• Journal of the Korean Wood Science and Technology
• /
• v.15 no.4
• /
• pp.45-58
• /
• 1987

This study was carried out to improve the physical and mechanical properties of Pupulus alba $\times$ glandulosa treated by the heat and compression. The results obtained were as follows. 1. The specific gravity of the wood was conspicuously increased by the lincreasing of pressing level. 2. The shrinkage of the wood was increased. by the increasing of pressing level. The radial shrinkage was 6.41-8.81%, the tangential shrinkage was 8.98-19.81 %, and the longitudinal shrinkage was 1.46-1.91 %. Comparing to the untreated stock, the rate of increase was 48.7-104.4% in radial direction. 1.7-124.4% in tangential direction and 60.4-109.9% in longitudinal direction, respectively. 3. The rate absorption of 30% compressed stock was Similar to that of untreated stock. but the rate of absorption of 40 % or more compressed stock was increased highly. 4. The thickness swelling of the wood was not changed in radial direction at pressing level, but was conspicuously increased in tangential direction under the pressing level of 40% and 50%. 5. The heat and compression treatment affected on the mechanical properties of the wood. The longitudinal compressive strength was increased under the pressing level of up to 40%, but was decreased under the pressing level of 50%. The bending strength was not changed under the compression percentage of up to 30%, but was decreased under the pressing level of 30% or more. And, the absorbed energy in impact bending was increased to 128% under the pressing level of up to 30%, but was decreased under the pressing level of 30% or more. Conclusionly, the mechanical properties of the wood was improved by the heat and compression treatment, but the strength of the wood was decreased under the pressing level of a certain level or more(in this study, pressing level of 30% or more). This was because of the wood deterioration due to the deformation(shrinkage, crack, failure) of wood tissues induced by the heat and compression treatment, the heat analysis of wood components induced by the heating, and the drop of the degree of polymerization.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.4
• /
• pp.323-332
• /
• 2010

Petroleum-based adhesive resins have extensively been used for the production of wood panels. However, it is necessary to develop environmentally friendly adhesive resins due to the increase of manufacturing cost and the environmental issue, such as the emission of volatile organic compounds, of the pertroleum-based adhesive resins. This study was conducted to formulate environmentally friendly adhesive resins using by rapeseed flour (RSF), which is the by-product of bio-diesel produced from rapeseed, for replacing petroleum-based adhesives with them. To formulate RSF-based adhesive resins, RSF was hydrolyzed in de-ionized water, 1% and 3% sodium hydroxide solutions. As a crosslinking agent, PF prepolymers were prepared with 1.8, 2.1 and 2.4 mol formaldehyde and 1 mol phenol (1.8-, 2.1- and 2.4-PF), and then mixed with RSF hydrolyzates to complete the formulation of RSF-based adhesive resins. The RSF-based adhesive resins were applied to fabricate 3-ply plywood panels. The solid content of RSF-based adhesive resins were ranged from 26.08% to 36.12% depending on the hydrolysis condition of RSF and PF prepolymer type with a high viscosity. The tensile shear strength and wood failure of plywood fabricated with RSF-based adhesive resins exceeded a minimum requirement of KS standard for ordinary plywood regardless of the hydrolysis condition of RSF and PF prepolymer type. Formaldehyde emissions of the plywood panels fabricated with 1.8-PF and RSF hydrolyzates were lower than that of E0 specified in the KS standard. Based on the results, RSF might be used as a raw material of environmentally friendly adhesives for the production of plywood panels, but further researches - the increase of solid content of RSF-based adhesives for reducing press time and the microscopic observation of plywood specimen for identifying the relationship between tensile shear strength and the penetration of adhesives into wood structure - are required to commercialize the RSF-based adhesives.

