• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.1
• /
• pp.46-53
• /
• 2017

This paper shows a length of wirecutter using an analysis based on Rotorcraft's control input and taxiing speed. In case of selecting an inappropriate length of wirecutter which applies to rotorcraft for safety, this causes a collision between blade and wirecuter, or an accident by wire. We review the control input which was used in development stage, and establish the conditions of control input which are needed in taxiing. Based on these conditions, we review the collision possibility between blade and wirecutter through analysis in case of 20, 40, 60 kts taxiing speed. Following, this result is verified by comparison with that of a simulation test in rotorcarft. Finally, in case of high collision possibility, we presented the downsize length to avoid the collision and increment of non-protective area in flight, simultaneously.

• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.14-21
• /
• 2010

Ion thruster is a kind of electrostatic thruster that use electrostatic field in order to accelerate ionized propellant. Ion thruster have characteristics of small thrust but very high specific impulse among the electric thrusters. High specific impulse can reduce propellant consumption significantly. So, ion thruster have advantage for long time and long distance mission. Recently, plans for space exploration is increasing gradually not only at traditional forward countries for space like USA, Russia and Europe, but also other countries like Japan, China and India. Exploration for superior planets and asteroids the propellant ratio can go up to about 99% when chemical propulsion is used as a cruising thruster. Therefore, latest space exploration vehicles use the ion thruster as main thruster for del-V burn and use monopropellant thrusters for attitude control. In this paper, the development process of preliminary ECR ion thruster and the ECR discharge test results will be presented.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.2 no.1
• /
• pp.121-131
• /
• 1999

Automatic Rudder Trim System(ARTS) is a device to reduce the pilot's work load for rudder trimming greatly required in varying abruptly aircraft's engine power. This paper represents a technical analysis and a design of control law of the ARTS. The control law of the ARTS is designed based on the analysis of aircraft's characteristics, system's requirements, and limitations. The control law is comprised of open loop control using the rudder trim map for a specific aircraft and closed loop control to compensate the error of the open loop control system. flight test results show that the ARTS can reduce pilot's work load for rudder trimming dramatically and can compensate the aircraft's transient yaw motion.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.8
• /
• pp.739-747
• /
• 2015

With rapid growth in the technologies and demand of Remotely Piloted Aircraft Systems (RPASs), integration of such systems into the existing airspace system is becoming an issue in many countries. RPAS have different flight performances, communication characteristics, separation assurance mechanisms, and human machine interfaces from manned aircraft. To establish rules and regulations for RPAS integration, it is important to understand the impacts of RPASs on the airspace system. A simulation system that integrates manned aircraft, air traffic control, and RPASs is developed in Inha University to investigate these impacts through Human-in-The-Loop (HiTL) simulations. Three conflict resolution scenarios between a manned aircraft and a Remotely Piloted Aircraft (RPA) were constructed and tested. Human factors such as the response times of pilots and controllers were measured and analyzed as well as the risk of each maneuver.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.9
• /
• pp.731-738
• /
• 2014

The mission of UAV has been expanded from a land to an ocean based on an enhancement of its technologies. Korea Aerospace Research Institute (KARI) also tries to expand the mission of tilt rotor UAV to an ocean, in which the shipboard landing of UAV is required. However the environment of an oceanic operation is severer than that of land due to salty, fogy, and windy condition. The landing point for automatic landing is not fixed due to movement of shipboard in roll, pitch, and heave. It makes the oceanic operation and landing of UAV difficult. In order to conduct an oceanic operation of tilt rotor UAV, this paper presents that the sea wave modeling according to the sea state is conducted and the shipboard landing of tilt rotor UAV under the sea wave is tested and evaluated through the flight simulator for UAV.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.23 no.9
• /
• pp.1123-1130
• /
• 2019

Simulation of the strong clutter occurring from the airborne radar is essential in the efficient development and performance evaluation of the aircraft radar system. If the efficient simulation of the clutter can be successful, algorithms can be proved and analyzed and also the performance evaluation is possible in the laboratory environment. Therefore, development and implementation of the airborne radar system can be achieved very economically in the effective way. However, the clutter simulation procedure is very difficult and tedious since the clutter environment changes in numerous ways as it depends on the flight path, direction of antenna beam, reflectivity of the surface, etc.. Thus, in this paper, the general Doppler spectrum model is suggested for efficient simulation of the various clutter environment. Also, it is shown that the various type of clutter in time domain can be generated easily by changing and adjustment of parameters in the general Doppler spectrum model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.9
• /
• pp.1093-1098
• /
• 2013

