• 한국환경과학회지
• /
• 제10권1호
• /
• pp.59-64
• /
• 2001

The effect of major operating parameters in spray drying sorber(=SDS) for automatic control for the simultaneous removal of acidic and organic gaseous pollutants from solid waste incinerator was performed. The field experiment was carried out in pilot scale test for the quantification of major operating parameters of hydrophilic and the hydrophobic pollutants. The removal efficiencies of $SO_2$and HCI in the 5wt% slurry condition were being increased with the increase of the stoichiometric ration which is the molecular ratio of lime to the pollutant concentration, and with the decrease of inflow flue gas temperature in the pilot SDS reactor. The removal efficiency along the height of spray drying sorber was closely related to the temperature profile, and more than 90% of total removal efficiency was achieved in an absorption region. For the removal of acidic gas the optimum operating condition considering the economics and a stable operation is the 5wt% of slurry concentration, 1.2 of stoichiometric ratio and 25$0^{\circ}C$ of inflow flue gas temperature. For the organic gases of benzene and toluene the removal efficiencies were 20-60% which is much lower than that of acidic gas. The best removal efficiency was obtained at 1.5 of stoichiometric ratio and 25$0^{\circ}C$ of inflow flue gas temperature. The organic\`s removal efficiency along the height of spray drying sorber was quite different from that of acidic gas, that is, more than 60% of the total removal efficiency for benzene and 90% of the total removal for toluene were achieved in the dried adsorption region, which was formed at the lower or exit part of the reactor.

• 한국대기환경학회지
• /
• 제6권1호
• /
• pp.85-96
• /
• 1990

Simultaneous removal efficiencies of hydrophilic and hydrophobic gaseous pollutants are experimentally determined, and the macroscopic removal mechanism of pollutants in a dry scrubber is analyzed using the extended model of three phase equilibrium distribution of pollutant at high temperatures that can describe the different morphological conditions of adsorbent and water at varying relative humidities. For the simplicity, the inside of spray dryer is divided into three regions of ; (1) absorption, (2) three-phase equilibrium, and (3) adsorption, and the removal efficiencies of each pollutants at three regions are observed at different experimental conditions to estimate the effects of important parameters of dry scrubber. The laboratory experiments simulate the three regions of spray dryer with the temperature control and thus evaporation rate of water from the slurry particle. $SO_2$ as a hydrophilic gaseous pollutant and vinyl chloride as a hydrophobic toxic gas are selected for the future field application to soid waste incineration, and the two types of slurry are made of the two sorbents ; 10 wt.% $Ca(OH)_2$, and 10 wt.% NaOH. Result of temperature effect shows the height of absorption plus three-phase region is decreased as the operation temperature is increased, which results in the lower removal efficiency of $SO_2$ but higher removal for vinyl chloride in the adsorption region of dry scrubber. The removal efficiency of $SO_2$ is higher by NaOH slurry than by $Ca(OH)_2$ slurry due to the hygroscopic nature of NaOH, while the removal of vinyl chloride is higher in $Ca(OH)_2$ case. From the analysis of redults using three-phase equilibrium distribution model, the effective two-phase partition coefficients can be obtained, and the possible extention in the application of the three-phase equilibrium model in a dry scrubber design has been demonstrated.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.9-15
• /
• 2019

Graphene is a fascinating material for fabricating flexible and transparent devices owing to its thickness and mechanical properties. To utilize graphene as a core material for devices, the transfer process of graphene is an inevitable step. The transfer process can be classified into wet and dry methods depending on the surrounding environment. The adhesion between graphene and a target substrate determines the success or failure of the transfer process. As the surface energy of graphene is an important parameter that provides adhesion, it is useful to estimate the surface energy to understand the mechanisms of the transfer process. However, the exact surface energy of graphene is still disputed because the wetting transparency of graphene depends on the polarity of the liquid and target substrate. Previously reported results use graphene transferred by the wet method. However, there are few reports on the surface energy of graphene transferred by the dry method. In this study, the surface energy of graphene transferred by the wet and dry methods is estimated. Wetting transparency occurs for certain combinations of liquids and substrates. For graphene on a polar substrate, the surface energy decreases by 25 and 35% for the wet and dry transfer methods, respectively. However, the surface energy of graphene on dispersive substrates decreases by ~10% regardless of the transfer method. In conclusion, the surface energy of graphene is $36{\sim}38mJ/m^2$, and differs depending on the transfer method and polarity of the substrate.

• 대한기계학회논문집B
• /
• 제24권4호
• /
• pp.589-598
• /
• 2000

A pilot-scale Spray Drying Sorber (SDS) system was set up to evaluate the effect of spray characteristics on the desulfurization yield. The size distribution and the Sauter Mean Diameters of slurry droplets were measured in advance using the optical size measurement system, Malvern 2600. The desulfurization yield of the drying chamber by size was measured for the conditions of inlet gas and spray injection. As a reagent, 10% limestone slurry of $Ca(OH)_2$ was treated with flue gas containing $SO_2$, and the combustion gas analyzer and gas detectors were attached to measure the $SO_2$ concentration. With a flow rate of 144 Nm3/h and a temperature range of $200{\sim}300^{\circ}C$, the experiments were performed for the Stoichiometric Ratio (SR) of 1.0 to 3.0 and droplet mean diameter of 6.5 to $34.3{\mu}m$. In case of smaller spray droplets, the desulfurization efficiency improved due to the increase of total droplet surface area, while the reduction in evaporation time reduced the contact time between the droplets and $SO_2$ gas. In some typical region of droplet diameter, this negative effect, reduction of contact time, became dominant and the desulfurization yield decreases the desulfurization yield in spite of the expansion in absorption area. These results revealed that there exists the optimal size of spray droplets for a given state, which is determined by the compromise between the total surface area of slurry droplets and the evaporation time of droplets. The measurements also indicated that the inlet temperature of flue gas changes the optimal injection condition by varying the driving force for evaporation. The results confirm that the effect of the evaporation time of slurry droplets should be considered in analyzing the desulfurization yield as well as the total surface area, for it is a significant aspect of the correlation with the capabilities of $SO_2$ absorption in wet droplets. In conclusion, the optimal condition of spray can be determined based on these results, which might be applied to design or scale-up of SDS system.

