• The Journal of the Acoustical Society of Korea
• /
• v.31 no.8
• /
• pp.514-522
• /
• 2012

The temperature dependence of the characteristics in a PZT-5 piezoelectric ceramic vibrator with the transverse mode was investigated in the range of $-100^{\circ}C$ to $90^{\circ}C$ using a thermal vacuum chamber to utilize the vibrator in aerospace industries. As the results, at room temperature, the resonant and anti-resonant frequencies had the minimum value, whereas, the dielectric constant increased linearly from about 2500 to 7500 in the given temperature range. The mechanical loss decreased linearly from 0.08 to 0.03. Through the regression analysis, the temperature dependence functions of the characteristics were derived to linear and square regression functions. Applying the functions, the input admittance characteristics of the piezoelectric vibrator were calculated, and the results showed good agreement with measured ones. It can be confirmed that this method is useful to estimate the characteristics change of the piezoelectric vibrator caused by the temperature change under the space environment.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.5
• /
• pp.1-9
• /
• 1989

In binary digital transmission system the band-limiting is required for the better transmission efficiency. But in the case of band-limiting the intersymbol-interference (ISI) usually takes place. In this paper, in an attempt to design band-limiting filter which has minimum ISI and maximum stop-band loss, first, making use of analog filter by combining Binary Transversal Filter (BTF) and analog filter (4th Butterworhfilter), we found the value that minimizes ISI phenomenon by getting step response of rectangular pulse resulting from BTF in time domain. Second, we found filter characteristic we want to in frequency domain for band-limiting and minimized the error. And then we obtained resistor value (Tap coefficient) in order to design algorithm for optimum filter. Also we showed the example of simulation in case we established the resistors with 3,5 and 7 respectively. With 7 resistors set, we identified that the ripple of about minus 30dB was taken place.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.7
• /
• pp.703-714
• /
• 2010

This paper describes the design optimization of a rotating rectangular channel with staggered arrays of pin-fins by Kriging metamodeling technique. Two non-dimensional variables, the ratio of the height to the diameter of the pin-fins and the ratio of the spacing between the pin-fins to the diameter of the pin-fins are chosen as the design variables. The objective function that is a linear combination of heat transfer and friction loss related terms with a weighting factor is selected for the optimization. To construct the Kriging model, objective function values at 20 training points generated by Latin hypercube sampling are evaluated by a three-dimensional Reynolds-averaged Navier-Stokes (RANS) analysis method with the SST turbulence model. The Kriging model predicts the objective function value that agrees well with the value calculated by the RANS analysis at the optimum point. The objective function is reduced by 11% by the optimization of the channel.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.8
• /
• pp.837-843
• /
• 2008

This paper proposes a power divider based on meta-material structure with dual-band operation. The meta-material structures of left-hand characteristic are constituted of series capacitors and shunt inductors, but they have parasitic series inductance and shunt capacitance effects. There is represented the composite right/ left-handed transmission line (CRLH-TL) model. When the power divider is implemented by using the CRLH-TL, the power divider can operate dual band. To verify the power divider with dual band, we are implemented to operate dual-band that is 0.88 GHz and 1.67 GHz. The characteristics of divider have the return loss less than each 21.0 dB and 15.8 dB and the insertion loss better than 3.83 dB and 3.64 dB at each frequency. Also, the output phase difference is $3{\sim}6^{\circ}$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.134.1-134.1
• /
• 2014

