• Korean Journal of Plant Resources
• /
• v.10 no.1
• /
• pp.24-29
• /
• 1997

This study was conducted to evaluate the effect of locations and nursing days on the cstablishment and the first-year growth of Aster scaber seedlings in mountainous areas. Survival rates of the seedlings ranged from 72% in Bukbang to 27% in Mt. Yeonyup B. Survival rate of 90 days-seedlings was 65%. 150days-and 120days- seedling had 2 or 3 leaves but it was almost same as that of native plants. The plants grown in Mt. Yeonyup A averaged 10.7cm high and 90 days-seedlings grew best. Dry weight of plants grown from 120 days- and 90days- seedlings was respectively 215mg and 205mg.

• International Journal of Highway Engineering
• /
• v.14 no.3
• /
• pp.41-48
• /
• 2012

In this study the negative skin friction test of foundation pile was performed in order to monitor the negative skin frictional force acting on the steel pipe pile installed in soft soil. The monitored frictional stresses obtained from the long-term loading test. Through the long-term frictional stress monitoring test, the economical period for the construction of the superstructure was determined. The following conclusion were derived from this study: (1) In soft soil, negative skin friction increases with the increase in the rate of settlement. (2) In the friction relationship graph, the period where there is no frictional strain increase is verified and the time for the construction of the superstructure is determined. (3) The pile loading test was performed and the negative skin friction was compared with the test results. It was determined that the negative skin friction after driving was larger than the negative skin friction obtained from the loading test. 15 days after the construction, the monitored value was similar with the theoretical data. (4) It was determined that even during the occurrence of negative skin friction an economical construction management can be performed using the long-term monitoring method of negative skin friction.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.3
• /
• pp.41-50
• /
• 2007

The results from normally consolidated isotropic drained and undrained triaxial compression tests (NCIU and NCID) on sand with high silt content were presented in this paper. The experiments were performed on specimens of Nak-dong River sand with 63% silt content under effective confined pressures, 100 kPa to 400 kPa. From test results, Sandy silt became initially compressive but eventually appeared to provide dilatancy response throughout the entire stress-strain curve The behavior of sandy silt was more difficult to characterize than that of clay and sand due to lower plastic characteristic. Especially, the samples exhibited dilatancy development during shear after failure. The shear behavior and shear strength parameters of sandy silt can be determined as stress-strain behaviors are described by the Mohr-Coulomb failure criterion. The shear behaviors were observed increasing dilatancy volume change tendency with strain-softening tendency after failure. In this paper, the behavior of dilatancy depends on not only sand content but also fine content with low-cohesion during shear in the samples of sandy silt.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.12 no.2
• /
• pp.117-127
• /
• 2010

Gound excavation is frequently executed in unsaturated soil conditions. In this paper, the effect of apparent cohesion in unsaturated soils on the ground behavior during underground excavation is studied. The VPPE (Volumetric Pressure Plate Extractor) test, the unsaturated triaxial test and the trap-door test were carried out to figure out how the behavior of soils varies depending on the variation of apparent cohesion. The test results show that the ground behavior is almost identical if the soil is either fully dry or fully saturated. However, if the soil is partially-saturated with the increase of water content, the ground behaves quite differently. In summary, the apparent cohesion in unsaturated soils plays key roles when excavating underground structures.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.39 no.12
• /
• pp.1839-1845
• /
• 2010

This study was conducted to evaluate the effects of salt soluble protein extracts from anchovy (ASSPE) on sausage during storage at $10^{\circ}C$. Sausages were produced containing 5 and 10% ASSPE. Sausages containing ASSPE showed no significant differences in emulsion stability, color, pH, moisture, viable cell count, and VBN compared to the control. The hardness significantly increased with the addition of ASSPE, and sausages containing 5% ASSPE were the highest in gumminess. In the sensory evaluation, sausages containing 5% ASSPE had the highest score in appearance and springiness. In conclusion, the addition of ASSPE in sausage had no effects on storage characteristics, but had a good effect on improvement of quality and sensory characteristics. Especially, 5% ASSPE sausage had good texture and high sensory characteristics due to increased binding capacity. These results suggest that 5% ASSPE may improve the quality and sensory characteristics of sausage.

• Journal of the Korean GEO-environmental Society
• /
• v.16 no.1
• /
• pp.45-53
• /
• 2015

This study has obtained Soil Water Retention Curve (SWRC) of the unsaturated soil from the volumetric pressure plate extractor test and the triaxial compression tests was also conducted. By using the rainfall data measured in the site the seepage analysis of unsteady flow was performed with the program of SEEP/W in Geostudio 2007 and stability of the slope was analyzed with SLOPE/W program. Results of analyses show that shear strength of the unsaturated soil increases with the increase of matric suction. And it was also found that the net volumetric stress and the apparent cohesion increased with the matric suction. The seepage analysis of rainfall represents that the increasing rate of negative pore pressure at the zone of large negative pore pressure is appeared to be high even though lower rainfall intensity, but this tendency declines with ground depth. The stability analysis of slope was carried out for the actual plane of failure with the data representing the field condition. The factor of safety thus calculated was about unity (1.0) or just below, which means that the adopted method of analysis is in good agreement with the field condition.