• Journal of Plant Biotechnology
• /
• v.33 no.3
• /
• pp.171-184
• /
• 2006

According to ISAAA report, the global area of genetically modified (GM) crops increased more than 50 fold during the ten-year period from 1996 to 2005 with a sustained double-digit growth rate of 10%. This biotechnology adoption is one of the highest rates of technology adoption in agriculture history and this phenomenon indicates that the industrial value of the GM crops is highly perspective. In addition, the year 2010, 60% of cereal seeds in the global market would be GM or biotechnology related seeds so that the GM crop regards as the second green revolution that could provide a huge impact to food and agriculture. Nevertheless, there has not been any GM variety ever successfully commercialized in Korea and even none of the GM crops has ever been approved for safety testing by risk assessment. This seems that Korean agriculture industry might be indeed lost in the war of future seed market. However, lots of evidence show that Korean scientists have established advanced technologies and protocols to develop GM crops for last 20 years. Actually there have been many cases of successful transformation of crops that were previously known very difficult in transforming. Therefore, Korean agbiotechnology arena firmly holds an infrastructure for developing GM crops with a superior technology. Then what were the problems? Why has even a single GM crop not been commercialized in Korea? The tardiness shown by business in adopting the GM crop is caused by many factors: academical weakness, poor research funding, short knowledge of risk assessment, public concern, no successful experience, lack of professional leaders on GM variety development, lack of systems toward industrialization and inappropriate target transgenes from the beginning. In order to catch up in the race for the new green industry, each one of us in private sectors alongside academia and national research institutes needs to focus altogether on what can be done best in terms of choosing crops, investing fund and establishing a road map for commercialization of GM crops.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.14 no.2
• /
• pp.7-16
• /
• 1986

This study was carried out to investigate the effects of such erosion control measures as sowing, planting and small earth structures on the soil and vegetation. In order to study the changes in soil and vegetation, 36 plots were surveyed from 1981 to 1982 in the large erosion control area which is restored last 20 years. The factors which were measured included vegetation coverage, tree growth, number of species, soil depth, soil consistancy, and Chemical properties of soil. The results were as follows; 1) Maximum coverage of the overstory and understory was attained 7 years after the initiation of erosion control. So the overstory need to be tended and pruned. 2) Diversity of species increased until age 6 after which it began to decrease. 3) In order of tree growth, black locust was the fastest, followed by siberian alder and pitch pine. The initial growth of black locust, though the best among the 3 tree stop., decreased rapidly year by year. At the same time, siberian alder and pitch pine grew well until 12 and 6 years after the initiation of erosion control respectively. 4) Fifty percent of the initially planted trees died within 8 yeard. The mortality of siberian alder occurred until the 20th year while the mortality of pitch pine stopped after 10 years. Thereafter 500 trees per hectare were maintained. 5) The soil depth in A and B horision increased by 2cm annually during 20 years. The soil consistency also decreased rapidly until 7th year. The physical soil properties of the rehabilitated areas were improved after the 14th year. 6) The soil pH tend to decrease from 5.3 during the first year to 5.1 during the twentieth year. 7) The organic matter and nitrogen content in the soil were increased by fertilization but after 20 years these nutrients are still deficient for normal tree growth. 8) The phosphorous content in the soil was high in the first year but the longer the period after the initiation of erosion control the lese the content of phosphorous. 9) The biomass of black locust was the highest and increased continuously. The biomass of siberian alder on the contrary decreased from the 15th year because the number of trees in this place was very low. The total biomass in the twentieth year after erosion control initiation was 105.7 ton per hectare.

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.2
• /
• pp.57-65
• /
• 2000