• 자원환경지질
• /
• 제40권5호
• /
• pp.661-673
• /
• 2007

안성 청룡사삼층석탑의 구성암석은 대부분 편마상 복운모 화강암과 세립질 화강암으로 이루어져 있다. 이 석탑은 거의 전면에 걸쳐 나타나는 부재의 균열과 결실이 탑의 구조안정성을 위협한다. 또한 표면의 무기오염물과 다양한 서식형태를 갖는 생물침해는 석재표면의 손상을 가중시키고 있다. 따라서 이 연구에서는 석탑에 대한 종합적인 비파괴훼손도 진단을 수행하고 이를 근거로 풍화를 저감시키기 위해 최소한의 보존처리를 수행하였다. 보존처리에서는 석탑의 전면에 걸쳐 자생하는 지의류 및 생물오염물을 건식 및 습식 세정하였으며, 과거 이 석탑의 보수에 사용되었던 노화된 콘크리트를 제거하고 합성수지를 이용하여 복원하였다. 부재사이에 삽입된 부식된 철편은 티타늄 강철 합금으로 교체하였으며, 모든 공정이 완료된 후에 석질 강화처리를 실시하였다. 또한 석탑의 지반과 주위환경을 보강하고 정비하였으며 관람객에 의한 손상을 제어하기 위한 보호시설을 설치하였다.

• 대한환경공학회지
• /
• 제39권8호
• /
• pp.449-455
• /
• 2017

기준공정과 개선대상공정 간의 투입물(Input, Material and energy), 배출물(Output, Product, Co-product), 환경오염물(Environmental emission) 데이터를 수집하고 공정 성과를 분석하였다. 이를 통해 환경적으로 주요한 투입물과 환경오염물을 파악하였다. 제조공정의 투입물과 환경오염물 간의 상관관계 분석을 통해 각 환경오염물에 대한 기여도가 큰 투입물을 파악하였다. 주요 환경오염물 처리 시, 경제적 최적화를 통한 종말처리공정 조합을 선형 프로그래밍 기법을 사용하여 규명하였다. 사례 연구로는 동일한 형태의 시멘트를 생산하는 EU와 국내 시멘트 제조공정을 선정하였다. 국내 시멘트 제조공정에서는 석탄이 주요 투입물로, 먼지, $SO_x$가 주요 환경오염물로 파악되었다. 제조공정의 투입물과 환경오염물 간의 다중회귀분석결과 석탄>원자재>석고 순으로 $CO_2$발생량에 기여도가 큰 것으로 나타났다. $SO_x$발생량의 경우 석탄의 기여도가 가장 컸으며, Dust 발생량의 경우 석고>원자재 순으로 기여도가 큰 것으로 나타났다. Dust 종말처리공정 최적화에서 전기집진기술 100%, 섬유필터기술 2.4% 조합이 최적이었다. $SO_x$종말처리공정 최적화에서는 건식첨가공정기술 100% 습식세정기술 25.88% 조합이 최적이었다. 이 연구의 특징은 제조공정에서 문제가 되는 주요 투입물과 환경오염물을 파악하는 방법을 제시하였다는 점이다. 또한, 기술적 경제적으로 최적의 조합인 종말처리공정 선정 방법을 제시하였다는 점이다.

• 헤리티지:역사와 과학
• /
• 제53권2호
• /
• pp.222-241
• /
• 2020

조선왕릉 태릉은 중종의 계비인 문정황후의 무덤으로 다양한 종류의 석조물(석물 24기, 봉분석재 144개)이 배치되어 있다. 이 석조물은 모두 중조립질의 흑운모화강암을 사용하여 제작하였다. 석조물의 주요 손상양상은 물리적 손상과 생물오염으로 확인되며 이 중에서 박리박락(145기), 입상분해(138기), 보수물질(156기)과 함께 생물오염인 조류(154기), 지의류(165기), 선태류(97기)가 높은 발생빈도를 보인다. 특히 생물학적 손상(조류)이 가장 심각한 상태(3등급 이상이 전체 석물의 94%)로 즉각적인 보존처리가 요구되며 부분적으로는 박리박락과 입상분해 등도 중장기적인 보존관리가 필요할 것으로 판단된다. 에코팁 경도와 초음파탐사 결과, 석재의 약 70%이상이 물성이 상당히 취약한 것으로 나타났다. 초분광 분석에서도 봉분석재 표면의 80% 이상에서 생물이 서식하는 것으로 분석되었으며 이 부분에는 P(인), S(황), Cl(염소), Ca(칼슘)이 높게 검출되었다. 이는 태릉이 수백 년 동안 야외에 위치하고 있어 물리적, 화학적 및 생물학적 요인 등에 의해 풍화작용을 받아 왔기 때문이다. 따라서 태릉 석조물 중 물리적 풍화등급이 높은 석물은 물성을 보강하기 위해 강화처리가 필요한 것으로 판단되며 생물은 석재의 손상을 유발할 수 있는 가능성이 높기 때문에 건식 및 습식 세정으로 제거해야 한다. 또한 보존처리 이후 생물의 재발생을 지연하기 위해서는 봉분에 흘러내린 토사를 정기적으로 정리해줄 필요가 있고 장기적으로 보존상태에 대한 모니터링이 필요하다.