• Journal of the Korean Wood Science and Technology
• /
• 제22권4호
• /
• pp.43-50
• /
• 1994

본 연구는 침엽수재를 사용한 손가락결합부재의 강도 및 감쇠특성을 측정함으로서 문창틀재로의 사용가능성을 시험하기 위하여 수행하였다. 손가락결합부 시험편의 형태는 손가락부분의 길이와 경사도에 따라서 다섯가지로 제작하였다. 하중은 4개의 하중단계를 갖는 양방향휨으로 가하였으며 각각의 하중단계는 3개의 하중주기로 구성되었다. 손가락결합부의 파괴특성을 분석하기 위하여 감쇠시험 과정에 AE신호를 측정하였다. MOE는 시험편의 형태와 뚜렷한 관련을 갖고 있지 않으나, MOR은 손가락부분의 경사도가 증가될수록 감소되는 뚜렷한 관계를 나타내었다. 감쇠비는 하중단계가 증가될수록 감소되었으나 파괴직전의 단계에서는 증가되는 경향을 나타내었다. 하중방향에 대하여 수직한 방향의 손가락결합부재가 수평방향부재보다 더 높은 강도를 나타내었다. 60dB 이상의 AE신호는 목재 또는 접착층의 파괴에 의하여 발생되는 것으로 분석되었다. 완전한 파괴가 발생하는 경우에는 100dB 이상의 AE신호가 발생하였다.

• Magazine of the Korea Concrete Institute
• /
• 제4권2호
• /
• pp.111-118
• /
• 1992

본 연구는 실리카흄을 혼화재료로 사용하여 1200kg/$ extrm{cm}^2$정도의 초고강도 콘크리트를 제조하였으며 이에 대한 재료특성을 실험 및 보부재의 휨거동을 실험을 실시 비교 분석하였다. 재료특성 실험으로는 기본적인 강도 시험, 파괴음 측정에 의한 AE실험 그리고 수은압입법에 의한 세공실험을 실시하였다. 초고강도 콘크리트의 재료특성치는 ACI 363의 고강도 콘크리트 재료특성 결가보다 크게 나타났으며 압축강도와 미세공극량은 선형적으로 비례하였다. 보부재의 휨특성을 파악하기 위해 인장철근비 변화, 전단보강근의 유무 및 철근 표면형상의 변화 등을 실험인자로 하였으며 각각의 현상을 비교분석함으로써 균열성상에 따른 하중-변위 관계, 중립축 이동에 따른 부재거동 및 응력블록의 변화에 관하여 비교 고찰하였다. 초고강도 콘크리트 사용한 보부재의 경우 중립축 상승으로 단면의 압축영역은 매우 작아져 급격히 압축파괴되는 경향을 보였으며 응력블록 형태는 삼각형의 분포를 보였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• 제28권4A호
• /
• pp.537-548
• /
• 2008

Recently, the prestressed unbonded concrete structures are increasingly being built. The mechanical behavior of prestressed concrete beams with unbonded tendon is different from that of normal bonded PSC beams in that the increment of tendon stress was derived by whole member behavior. The purpose of the present paper is therefore to evaluate the flexural behavior and to propose the equation of ultimate tendon stress by performing static flexural test according to span/depth, concrete compression strength, reinforcement ratio and the effect of existing bonded tendon. From experimental results, for cracking, yielding and ultimate load, the effect of reinforcement ratio was more effective than concrete compression strength, and the beams having high strength concrete had a good performance than having low concrete, but there was no difference between high strength and low strength. And as L/dp was larger, test beams had a long region of ductility. This means that unbonded tendon has a large contribution after reinforcement yielding. Especially, the equation of ACI-318 was not match with test results and had no correlations. After analysis of test results, the equation of ultimate unbonded tendon stress without slip was proposed, and the proposed equation was well matched with test results. So the proposed equation in this paper will be a effective basis for the evaluation of unbonded tendons without slip, analysis and design.

• Journal of the Korean Geophysical Society
• /
• 제9권4호
• /
• pp.301-310
• /
• 2006

In this short paper, an elasto-plastic repair and retrofit element is developed for the investigation of the seismic performance of damaged reinforced concrete members. The developed element is capable of reflecting the increased characteristics due to both repair and retrofitting for degraded strength and stiffness of the members. The element having both birth and death time can freely be activated within the user-defined time intervals during static and dynamic time-history analysis. Comparative studies are conducted for reinforced concrete members being repaired and retrofitted. Analytical predictions including the developed element display reasonable correlation with experimental results. In short, it is concluded that the developed element is capable of providing salient features for the healthy assessment of seismic performance of RC members being repaired and retrofitted.