Objective of research is obtain fundamental data of carbonized wood wastes for soil condition, de-ordorization, absorption of water, carrier for microbial activity, and purifying agent for water quality of river. The carbonization technique and the properties of carbonized wood wastes(wood-based materials) were analyzed. Proximate analysis showed the wood-based materials contains 0.37~2.27% ash, 70~74% volatile matter, and 17~20% fixed carbon. As carbonization temperature was increased, the charcoal yield was decreased. However, no difference in charcoal yield was found due to time increase. The specific gravity after the carbonization decreased about 30~40% comparing to green wood. The charcoal had 1.08~4.18% ash, 5.88~13.79% volatile matter, and 80.15~90.94% fixed carbon. The pH of plywood and particleboard(pH 9 at $400^{\circ}C$, pH 10 at $600^{\circ}C$ and $800^{\circ}C$) made charcoals was higher than that of fiberboard. The water-retention capacity was not affected by the carbonization temperature and time. The water-retention capacity within 24h was about 2~2.5 times of sample weight, and the Equilibrium moisture content(EMC) became 2~10% after 24h. EMC of charcoal from the thinned trees were 9.40~11.82%($20^{\circ}C$, RH 90%), 6.87~7.61%($20^{\circ}C$, RH 65%), and 1.69~2.81%($20^{\circ}C$, RH 25%). EMC of charcoal from the wood-based materials under $20^{\circ}C$, relative humidity(RH) 90% was similar to EMC of charcoal from the thinned trees(9~11 %). However, under $20^{\circ}C$, RH 25.65%, EMC of charcoal from the wood-based materials were higher(2~3%) than EMC of charcoal from the thinned trees. Every charcoal from the wood-based materials fulfilled the criteria in JWWA K 113-1947.

• The Journal of Engineering Geology
• /
• v.29 no.1
• /
• pp.51-68
• /
• 2019

This study performs to evaluate adaptability of seashore filtering type seawater-intake which adapts dua1 filter well alternative for direct seawater-intake. This study varies filter condition of seashore free surface aquifer which is composed of sand layer then installs real size dual filter well and single filter well to evaluate water permeability and proper pumping amount according to filter condition. According to result of step aquifer test, it is analysed that 110.3% synergy effect of water permeability coefficient is happened compare to single filter since dual filter well has better improvement. dual filter has higher water permeability coefficient compare to same pumping amount, this means dual filter has more improved water permeability than single filter. According to analysis result of continuous aquifer test, it is evaluated that dual filter well (SD1200) has higher water permeability than single filter well (SS800) by analysis of water permeability coefficient using monitoring well and gauging well, it is also analysed dual filter has 110.7% synergy effect of water permeability coefficient. As a evaluation result of pumping amount according to analysis of water level dropping rate, it is analysed that dual filter well increased 122.8% pumping amount compare to single filter well when water level dropping is 2.0 m. As a result of calculating proper pumping amount using water level dropping rate, it is analysed that dual filter well shows 136.0% higher pumping amount compare to single filter well. It is evaluated that proper pumping amount has 122.8~160% improvement compare to single filter, pumping amount improvement rate is 139.6% compare to averaged single filter. In other words, about 40% water intake efficiency can be improved by just installation of dual filter compare to normal well. Proper pumping amount of dual filter well using inflection point is 2843.3 L/min and it is evaluated that daily seawater intake amount is about $4,100m^3/day$ (${\fallingdotseq}4094.3m^3/day$) in one hole of dual filter well. Since it is possible to intake plenty of water in one hole, higher adaptability is anticipated. In case of intaking seawater using dual filter well, no worries regarding damages on facilities caused by natural disaster such as severe weather or typhoon, improvement of pollution is anticipated due to seashore sand layer acts like filter. Therefore, It can be alternative of environmental issue for existing seawater intake technique, can save maintenance expenses related to installation fee or damages and has excellent adaptability in economic aspect. The result of this study will be utilized as a basic data of site demonstration test for adaptation of riverside filtered water of upcoming dual filter well and this study is also anticipated to present standard of well design and construction related to riverside filter and seashore filter technique.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.3
• /
• pp.68-87
• /
• 1982

In Korea, this is the situation at moment that the total demand of timber in 1972 is more than 5 million cubic meters. On the other hand, however, the available domestic supply of timber at the same year is only about, 1 million cubic meters. A great unbalancing between demand and supply of timber has been prevailing. To solve this hard problem, it has been necessitiated to build up the forest stocks as early as possible with fast grown species such as poplar. Under circumstances, poplar plantations which have been carryed on government and private have reached to large area of 116,603 hectors from 1962 up to date. It has now be come a principal timber resources in this country, and required the basic study on various properties of wood for it's proper utilization, since it has not been made of any systematic study on the properties of Populus grown in Korea. In order to investigate the properties such as anatomical, physical and mechanical properties of nine different species (P. euramericana Guiner I-214. P. euramericana Guiner I-476, P. deltoides Marsh, P. nigra var. italica (Muchk) Koeme, P. alba L.,P. alba $\times$ glandulosa P. maximowiczii Henry, P. koreana Rehder, P. davidiana Dode) of poplar for their proper use and development of new ways of grading processing and quality improving, this study has been made by the Forest Research Institute.

