• Journal of the Korean Wood Science and Technology
• /
• v.2 no.2
• /
• pp.5-7
• /
• 1974

1. This study indicates that above the fiber saturation point the drying rate can be increased with increasing the velocity of the air circutation, i.e., the drying rate of sample boards is proportional to the air velocity, but below the fiber saturation point, the effect of the velocity of air circulation is very low as shown in Figs. 1 and 2. 2. Under the controlled temperature and humidity in the kiln, the more the sample boards have moisture, the higher drying rate of it can be obtained. In other words, this means that even though in the case of drying various moisture content of wood, at the final drying stage, approximately the same percentage of moisture content of wood can be secured by employing the higher velocity of air circulation. 3. This study shows that the rate of drying in kiln changes distinctly at the fiber saturation point, i, e., above the fiber saturation point, the drying curve shows concave aginst the X axsis, but below the fiber saturation point, in the range from 30 percent of moisture content to 20 percent of moisture content, the curve shows convex as shown in Fig. 3. As the drying progresses, however, the drying curve shows concave again below 20 percent of moisture content. This means that inflection point of drying curve may be located clearly at the fiber saturation point, i.e., 30 percent of moisture content. As mentioned above, the 30 percent of moisture content of wood at which the inflectional point appears can be recognized as a critical point, i. e., the fiber saturation point at which all free water was removed from wood. The existence of inflectional point indicates that the evaporation of hygroscopic water in a cell wall is more difficult than the evaporation of free water in a cell cavity and the minor space of cell wall. The convex curve in the range of moisture content from 30 percent to 20 percent means that the evaporation of capillary condensed water has a tendency of the same rates of drying approximately, but as approaching to the 20 percent of moisture, the transfusion of moisture from wood becomes difficult because of having less moisture in cell wall. Below 20 percent of moisture content, the drying curve shows concave again, which means that it is difficult to remove the moisture located nearer to the surface of cellulose molecules and the surface bound water. These relations were revealed in Fig. 4. In comparison AC curve which does not have the two inflection points with BD curve which has two inflection points, i.e., Band D, they are mentioned already, by existence of the inflection points, the curve BD shows that the change of drying rate in the interval from 20 percent of moisture content to 30 percent of moisture content is not greater than in the case of the curve AC in the same interval. At the inflection point of 30 percent of moisture content, it can be noticed that the changing of the drying rate is very conspicuous. This phenomenon also can be recognized, as it is noticed by the Fig. 3, the drying rate from green to 30 percent of moisture content is very great. But the inclination of the curve is very slow from 30 percent of moisture content to 20 percent of moisture content, i.e., the inclination of the curve becomes almost horizontal lines. Acknowledgments Gratitude is expressed to Fred E. Dickinson, Professor of 'Wood Technology, School of Natural Resources, University of Michigan, USA for his suggestion to carry out this study.

• Food Science and Preservation
• /
• v.17 no.3
• /
• pp.358-364
• /
• 2010

Ginger was dried using maltodextrin or recycled dehydration liquid as dehydrating agents, and the quality of dried ginger was compared with that of freeze-dried and hot-air-dried samples in terms of color, moisture content, water activity, dehydration rate, rehydration rate, and sensory properties. Ginger prepared using molecular press dehydration (MPD) retained its original color. The dehydration rate increased when ginger was dried using a dehydrating agent. The rehydration rate was increased in ginger dried using such an agent. Both dehydration and rehydration rates were elevated with increasing concentrations of soluble solids in the dehydration liquid. The sensory qualities of ginger prepared using the MPD method were better than those of freeze-dried and hot air-dried samples. These results indicate that drying of ginger rhizomes using recycled dehydrating liquid is very efficient.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.1
• /
• pp.7-14
• /
• 2006

Three-dimensional distribution and variation of moisture content of boxed-heart square timber of Pinus densiflora was investigated to find the safe and rapid drying methods. As results, microwave-drying method could dry the boxed-heart square timber with sectional dimension of $150{\times}150mm$ under 10% moisture content (MC) within 72 hours with less surface checks, compared with hot-air drying. In case of microwave drying, the MC distribution during drying had a close relation with the initial MC distribution. In case of hot air drying, however, it was independent on the intial one except for the intial drying stage.

• Journal of Korean Society of Forest Science
• /
• v.37 no.1
• /
• pp.17-30
• /
• 1978

Press drying was used on italian poplar (Populus euamericana) to find the profitable means of drying. This study was designed to investigate the process of platen drying considering core temperature, drying time, current moisture content, drying rate, shrinkage and recovery, and green volume specific gravity, equilibrium moisture content and dimensional stability of press dried material and air dried material, The drying tests were conducted using 1.5 centimeter thick material at platen temperature of $175^{\circ}C$. The results were summarized as follows. 1. Core temperature was divided into three stages of drying characterized by period initial heating, plateau temperature and rising core temperature. Plateau temperature was 114 to $119^{\circ}C$. 2. The following predicting equations of drying time(y) in different core temperatures were developed for initial thickness($x_1$), initial moisture content ($x_2$) and final moisture content ($x_3$) 3. The predicting equaltion of current moisture content(u) was log u=4.658-0.060t as funtion of drying time(t) and that of drying rate(r) was log r=-2.797-0.049t. Current moisture content and drying rate of air drying were shown in figure 2. 4. The predicting equation of shrinkage in thickness direction(y) was log y=1.933+0.038t as function of drying time(t), and that of expansion in width direction was $y=-0.692+0.043t-0.001t^2$. 5. Thickness shrinkage was increased more than proportional at to pressure increase. Width shrinkage and thickness recovery was greatest at 35psi. 6. Green volume specific gravity of press dried material was 25% greater than that of air dried material. But equilibrium moisture content of press dried material was less 24% than that of air dried material. Antishrinkage efficiency of press dried material were obtained 27.7%.