• The Journal of Korean Academy of Prosthodontics
• /
• v.48 no.4
• /
• pp.308-314
• /
• 2010

Purpose: The purpose of this study is to analyze the change in re-osseointegration over time and bone reaction at the interface between implant fixture and the surface of the bone, after destroying re-osseointegration by distorting the bone-implant interface artificially. Materials and methods: Experimental implant fixtures (cp titanium, ${\phi}3.75\;mm{\times}4\;mm$) which didn't have surface treatment were produced. Two or three fixtures were implanted on both tibias of twelve female rabbits (New Zealand white, more than 3.5 kg). Then after six weeks, removal torque (RT) was measured and the results were recorded as the first measurement values. The fixtures were submerged again to get reosseointegration between the bone and fixture. To identify the change in re-osseointegration of submerged fixtures over time, six groups had the healing time for four days (group I), one week (group II), two weeks (group III), three weeks (group IV), four weeks (group V) and five weeks (group VI), and then the secondary removal torque was measured for each group. To identify the bone formation under fluorescent light, tetracycline (15 mg/kg, IM) were treated on the rabbits of each group. After the second measurement, the rabbits were sacrificed, and 16 slides were made, two or three for each group. The slides were observed under the fluorescent light with light microscope. To find out the change in the secondary removal torque over the primary removal torque in progress of time, the averages of the increase rate of the primary and secondary torque removal force were calculated. Then, to find out if there were any critical differences between the primary removal torque and the secondary removal torque in each group and among the groups, the results were analyzed statistically by paired t- test, one-way ANOVA, and Duncan's Multiple Range Test. Results: In group I and II, secondary removal torque decreased, especially in group I. In group III, IV, V, and VI, secondary removal torque increased critically. Comparing the differences among the groups, the critical difference was shown between group I, II and group III, IV, V, VI. Mineralization at the interface between the bone and implant fixture was identified from the first week, and bone formation was shown more clearly from the second week. Conclusion: If the implant fixture remains unforced for a certain period of time after the fixture has had iatrogenic mobility, re-osseointegration occurs at the surface of the fixture, and for tibias of rabbits, higher re-osseointegration was obtained within two weeks.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.37-45
• /
• 2018

An electric vehicle is an environmentally friendly vehicle because there is no exhaust gas, unlike gasoline automobiles. On the other hand, because the electric vehicle is driven by electric power charged in batteries, the distance to go through a single charge depends on the energy density of the batteries. Therefore, a lithium-ion battery with a high energy density is a good candidate for batteries in electric vehicles. Because the electrode is an essential component that governs the efficiency of a lithium-ion battery, the electrode manufacturing process plays a vital role in the entire production process of lithium-ion batteries. In particular, the drying process during the electrode manufacturing process is a critical process that has a significant influence on the performance. This paper proposes an innovative process for improving the efficiency and productivity of the drying process in electrode manufacturing and describe the equipment design method and development results. In particular, the design procedure and development method for enhancing the electrode adhesion power, atmospheric pressure superheated steam drying technology, and drying furnace slimming technologies are presented. As a result, high-speed drying technology was developed for battery electrodes through the world's first turbo dryer technology for mass production using open/integrated atmospheric pressure superheated steam. Compared to the conventional drying process, the drying furnace improved the productivity (Dry Lead Time $0.7min{\rightarrow}0.5min$).

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.28 no.3
• /
• pp.328-333
• /
• 1983

Due to fast industrialization and reduced agricultural population, there has been increased farm mechanization to reduce the labor requirement. In rice production, mechanical transplanting has been increasingly popular due to the heavy labor requirement in hand transplanting and development of convenient transplanters. For mechanical transplanting, rice seedlings is grown in boxes with limited soils under super dense population, thus short period of exposure to unfavorable temperature and poor water management would cause severe damage to rice seedlings such as seedling damping off and the similar physiological disorders. Several chemicals were evaluated for their effectiveness to control the disease and disorders, and other effects as plant growth stimulants. 3-hydroxy-5-methylisoxazole-a soil fungicide, Metalozyl-a fungicide which controls mildew, SF 8002-the composite of above two chemicals, and Isoprothiolane-a fungicide which controls rice blast were found to be effective controling seedling damping off and similar physiological disorders, and improvement of physiological characteristics of the seedlings such as the amount of bleeding sap, rooting ability, negative geotrophism, and regrowth after cutting. The results indicated that the chemicals will be very effective raising healthy seedlings even under unfavorable environments by the improvement of physiological activities of seedlings and preventing seedling damping off and the similar physiological disorders.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.527-533
• /
• 2017

As the clothing industry has advanced, dyeing technologies using various dyes have been developed. In recent years, interest in natural pigments has been increasing because of the negative impact of synthetic pigment on human health; therefore, development and application of microbial pigments is demanded. In this study, the dyeing effects on multifiber fabrics and biological activity were assessed using violet natural pigment from the marine bacterium, Microbulbifer sp. PPB12. The violet pigment produced by cultivation of Microbulbifer sp. PPB12 using Marine broth 2216 for 3 days was extracted using ethanol. Once dissolved in 20% ethanol, the violet pigment could be used to dye bleached cotton, diacetate, and especially polyamide. The optimal temperature, time, pH, and bath ratio under the dyeing conditions were $80^{\circ}C-90^{\circ}C$, more than 1 hour, pH 4-6, and 1:25, respectively. The mordant treatment was more suitable for color expression when $Na_2SO_4$ was used after 10 minutes of dyeing, but no significant difference was observed from untreated samples. The violet pigment also showed antibacterial activity against B. subtilis. The results of the present study indicate that the marine bacterial pigment could be an alternative for textile dyeing as a natural dye with antibacterial activity.