• Polymer(Korea)
• /
• v.35 no.2
• /
• pp.130-135
• /
• 2011

Along with the fast development of electronics, the demands of portable electronics and wireless sensors are growing rapidly. The need for self-powering materials capable of powering the electrical devices attached to them is increasing, The piezoelectric effect of polyvinylidene fluoride (PVDF) can be used for this purpose. PVDF has a special crystal structure consisting of a ${\beta}$-phase that can produce piezoelectricity. In this paper, multilayer PVDF films were fabricated to increase the ${\beta}$-phase content. A solution of 10% concentration N;N-dimethylacetamide (DMAc) in PVDF (PVDF/DMAc) was used to fabricate the films via spin coating technique with the following optimum process parameters: a spin rate of 850 rpm, spin time of 60 s, drying temperature of $60^{\circ}C$, and drying time of 30 min, Compared with single-layer PVDF films, the multilayer films exhibited higher ${\beta}$-phase content. The ${\beta}$-phase content of the films increased gradually with increasing number of layers until 4, Maximum ratio of ${\beta}$-phase content was 7.72.

• Composites Research
• /
• v.24 no.6
• /
• pp.7-11
• /
• 2011

Polyurethane oligomers (PUOs) such as UA8297, UP127 and EB8200 were utilized to enhance the anti-bullet property of Dyneema$^{(R)}$/vinylester composites. First, prepregs of PUO and vinylester (XSR10) were prepared via spray coating on Dyneema$^{(R)}$ fabric at 21 % resin content (by volume). In addition, spray coating and film lamination were also carried out with a mixture of XSR10/PUO for selected PUOs. Next, the prepregs were dried at RT for 1-2 h and then at $100^{\circ}C$ for 30 min to remove the solvent and to provide partial cure when necessary. The prepregs were stacked in 24 layers and cured at $120^{\circ}C$ for 5 min under the contact pressure and for additional 25 min at 150 $kg/cm^2$. Finally, the anti-bullet properties of composite samples were evaluated by measuring $V_{50}$ with simulated fragment projectile (SFP, 17 gr). The results showed a 6.5 and 9.0 % increase of $V_{50}$ with UP127 and EB8200, respectively.

• Journal of Korean Society of Forest Science
• /
• v.89 no.3
• /
• pp.378-383
• /
• 2000

Pinus sylvestris plantations in the Eifel mountains, Germany, were studied and classified phytosociologically. Ecological characteristics(soil, natural regeneration & succession) of the plant communities classified were analyzed and described with emphasis on the forest management. According to soil and topographic characteristics, this plantations were divided into four categories ; Vaccinium myrtillus-Pinus sylvestris community of the adequate moisture area, Pteridium aquilium-Pinus sylvestris community of the moisture area, Molinia caerulea-Pinus sylvestris community of the hardened soil layer B and Festuca tenuifolia-Pinus sylvestris of the dry area. Tree species growing below the shrub layer was analyzed. The results were considered as Vaccinium mytillus-Pinus sylvestris, Pteridium aquline-Pinus sylvestris and Molinia caerulea-Pinus sylvestris will be changed into Fagus sylvatica forest following Quercus forest, and Festuca tenuifilia-Pinus sylvestris will be changed into Pinus sylvestris-dominated climax forest.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.739-744
• /
• 2011

Activated carbon SCR(CSCR) catalyst that is used to remove $NO_x$ in exhaust gas including boron discharged from the production process of liquid crystal display(LCD) shows deactivation when boron is deposited to block the pores within the catalyst or to cover its active sites. The spent carbon catalyst is regenerated by washing with various surfactants, drying and calcination. For comparison of the physical and chemical properties before and after the regeneration with the variables, type of surfactants and calcination condition, element analysis by ICP, $N_{2}$ adsorption were conducted. $DeNO_{x}$ in SCR with $NH_3$ was carried out in a fixed bed reactor at $120^{\circ}C$. The activated carbon catalyst regenerated through washing with a non-ionic surfactant in $H_{2}O$ at $90^{\circ}C$ and calcination under $N_{2}$ gas at $550^{\circ}C$ shows similar level of surface area and $NO_x$ removal efficiency with those of fresh catalyst.

• Food Science and Preservation
• /
• v.16 no.5
• /
• pp.719-725
• /
• 2009

We investigated the absorption characteristics of protein-bound polysaccharide powders of various molecular weights isolated from the mushroom Agaricus blazei Murill. The monolayer moisture content calculated using the GAB equation showed a higher level of significance than did the BET equation. The higher the water activity, the lower the isosteric heat of sorption. The fitness of the isotherm curve was shown to be in the order of the Khun, Oswin, Caurie and Henderson models. The prediction model equations for moisture content were established by use of ln(time), water activity, and temperature.