• Journal of Forest and Environmental Science
• /
• v.10 no.1
• /
• pp.38-48
• /
• 1994

This study was carried out to estimate drying schedule of Fagaceae four species grown in Kangwon-Do by oven-drying at $100^{\circ}C$ which aimed to elucidate the characteristics such as current moisture content, drying process, initial check, collapse and internal check during drying. The results were summerized as follows ; Current moisture content of each board showed a rapid drying curve with the hight initial moisture content of board and species with the high initial moisture content took long to do drying. Appearance of checks for Quercus variabilis were extremely severe and estimated schedule was $T_5-C_2$. The shrinkage rate of grain direction was in the order of tangential direction > radial direction > longitudial direction and the shrinkage rate of oven-drying at $100^{\circ}C$ was bigger than normal shrinkage rate.

• Korean Journal of Food Science and Technology
• /
• v.21 no.1
• /
• pp.145-148
• /
• 1989

Shiitake mushrooms were dried by hot air, far infrared and freeze dryers in order to compare qualities after drying. When hot air drying was performed with the four temperature variations ranged from $45\;to\;70^{\circ}C$, there was tendency to increase volume retention but decrease rehydration ratio, as drying temperature increased. And the largest amout of 5'-GMP was contained in mushroom dried at $50^{\circ}C$. For far infrared drying, volume retentions were lower but rehydration ratios were higher, as compared with hot air drying at the same temperature. In freeze drying, freezing rate had no influence on volume retention but rehydration ratio was highest value when frozen at $-18^{\circ}C$. As shelf temperature increased(drying rate increased), rehydration ratio increased. Also, contents of 5'-AMP, 5'-GMP and 5'-XMP increased with the increase of freezing rate and drying rate.

• Geophysics and Geophysical Exploration
• /
• v.17 no.3
• /
• pp.121-128
• /
• 2014

As the permeability is an important parameter to characterize the ease with which a porous medium transmits fluids, it is usually obtained by fluid flow experiment using core samples. In order to measure the permeability, however, an experimental apparatus is required and it might take long measurement time, especially for tight samples. In this study, the relationship between permeability and porosity as well as drying rate has been investigated to predict the permeability without a series of measuring experiments. Porosity is measured by drying monitoring method, which measures weight variation continuously while drying surface-dried saturated sample, and drying rate is obtained from weight variation ratio with respect to the water saturation. The total of 6 Berea sandstone samples, which have a permeability range of 70 to 670 mD, were used in this work, and a new and empirical equation which could predict permeability of porous sandstone by using porosity and drying rate were obtained through regression analysis.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.6
• /
• pp.732-750
• /
• 2019

Air drying was carried out on 15 Korean red pine logs to provide a prediction model of the moisture content (MC) change in the wood during drying. The final MC was 17.4% after 880 days since the beginning of air drying in the summer for 6 Korean red pine logs with 68.7% initial MC. The final MC was 16.0% after 760 days since the beginning of air drying in the winter for 9 Korean red pine logs with 35.8% initial MC. A regression model with R-squared of 0.925 was obtained as a result of multiple regression analyses with initial MC, top diameter, temperature, relative humidity, and wind speed as independent variable and and MC change during air drying as dependent variable. The initial MC and top diameter, which is the characteristic of Korean red pine, have greater effect on the MC decrease during air drying compared to meteorological factors such as the temperature, relative humidity, and wind speed. Two-dimensional mass transfer analysis was performed to predict the MC distribution of Korean red pine logs during air drying. Two prediction models with different air drying days and different meteorological factors for the determination of the diffusion coefficient and surface emission coefficient were presented. The error between the different two methods ranged from 0.1 to 0.8% and the difference from the measured value ranged from 2.2 to 3.6%. By measuring the internal MC during air drying of Korean pine logs with various initial MC and diameter, and calculating the moisture transfer coefficient in wood for each meteorological condition, the error of the prediction model can be reduced.

• Korean Journal of Plant Resources
• /
• v.17 no.3
• /
• pp.219-226
• /
• 2004

Transplantings of onion (Allium cepa L.) seedlings are required for higher germinability and uniformity. This study was done to determine effects of various seed treatments (seed cleaning, priming, GA$_3$, prechilling, drying, and light quality during seed drying) on germination and seedling emergence. Nongwoodaego and Changnyungdaego were used as cultivars for checking seed germination, and two cultivars and Cheonjuguhyeonghwang were investigated with seedling production rate. Seed cleaning using water prior to the other treatments greatly increased germination rate. Priming with 200mM Ca(NO$_3$)$_2$ solution somewhat alleviated the germination rate while GA$_3$ did not. Prechilling had the highest rate among the treatments. Seed drying after prechilling enhanced the rate compared to non drying, and during drying the prechilled seeds red light illumination showed the greatest rate in comparison with dark, blue, and far-red ones. Seedling production rate was enhanced in sequential treatments of seed cleaning, prechilling for 3 to 5 days, and red light treatment during 6 hour seed drying.

• Journal of Forest and Environmental Science
• /
• v.12 no.1
• /
• pp.1-12
• /
• 1996

This study was carried out to estimate drying schedule of Fagaceae four species grown in Kangwon-Do by oven-drying at $100^{\circ}C$ which aimed to elucidate the characteristics such as current moisture content, drying process, initial check, collapse and internal check during drying following each board thickness (1.5cm, 2.5cm, 3.5cm, 4.5cm). The results were as follows; Current moisture content of each board showed a rapid drying curve with the high initial moisture content of board. With the high initial moisture content, the incease of board thickness and the slowness of changing rate of moisture content, species took long to do drying. Also, the initial conditions of drying had to be mild condition with the increase of board thickness.