• Korean Journal of Soil Science and Fertilizer
• /
• v.16 no.1
• /
• pp.42-49
• /
• 1983

In order to find out the possibility of predicting fertilizer K requirement from the K supplying capacity of soil, the relative K activity ratio, Kas/kai, the potential buffering capacity of $K^+$ ($PBC^k$ ; the liner regression coefficient) and its activity ratio ($AR^k_o$ ; $^{k+}$/${\sqrt{Ca^{+2}+Mg^{+2}}}$ in mol/l) at ${\delta}K$ = O, in the Q/I relationships of Beckett(1964), were determined for the soils before flooding and the samples taken at heading stage of transplanted rice in pot experiment. These parameters assumed as the K supplying capacity of soils were subjected for the investigation through correlation stady between themselves and other factors such as grain yield or the amounts of $K_2O$ uptake by rice plant at harvest. The results may be summarized as follows; 1. The potassium supplying power of the flooded soil was considered to be ruled by the amounts of exchangeable K before flooding, since there was little change in exchangeable K concentration from no-exchangeable K during the incubation periods of 67 days. 2. The $PBC^k$ values, in soils before flooding were 0.027, 0.014 and 0.009, where as the $AR^k_o{\times}10^{-3}$ values were 9.1, 7.6, and 15.4, respectively, in clay, loamy and sandy loam soils. 3. The $PBC^k$ values, determined in the soil samples taken at heading stage, varied little compared with the values of orignal soil, regardless of those different fertilizer treatments and textures, showing the possibility of using them as a factor for the improvement of soil to increase the efficiency of fertilizer K. 4. The significant yield responses to potassium fertilizer application were observed wherever the $AR^k_o$ values in soil at heading stage drop down to the original $AR^k_o$ values, regardless of any levels of fertilizer application. 5. The higher correlations between the gain yield or the amounts of $K_2O$ uptake and by the use of both soil factors of $PBC^k$ and $AR^k_o$ at heading stage were observed compared with the use of any single factor. 6. The Kas/Kai value in the soil, estimated prior to the experiment, had high possitive correlation with the $AR^k_o$ determined in the soil at heading stage and could be used as a soil factor for predicting potassium fertilizer requirement.

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.2
• /
• pp.25-31
• /
• 1974

