• Journal of the KSME
• /
• v.22 no.3
• /
• pp.203-213
• /
• 1982

이재결합재의 피로시험에서 나타나는 피로균열성정거동은, 역시 균열선단이 결합경계의 근방에 있거나 경계상에 있을 때의 것이 균질재료에서의, 거동과 비교.검토되어야겠다. 이재결합재를 여기에서는 탄성계수 E 값이 동일(또는 근접)한 이재간의 결합재와, E 값이 현저히 다른 이재 간의 결합재로 나누어 그 피로시험예를 검토해 나가기로 하겠다. 또한 전술한 바와 같이 이재 결합재에 의한 피로시험 그 자체의 난전으로 말미암아 파괴역학적으로 해석된 이재결합재피로 균열거동연구보고가 극히 부진함에 비추어 여기에서는 주로 필자가 발효한 연구보고들을 바탕 으로 해서 검토해 나가기로 하겠다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.749-752
• /
• 2008

This experimental study compared polymer cement mortar with inorganic polymer binder mortar for physical properties by Si/Al mol ratio change of inorganic polymer binder. As the result of this experiment, We found that when Si/Al mol ratio goes up flexural strength and compressive strength increases but workability becomes worse. And according to the keeping them for 28 days we found that physcal property becomes worse when Si/Al mol ratio is larger than 2.61. When Si/Al mol ratio of inorganic polymer binder is from 2.43 to 2.61 compressive strength increases than over 32% after keeping for 7 days and over12 % for 28 days

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.4
• /
• pp.433-442
• /
• 2021

In this study, the properties of no-fines polymer concrete with different polymer binder contents were evaluated. The polymer concrete was formulated using a polymeric binder (unsaturated polyester resin), fly ash, and recycled coarse aggregate (60%) and crushed coarse aggregate (40%). The polymeric binder content (4.0-6.0wt.%) was used as an experimental variable because it dramatically affects both the cost-effectiveness and material properties. The results showed that the density, compressive strength, flexural strength both before and after exposure to freezing and thawing increased as the polymer binder content increased, while the absorption, void ratio, permeable voids, coefficient of permeability, and acid resistance (mass loss by acid attack) decreased as the polymeric binder content increased. In particular, even though the void ratio was 18.4% and the water permeability coefficient was 7.3mm/sec, the compressive strength and flexural strength were as high as 38.0MPa and 10.0MPa, respectively, much more significant than those of previous studies. Other properties such as absorption and acid resistance were also found to be excellent. The results appear to be rooted in the increased adhesion of the binder by adding a cross-linking agent and the surface hydrophobicity of the polymer.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.1
• /
• pp.64-71
• /
• 2015

Silica fume is generally adopted as admixture for Ultra High Strength Concrete (UHSC) owing to its remarkable contribution to the strength and durability but increases significantly the fabrication cost of UHSC. Accordingly, this study investigates the replacement of silica fume by blast furnace slag (BS) and fly ash (FA) in order to lower the fabrication cost of 80MPa-UHSC. To that goal, experiment is conducted on the mix proportions of mortar in terms of its binder combination, water-to-binder ratio (W/B) and unit binder content. Based on the experimental data, a mix design of concrete is derived and its properties are verified. The results reveal that a W/B of 21% and unit binder content of $720kg/m^3$ are appropriate to achieve 80MPa-UHSC using a binder composed of 60% of OPC, 30% of BS and 10% of FA. The properties of the corresponding UHSC are seen to be satisfactory with a slump flow of 715mm and compressive strength of 97MPa at 28days. The application of the binder combination derived in this study is analyzed to reduce the cost by 50% of binder compared to the mix using silica fume while realizing equivalent performance.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.12 no.4
• /
• pp.95-104
• /
• 2004

A styrene solution of waste expanded polystyrene with a crosslinking agent and an initiator was used as a binder for waste wood-plastic composite panels. The waste wood-plastic composite panels are prepared with various binder contents and filler-binder ratios by using a hot press molding method. The apparent density of the composite panels is increased with increasing binder content and filler-binder ratio, while their water absorption and expansion in thickness are decreased with increasing binder content and filler-binder ratio. The maximum flexural strength and wet flexural strength of the composite panels are obtained at a binder content of 35% and a filler-binder ratio of 0.8. Decreases in the flexural strengths of the composite panels due to water immersion at 20 and $100^{\circ}C$ are hardly recognized at binder contents of 30% or more.

• Journal of the Korea Institute of Building Construction
• /
• v.16 no.1
• /
• pp.45-52
• /
• 2016

In this research, characteristic properties of gel time and homo gel strength of liquid chemical grouting material for soil grouting using non-cement binder(NCB) were measured according to kinds of liquid B's Binders, W/B of liquid B's Binders and the volume ratio between liquid A and liquid B in order to examine on the applicability of soil grouting material using non-cement binder. The test was performed using NCB-1, NCB-2, NCB-3 which are environment-friendly inorganic binders developed by means of collaboration by our research team and which are different from chemical composition ratio each other. In conclusion, it was found that NCB could be applied to liquid soil grouting material using non-cement binder and replace ordinary portland cement, because NCB had the most excellent performance in certain section of gel time and homo gel strength in condition of this experiment.