콜로이달 리소그래피는 나노미터 크기의 나노구를 자가조립에 의해 정렬시킴으로써, 파장이하 크기의 주기 구조를 저비용으로 쉽게 구현할 수 있는 패터닝 기법이다. 콜로이달 리소그래피나 소프트 리소그래피와 같이 대면적 패터닝이 가능한 공정을 태양전지를 위한 반사방지 및 광 포획 증대 구조에 적용함으로써, 기존 성능을 크게 향상시켰다. 본 연구에서는, 유한차분 시간영역 수치해석법을 이용하여 반사 방지 및 광 포획 증대 구조에 대한 이론적 검증 및 설계를 진행하였고, 콜로이달 리소그래피 및 반도체 공정을 통해 샘플을 제작하였으며, 제작된 샘플의 성능을 적분구를 겸비한 자외선 가시광 근적외선 영역 분광기를 통해 평가하였다. 반사방지 나노섬을 겸비한 나노 원뿔대 언덕형 굴절률 소자를 구현함으로써, 300나노미터 이하의 구조체를 사용하지 않고도 근자외선 영역을 포함하는 태양광 에너지의 손실을 최소화할 수 있는 광대역 방사방지 구조체를 제시하였다. 나노 원뿔대가 격자상수 이상의 파장에 대한 언덕형 굴절률을 제공하고, 4분의 1파장 나노섬 반사방지막이 격자 상수 이하의 근자외선 태양광을 추가적으로 흡수하여, 근자외선 영역에서의 평균 반사율을 3.8% 수준으로 달성 할 수 있었다. 또한, 낮은 양호계수를 갖는 속삭임 회랑 공진기 어레이를 이용하여, 박막 태양전지에 적합한 유전체 기반 광포획 증대 나노구조를 제시하였다. 나노반구, 나노고깔, 나노구, 함몰형 나노구 어레이 형태를 가지며, 500nm의 주기를 갖는 유전체 표면 텍스쳐드 구조를 초박형 비정질 실리콘 필름(100nm) 위에 제작하여 광대역 광 포획 증대 효과를 실험적으로 평가하였다. 구조들 중 함몰형 나노구 어레이가 결합된 비정질 실리콘 박막이 가장 높은 성능을 보였으며, 구조가 없는 경우 대비 약 67.6%의 가중 흡수율 증가를 나타내었다. 특히, 함몰형 나노구 어레이 구조 중 폴리메틸메타아크릴레이트로 제작된 평판형 함몰층은 나노구 비정질 박막 실리콘 사이의 접착력 및 기계적 강성을 향상시켰을 뿐 아니라, 함몰층 내부로 회절되고 산란된 빛들이 도파모드 효과에 의해 부가적인 광 포획 증대를 가져옴으로써, 가장 높은 광 포획 효과를 얻을 수 있었다. 유전체 기반 나노 구조들은 간단하고 저비용이며, 대면적으로 쉽게 제작할 수 있는 자가 조립 기반 콜로이달 리소그래피 및 소프트 리소그래피 기술을 이용하여 제작되었다.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.260-268
• /
• 2020

This paper presents the high frequency resonant inverter of class D SEPP(Single-Ended Push Pull) type using LS-ZVS-LSTC, which can reduce the switching losses during the turn-on and turn-off switching time. The analysis of high frequency resonant inverter using LS-ZVS-LSTC(Low-loss Turn-off Snubber Capacitor) proposed in this paper is described in general by adopting the normalized parameters. The operating characteristics of the proposed high frequency resonant inverter were also evaluated by using the control parameters such as the normalized control frequency(μ), the normalized load time constant(τ), the coupling factor(κ) and so on. Based on the characteristic values through the characteristics of evaluation, an example of the design method of the 1.8[kW] class D SEPP type high frequency inverter is suggested, and the validity of the theoretical analysis is verified using the experimental data.

• Composites Research
• /
• v.32 no.1
• /
• pp.71-77
• /
• 2019

In this study, the structural and rheological characterizations of polyacrylonitrile(PAN)/dimethyl sulfoxide(DMSO) solutions for PAN fiber were investigated according to the change of storage times and temperatures. As a result, PAN/DMSO solutions exhibited a very characteristic rheological behavior with variation of temperature. The solutions showed an increase of complex viscosity and a decrease of loss tangent($tan{\delta}$) as temperature was increased over the temperature range of 40 and $70^{\circ}C$ and it could be seen that the viscosity rapidly increased at low frequency. These results indicated that the gel polymer and denser gel structure were formed due to the intermolecular hydrogen bonding of water in the polymer solution depending on the storage time.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.11
• /
• pp.9-18
• /
• 2003