1. Various gluing qualities applying Resorcinol Plyophen #6000 were studied on aiming the strength relationships of laminated woods resulted by single species [poplar (Populus deltoides), larch(Larix leptolepis)], mixed species of (poplar and larch), preservatives, treated poplar the scarf joint with mixed species of poplar and larch and the scarf joint treated with preservatives. 1. 1 On the block shear and on the DVL tension test, the mean wood failure ratio showed an excellent value i.e., above 65% and the tangential strength for larch was higher than that of radial, but it was reversed for poplar as shown in Tables 1 and 2. 1. 2 The lamina treated with Na-PCP reduced slightly the strength but the limited strength allowed for manufacturing laminated wood was not influenced by treating Na-PCP as shown in Tables 3 and 4. 1. 3 The safe scarf ratio in the plane scarf joint was above 1/12 for larch and 1/6 for poplar regard less of the chemical treatment or untreatment as shown in Tables. 5, 6, 7 and 8. 2. In the normal and boiled state, the gluing quality of the laminated wood composed of single[poplar (Populus deltoides), larch (Larix leptolepis)] and double species (poplar and larch) glued with Resorcinol Plyophen #6000 were measured as follow, and also represented the delamination of the same laminated wood. 2.1 The normal block shear strength of the straight and curved laminated wood (in life size) were more than three times of the standards adhesion strength. And, the value of the boiled stock was decreased to one half of the standard shear adhesion strength, but it was more than twice the standard strength for the boiled stock. Thus, it was recognized that the water resistance of the Resorcinol Plyophen #6000 was very high as shown in Tables 9 and 10. 2. 2 The delamination ratio of the straight and curved laminated woods in respect of their composition were decraesed, in turn, in the following order i. e., larch, mixed stock (larch+poplar) and poplar. The maximum value represented by the larch was 3.5% but it was below the limited value as shown in Table 11. 3. The various strengthes i.e., compressive, bending and adhesion obtainted by the straight laminaced wood which were constructed by five plies of single and double species of lamina i. e., larch (Larix leptolepis) and poplar (Populus euramericana), glued with urea resin were shown as follows: 3. 1 If desired a higher strength of architectural laminated wood composed of poplar (P) and larch (L), the combination of the laminas should be arranged as follows, L+P+L+P+L as shown in Table 12. 3.2 The strength of laminated wood composed of laminas which included pith and knots was conside rably decreased than that of clear lamina as shown Table 13. 3.3 The shear strength of the FPL block of the straight laminated wood constructed by the same species which were glued with urea adhesives was more than twice the limited adhesion strength, thus it makes possible to use it for interior constructional stock.

• Korean Journal of Agricultural Science
• /
• v.22 no.2
• /
• pp.170-179
• /
• 1995

This study was conducted to investigate the genetic constitution of blood proteins and enzymes in 238 Korean Native cattle reared at Korean Native Cattle Breeding Center, National Livestock Cooperative Federation. The genetic polymorphisms of post-transferrin-2(pTf-2), transferrin(Tf), post-albumin(pAlb), albumin(Alb), ceruloplamin(Cp), amylase-I(Am-I) and hemoglobin(Hb) were analyzed by using PAGE(polyacrylamide gel electrophoresis) and STAGE(starch gel electrophoresis). The genotypes and gene frequencies were estimated at these loci for each blood proteins and enzymes. The results obtained from this study were summarized as follows : 1. The pTf-2 locus were identified to be genetically controlled by codominant alleles designated pTf-2 F and S, and the distribution of genotypes were 46.22, 46.64 and 7.14% for pTf-2 FF, FS and SS types, and the gene frequencies of the pTf-2 F and S allele were 0,695 and 0.305, respectiveley. 2. The Tf locus were found to be controlled by Tf A, D1, D2 and E alleles, and the distributioin of genotypes were 0.84, 13.87, 13.03, 10.92, 22.27, 12.61, 2.94, 15.51, 6.72 and 1.68% for Tf AA, AD1, AD2, AE, D1D1, D1D2, D1E, D2E and EE types, and the gene frequencies of Tf A, D1, D2 and E were 0.197, 0.430, 0.191 and 0.081, respectively. 3. The pAlb locus were observed to be controlled by two alleles, pAlb F and S, and the distribution of genotypes were 42.86, 33.19 and 23.95% for pAlb FF, FS and SS types, and the gene frequencies were 0.595 and 0.405 for Tf F and S allele, respectively. Also the gene frequencies of Alb was 1.000 of Alb A allele. 4. The Cp locus were identified to be controlled by Cp F and S allele, and the distribution of genotypes were 23.11, 34.87 and 42.02% for Cp FF, FS and SS types, and the gene frequencies were 0.405 and 0.595 for Cp F and S allele, respectively. 5. The Am-I locus were observed to be genetically controlled by Am-I B and C allele, and the distribution of genotypes were 51.26, 16.81 and 31.92% for Am-I BB, BC and CC types, and the gene frequencies of Am-I B and C alleles were 0.597 and 0.403, respectively. 6. The Hb locus were found to be controlled by Hb A and B alleles, and the distribution of genotypes were 93.19, 16.39 and 0.42% for Hb AA, AB and BB types, and the gene frequencies of Hb A and B alleles were 0.914 and 0.086, respectively.