• Journal of the Korea Concrete Institute
• /
• v.25 no.6
• /
• pp.657-665
• /
• 2013

The purpose of this study is the basic research of self-compacting concrete using Alkali-Activated Slag (AAS) binder in order to emphasize the durability of structures and facilitate casting the fresh concrete in field. The AAS binder emitted low carbon dioxide ($CO_2$) is eco friendly material of new concept because AAS products not only emit little $CO_2$ during production but also reuse the industrial by-products such as ground granulated blast-furnace slag (GGBS) of the steel mill. Until now, almost of domestic and foreign research are using Ordinary Portland Cement (OPC) for self-compacting concrete, and also, nonexistent research about AAS. The self-compacting concrete must get the performance of flowability, segregation resistance, filling and passing ability. Nine concrete mixes were prepared with the main parameter of unit amount of binder (400, 500, 600 $kg/m^3$) and 3 types of water-binder (W/B) ratio. The results of test were that fresh concretes were satisfied with flowability, segregation resistance, and filling ability of JSCE. But the passing ability was not meet the criteria of EFNARC because of higher viscosity of AAS paste than OPC. This high viscosity of AAS paste enables the manufacturing of self compacting concrete, segregation of which does not occur without the using of viscosity agent. It is necessary that the development of high fluidity AAS binders of higher strength and the study of better passing ability of AAS concrete mixes in order to use self compacting AAS concrete in field.

• Journal of the Korea Concrete Institute
• /
• v.24 no.5
• /
• pp.597-604
• /
• 2012

The present study assessed the $CO_2$ emissions of concrete according to the type and replacement ratio of supplementary cementitious materials (SCM) and concrete compressive strength using a comprehensive database including 2464 cement concrete specimens and 776 cement concrete mixes with different SCMs. The system studied in $CO_2$ assessment of concrete based on Korean lifecycle inventory was from cradle to pre-construction, which includes consistent materials, transportation and production phases. As the performance efficiency indicators, binder and $CO_2$ intensities were analyzed, and simple equations to evaluate the amount of $CO_2$ emission of concrete were then formulated as a function of concrete compressive strength and the replacement ratio of each SCM. Hence, the proposed equations are expected to be practical and useful as a guideline to determine the type and replacement ratio of SCM and unit content of binder in concrete mix design that can satisfy the target compressive strength and $CO_2$ reduction percentage relative to cement concrete.

• Journal of the Korea Concrete Institute
• /
• v.23 no.2
• /
• pp.145-150
• /
• 2011

Presently, mass concrete structures are being built in federal and private projects of civil infrastructures and building structures. The hydration heat of mass concrete structures is the most important factor in the quality of concrete matrix and construction period. Moreover, internal cracks caused by hydration heat degrades durability, water tightness, and strength of concrete. To reduce hydration heat, it is necessary to blend belite cement (${\beta}-C_2S$) with industrial by-products (i.e. granulated slag and fly ash). In this experiment, 14 levels of binary binders and 4 levels of ternary binders were used to understand the effect of different replacement ratio on hydration heat, strength and microstructure (i.e. SEM and XRD) of mortar. Cumulative hydration heat at 28 days for the binary and ternary binders was affected by replacement ratio of fly ash and/or granulated slag. As fly ash content increased, hydration heat decreased. As granulated slag content increased, reduction rate of the hydration heat was lower than when fly ash was used. Especially, the hydration heat of ternary binder blended with 40% flyash and 30% granulated slag showed about 50% of hydration heat from using belite cement (P). The study results showed that the temperature rise of concrete matrix can be decreased by using blended belite binders producing low hydration heat and reasonable strength.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.05a
• /
• pp.324-325
• /
• 2012

다이아몬드 마이크로 블레이드의 절삭 효율을 향상시키고 소결 공정 중 윤활제의 유동성과 젖음성이 다이아몬드 마이크로 블레이드의 물성에 미치는 영향을 연구하기 위해 Cu/Sn 금속 결합재에 표면을 부식시킨 $WS_2$와 부식을 시키지 않은 $WS_2$ 윤활제를 각각 동일한 체적 분율로 첨가하였다. 윤활제의 표면 개질에 따른 마이크로 블레이드 결합재의 내마모성과 굽힘 강도 시험을 행하였고, 실착 절삭 시험을 위한 마이크로 블레이드 시편을 제작하여 수명 및 효율을 평가하였다. Cu/Sn 금속 결합재 파면에서의 $WS_2$ 입자 방향 분석을 통해 표면 개질 과정을 거친 $WS_2$가 압축소결 공정 중 압축 방향에 수직하게 위치하려는 경향이 크게 나타났으며, 이는 소결체의 강도와 경도를 향상시켰다. 마이크로 블레이드의 절삭 효율 및 수명을 평가하기 위한 실착 절삭 시험 결과, 윤활제 표면 부식처리는 처리하지 않은 경우에 비하여 절삭성능은 비슷하게 관찰되었으나 결합재와의 계면 결함을 줄이므로써 블레이드의 수명을 연장시킬 수 있었다.