Two configurations of Film Bulk Acoustic Wave Resonators with acoustic quater-wave bragg reflector layers are theoretically analyzed using equivalent circuits and the difference of their characteristics are discussed. We compare the characteristics of λ/2 mode to those of ideal FBAR with top and bottom electrode contacting air and the characteristics of λ/4 mode to those of ideal FBAR with top electrode contacting air and bottom electrode clamped. We assume that the piezoelectric film is ZnO, the electrode is A1 and the substrate is Si, ABCD parameters are extracted and input impedance is calculated by converting the equivalent circuit from Mason equivalent circuits to the simplified equivalent circuits that ABCD parameters are extracted possible, From the variation of resonance frequency due to the change of thickness of reflector layers and the variation of electrical Q due to the change of mechanical Q of reflector layers, it is confirmed that the reflector layer just under the bottom electrode have the greatest effect on the varation of resonance frequency and electrical Q. It is shown that the number of reflector layers required for the saturation of electrical Q decreases with the increase of the impedance ratio of reflector layers and electrical Q of λ/2 mode is larger than that of λ/4 mode, Electromechanical coupling factor is independent of the number of layers, The impedance ratio of reflector layers becomes larger as the electromechanical coupling factor becomes larger, The electromechanical coupling factor of the two mode are smaller than those of ideal FBARs because of the trapping of acoustic energy in the reflector layers, The insertion loss of the ladder filter decreases with the increase of the number of reflector layers but the bandwidth is not affected much by the number of reflector layers, As the impedance ratio of reflector layers becomes larger the insertion loss becomes smaller and the bandwidth becomes wider, In our analysis of the two mode, characteristics of λ/2 mode appear to be slightly more favorable than that of λ/4 mode

• Applied Chemistry for Engineering
• /
• v.18 no.1
• /
• pp.77-83
• /
• 2007

It is essential that second order nonlinear optical materials have low optical propagation losses in the wavelengths of second harmonic generation for practical applications in waveguides. Three dipolar chromophores substituted with nitro, cyano, and alkyl sulfone as an electron withdrawing group were prepared. The UV-Vis absorption spectra of the cyano and alkylsulfone chromophores showed a blue-shift compared to the nitro chromophore. The introduction of oxadiazole segment in the chromophore structure led to similar spectral shift. The blue-shift can produce low optical loses at second harmonics. The chromophores were successfully attached to a polyimide, yielding side chain polymers. The nonlinear optical property of the prepared optical polymers was determined by measuring electro-optic coefficient at 1.55 mm. The polymers exhibited high glass transition temperature of over $185^{\circ}C$ and thermal stability to $300^{\circ}C$ through differential scanning calorimeter analysis and thermal gravimetric analysis.

• Composites Research
• /
• v.18 no.4
• /
• pp.27-34
• /
• 2005

Salt water spray and immersion tests were experimentally conducted for over 6 months to investigate the durability of glass fabric/phenolic composites under salt water environment. Mechanical properties such as tensile properties, flexural properties, and shear properties were evaluated and thermal analysis properties such as storage shear modulus, loss shear moduls, and tan 6 were obtained through a DMA. A change in chemical structures was analyzed through a FTIR. According to the results, mechanical properties and thermal analysis properties were sensitive to salt water environment and these properties began to degrade in increasing in exposure times. However, tensile and flexural moduli started to decrease and then slightly increase as increasing in exposure times due to plasticization and crosslinking in matrix as well as physical swelling in composites. Beyond a certain exposure times, these properties began to decrease as further increasing in exposure times. Also the shape and location of peaks in FTIR curves were insensitive to exposure times, but the intensity of peaks would be. finally we found that the durability of glass fabric/phenolic composites were affected on salt water immersion environment rather than salt water spray environment.