• Magazine of the Korea Concrete Institute
• /
• v.20 no.6
• /
• pp.28-35
• /
• 2008

The Burj Dubai Project will be the tallest structure ever built by man; when completed the tower will be more than 700 meter tall and more than 160 floors. While the early integration of aerodynamic shaping and wind engineering considerations played a major role in the architectural massing and design of this multi-use/residential tower, where mitigating and taming the dynamic wind effects was one of the most important design criteria, the material selection for the structural systems of the tower was also a major consideration and required detailed evaluation of the material technologies and skilled labor available in the market at the time Concrete was selected for its strength, stiffness, damping, redundancy, moldability, free fireproofing, speed of construction, and cost effectiveness. In addition, the design challenges of using concrete for the design of the structural system components will be addressed. The focus on this paper will also be on the early planning of the concrete works of the Burj Dubai Project.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.8
• /
• pp.425-430
• /
• 2019

Zinc coatings are widely used because of their environmental friendliness and high performance. In general, the coating temperature is a major factor in determining the coating layer thickness and coating quality. In the case of a zinc coating, a uniform and appropriate coating temperature is required. In this study, a thermal flow simulation of the air flow was performed to analyze the temperature distribution of a zinc spray coating room in a natural convection state. Using SolidWorks, modeling was performed for two spray coating rooms, a preheating room, and a drying room, and a thermal flow coupled analysis was performed using ANSYS-FLUENT. As a result of the analysis, the temperature distribution characteristics in the spray coating rooms were determined. It was found that the present temperature was below the target temperature of $25^{\circ}C$. Simulations were conducted for two different boundary conditions (one with a heater added and another with the open part closed). The simulation results show that the method of closing the open part is better than adding the heater.

• Journal of Climate Change Research
• /
• v.2 no.2
• /
• pp.107-113
• /
• 2011

In this research, we described the experimental results for the improvement of Potassium based sorbents. These sorbents have been actually used in the 0.5 MW $CO_2$ capture plant located in Hadong #3 Power Plant. Firstly, we had shaped two kinds of sorbents using a spray dryer. These sorbents applied magnetite & copper oxide as an additive. And the magnetite sorbent was evaluated more excellent relatively in the attrition index. Secondly, We had obtained TGA multicycle experimental results of the improved Potassium based sorbent which applied magnetite as an additive. Consequently, $CO_2$ sorption capacity had been sustained 5.5 wt% after 2nd cycle and attrition index was very excellent as 0.5%. Finally, we had investigated the characteristics of the sorbent following in properties of supporters. As a result, the sorption capacity of the KMO sorbent used base material as a supporter was appeared as 7.2 wt%.

• Journal of the Korean earth science society
• /
• v.44 no.2
• /
• pp.119-134
• /
• 2023

The synoptic, thermodynamic, and dynamic characteristics of a snowfall event that occurred in the Yeongdong region on March 1-2, 2021, were investigated. Surface weather charts, ERA5 reanalysis data, rawinsonde data, GK-2A satellite data, and WISSDOM data were used for analysis. The snow depth, exceeding 10 cm, was observed at four weather stations during the analysis period. The maximum snow depth (37.4 cm) occurred at Bukgangneung. According to the analysis of the weather charts, old and dry air was trapped within relatively warm, humid air in the upper atmosphere over the East Sea and adjacent Yeongdong region. This caused unstable atmospheric conditions that led to developing convective clouds and snowfall over Bukgangneung. In particular, based on the thermodynamic and kinematic vertical analysis, we suggest that strong winds attributable to the vertical gradient of potential temperature in the low layer and the development of convective instability due to cold advection played a significant role in the occurrence of snowfall in the Yeongdong region. These results were confirmed from the vertical analysis of the rawinsonde data.

• The Journal of Engineering Geology
• /
• v.32 no.1
• /
• pp.73-83
• /
• 2022

The factors influencing landslide occurrence were analyzed for six points on the upper slope and the 24 points on the lower slope along a forest road around Sangsan village in Chungju, Korea, where landslides have occurred due to heavy rainfall. In terms of physico-mechanical properties of the soil layer, the lower slope seemed to loosen owing to the higher porosity, lower unit weight, and lower friction angle compared with the upper slope. With respect to topographic characteristics, the lower slope had thicker regolith, more concave profile and plan curvatures, lower slope angles, and higher topographic wetness index values than the upper slope. Therefore, all the properties (except for the slope angle) appear to make the lower slope of the forest road more vulnerable to landslides than the upper slope. Apart from the physico-mechanical and topographic characteristics, inadequate maintenance and management of drainage facilities are also considered as further major factors influencing landslide occurrence.