이 시도되고 있다.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.5
• /
• pp.1216-1224
• /
• 1998

In the object oriented methods, most of the objects are independent from the another. However to get their job done from the system's point of view, they must have some kind of connection established among them. This means that the cooperation among the objects through the interaction is just as important as the static side of the objects. Usually, checking for correctness, compatibility and reasoning of the objects is limited due to the fact that the interactions between the objects are expressed in the form of a line or a box. The reuse experts often claim that the design reuse is more important than code reuse, mostly because it can be applied in more contexts and so is more common. The composition of the objects is also considered as a very important definition in the area of framework which is generally known as a technique to support reuse at both the coding and the designing level. Therefore on this thesis, the composition of such objects has been studied to provide a formal means of evaluating the component's compatibility and better possibility for further improvement in the area of framework, by formalizing the component compositions using the LOTOS.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.8A
• /
• pp.610-617
• /
• 2009

This paper proposes a cross-layer design combining adaptive modulation and coding (AMC) with truncated hybrid automatic repeat request (HARQ) for wireless multicast transmission, in order to increase the spectral efficiency while meeting the target quality-of-service (QoS). In the design, we provide the selection criterion of AMC so as to satisfy the target packet error rate (PER) of all users when the multicast data is received through the common channel and the number of retransmission is limited by the delay constraint of the service. The analytically derived results show that the cross-layer design using HARQ provides a better spectral efficiency than the AMC without HARQ by allowing retransmission and code combining. It is also observed that the design for multicast outperforms that for unicast in the mid to high signal-to-noise ratio region.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.275-276
• /
• 2010

In this study, using experimental results on the autogenous expansion of concrete containing MgO, autogenous expansion model which considers water-binder ratio, amount of MgO and curing temperature was suggested. The results predicted by autogenous expansion model agreed well with experiment results.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.2
• /
• pp.90-96
• /
• 2009

The high rising building construction makes increasing the requirement of high strength concrete. Especially, the workability analysis is related with dispersion of admixture such as SF for improving strength and FA, BS for reducing construction cost and improving durability of Ultra High Strength Concrete which has over 100 MPa of compressive strength is very important. Precisely, decreases dispersion because of lumping situation of each admixture and it causes the workability of admixture is decreased. Therefore, the workability of cement paste is tested for analyze effects of pre-mixed cement for solving those problems with it to this research. The summary of the results are like below. First of all, OBS is increasing workability more than OFS. This result causes that the glassy surface of BS in the OBS is increasing workability and the absorption of admixture of FA in the OFS is decreasing workability. In the case of mixing methods, pre-mixing method is increasing workability more than normal one. This result shows that the normal mixing method is bad dispersion of binders. The other side, the pre-mixing method is good. Furthermore, depending on the mixing time, according to the increasing mixing time such as 30, 60, and 120 seconds, the dispersion of binders and workability turns better.

• Applied Chemistry for Engineering
• /
• v.26 no.1
• /
• pp.104-110
• /
• 2015

It is known that polymer concretes are 8~10 times more expensive than ordinary Portland cement concretes; therefore, in the production of polymer concrete products, it is very important to reduce the amount of polymer binders used because this occupies the most of the production cost of polymer concretes. In order to develop a technology for the reduction of polymer binders, smooth and spherical aggregates were prepared by the atomizing technology using the oxidation process steel slag (electric arc furnace slag, EAFS) and the reduction process steel slag (ladle furnace slag, LFS) generated by steel industries. A reduction in the amount of polymer binders used was expected because of an improvement in the workability of polymer concretes as a result of the ball-bearing effect and maximum filling effect in case the polymer concrete was prepared using the smooth and spherical atomized steel slag instead of the calcium carbonate (filler) and river sand (fine aggregate) that were generally used in polymer concretes. To investigate physical properties of the polymer concrete, specimens of the polymer concrete were prepared with various proportions of polymer binder and replacement ratios of the atomized reduction process steel slag. The results showed that the compressive strengths of the specimens increased gradually along with the higher replacement ratios of the atomized steel slag, but the flexural strength showed a different maximum strength depending on the addition ratio of polymer binders. In the hot water resistance test, the compressive strength, flexural strength, bulk density, and average pore diameter decreased; but the total pore volume and porosity increased. It was found that the polymer concrete developed in this study was able to have a 19% reduction in the amount of polymer binders compared with that of the conventional product because of the remarkable improvement in the workability of polymer concretes using the spherical atomized oxidation steel slag and atomized reduction steel slag instead of the calcium carbonate and river sand.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.1
• /
• pp.37-44
• /
• 2017

Red mud is an inorganic by-product produced from the mineral processing of alumina from Bauxite ores. The development of alkali-activated slag-red mud cement can be a representative study aimed at recycling the strong alkali of the red mud as a construction material. This study is to investigate the optimum water content, compressive strength, water absorption and efflorescence of alkali-activated slag-red mud soil pavement according to binder type. The results showed that the optimum water content, moisture absorption coefficient and efflorescence area of alkali-activated slag-red mud soil pavement increased but the compressive strength of that decreased as the redmud content increased.