A single-crystal sapphire is used as a transparent bulletproof window material; however, few studies have investigated the dynamic behavior and fracture properties under high-speed impact. High-speed and high-resolution sequential images are required to study the interaction of the bullet with the brittle ceramic materials. In this study, a device is developed to capture the sequence of high-speed impact/penetration phenomena. This system consists of a speed measurement device, a microprocessor-based camera controller, and multiple CCD cameras. By using a linear array sensor, the speed-measuring device can measure a small (diameter: up to 1 2 mm) and fast (speed: up to Mach 3) bullet. Once a bullet is launched, it passes through the speed measurement device where its time and speed is recorded, and then, the camera controller computes the exact time of arrival to the target during flight. Then, it sends the trigger signal to the cameras and flashes with a specific delay to capture the impact images sequentially. It is almost impossible to capture high-speed images without the estimation of the time of arrival. We were able to capture high-speed images using the new system with precise accuracy.

• Journal of the Korean Vacuum Society
• /
• v.17 no.4
• /
• pp.270-277
• /
• 2008

Vacuum is any air or gas pressure less than a prevailing pressure in an environmental or, specifically, any pressure lower than the atmospheric pressure and is used by a wide variety of scientists and engineering - including clean environment, thermal insulation, very long mean free path, plasma, space simulation[1]. The space environment is characterized by such a severe condition as high vacuum, and very low and high temperature. Since a satellite will be exposed to such a space environment as soon as it goes into its orbit, space environmental test should be carried out to verify the performance of the satellite on the ground under the space environmental conditions. A general and widely used method to simulate the space environment is using a thermal vacuum chamber which consists of vacuum vessel and thermally controlled shroud. As indicated by name of vacuum chamber, the vacuum technology is applied to design and manufacture of the thermal vacuum chamber. This paper describe the vacuum technology which is applied to space business.

• Journal of Satellite, Information and Communications
• /
• v.6 no.1
• /
• pp.37-44
• /
• 2011

COMS(Chollian) satellite which was launched on June 26, 2010 has three payloads for Ka-band communications, geostationary ocean color imaging and meteorological imaging. In order to make efficient use of the geostationary satellite, a concept of mission operations has been considered from the beginning of the satellite ground control system development. COMS satellite mission operations are classified by daily, weekly, monthly, and seasonal operations. Daily satellite operations include mission planning, command planning and transmission, telemetry processing and analysis, ranging and orbit determination, ephemeris and event prediction, and wheel off-loading set point parameter calculation. As a weekly operation, North-South station keeping maneuver and East-West station keeping maneuver should be performed on Tuesday and Thursday, respectively. Spacecraft oscillator updating parameter should be calculated and uploaded once a month. Eclipse operations should be performed during a vernal equinox and autumnal equinox season. In this paper, operational validations of the major functions in COMS SGCS are presented for the first three month of in-orbit test operations. All of the major functions have been successfully verified and the COMS SGCS will be used for the mission operations of the COMS satellite for 7 years of mission life time and even more.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.5
• /
• pp.97-105
• /
• 2017

An air-burst munition is limited in space, so there is a limit on the size of the fuze and the amount of ammunition. In order to increase a firepower to a target with limited ammunition, it is necessary to concentrate the firepower on the ground instead of the omnidirectional explosion after flying to the target. This paper explores the design and verification of a ground-detection sensor that detects the direction of the ground and determines the flight-distance of an air-burst munition using a single axis geomagnetic sensor. Prior to the design of the ground detection sensor, a geomagnetic sensor model mounted on the spinning air-burst munition is analyzed and a ground-detection algorithm by simplifying this model is designed. A high speed rotating device to simulate a rotation environment is designed and a geomagnetic sensor and a remote-recording system are fabricated to obtain geomagnetic data. The ground detection algorithm is verified by post-processing the acquired geomagnetic data. Taking miniaturization and low-power into consideration, the ground detection sensor is implemented with analog devices and the processor. The output signal of the ground detection sensor rotating at an arbitrary rotation speed of 200 Hz is connected to the LED (Light Emitting Diode) in the high speed rotating device and the ground detection sensor is verified using a high-speed camera.