• Journal of the Korea institute for structural maintenance and inspection
• /
• 제18권3호
• /
• pp.125-132
• /
• 2014

Steel fiber is a effective composite for crack resistance and improve structural performance under tensile loading. This study presents an evaluation of crack resistance and structural performance in cement mortar with steel fiber and expansion agent through internal chemical prestressing. For this work, cement mortar samples with 10% replacement of cement binder with CSA (Calcium-Sulfo-Aluminate) expansion agent and 1% volume ratio of steel fiber are prepared. Including basic mechanical properties, initial cracking load and fracture energy are evaluated in cement mortar beam with notch. Initial cracking load and fracture energy in cement mortar with CSA and steel fiber increase by 1.75 and 1.41~1.53 times compared with those in cement mortar with steel fiber. With optimum mix design for steel fiber and CSA expansive agent, the composite with chemical prestressing can be applied to various members and effectively improve crack resistance to external loading.

• Journal of Korean Society of Steel Construction
• /
• 제30권1호
• /
• pp.1-12
• /
• 2018

A curved member should resist bending and torsional moments simultaneously even though the primary load is usually supposed to be gravitational load. The torsional moment causes complicate stress state and also can result in early yielding of material to reduce member strength. According to analysis results, the strength of a curved member that has 45 degrees of subtended angle could decrease more than 50% compare to straight girder. Nevertheless, there have been very few of researches related with ultimate strength of curved girders. In this study, various kinds of stiffness about bending, pure torsion and warping were considered with a number of models in order to verify the main factor that affects ultimate behavior of curved girder. Lateral and rotational displacement of curved member were introduced as lateral-torsional-vertical behavior and bending-torsional moment interaction curve was derived. Finally, a strength equation for ultimate moment of horizontally curved steel I-girders subjected to equal end moments based on the interaction curves. The equation could take account of the effect of curvature, unbraced length and sectional properties.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• 제23권5호
• /
• pp.543-550
• /
• 2010

Earthquake resistant design should provide a description of the structural failure mechanism under earthquakes as well as satisfy the requirement of other designs, e.g. design strengths of each structural member should be equal or greater than the required strengths. The reason of such a requirement is the randomness of seimic loads different from other loads. In this study, a typical bridge is selected as an analysis bridge and the procedure is given to get the ductile failure mechanism through connection design. It is shown with the procedure that the earthquake resistant capacity can be ensured within structural member's strengths required by other designs, without cost raise by strength increase of structural members or by use of shock absorbing device e.g. shock transfer unit.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• 제32권1A호
• /
• pp.55-64
• /
• 2012

Experimental investigation on the structural behavior of steel fiber-reinforced ultra high performance concrete (UHPC) beams subjected to shear are presented. Six tests carried out on simply supported I-beams under concentrated loads are presented. The parameters varied were the volume fraction of the fibers (1.0, 1.5 and 2.0%) and shear span-effective depth ratio (2.5, 3.4). The test results indicated that ultimate shear strength increased with increasing fiber volume, and that ultimate shear strength decreased with increasing shear span-effective depth ratio. In addition, applicability of predictive equations for evaluating the ultimate shear strength of steel fiber-reinforced UHPC beams are estimated based on the test results. The comparison between computed values and the experimentally observed values are shown to validate the proposed theoretical equations. It is found that predictions by using AFGC and JSCE recommendations provide the most accurate estimates of shear strength of steel fiber-reinforced UHPC beams.

• Journal of the Korea institute for structural maintenance and inspection
• /
• 제22권2호
• /
• pp.26-33
• /
• 2018

This paper presents experimental and analytical results on flexural behavior of flexural members made of SIFCON. Twelve SIFCON beams were subjected to bending tests and their flexural behavior was evaluated. Experimental variables included steel fiber type, presence of tensile reinforcement, and height of section. The specimens using Type-B steel fibers, which had better pullout resistance than Type-A steel fibers, showed flexural failure behavior without shear failure. The aspect ratio of steel fiber had a great influence on the behavior of SIFCON beams without tensile steel, however the effect on the behavior of SIFCON beams was negligible. In addition, the flexural strength equation for SIFCON was proposed in the study. The mean and standard deviation of the ratios of the predicted value to the experimental value are 1.02 and 0.04, respectively. Therefore, the proposed flexural strength equation can be useful for the design and performance evaluation of SIFCON beam.

• Journal of the KSME
• /
• 제17권3호
• /
• pp.168-174
• /
• 1977

과학기술의 비약적인 발전에 따라서, 우주개발, 해양개발등을 실현시키는 단계에 이르렀고, 또한 이에 발맞추어 기계 및 구조물에 사용되는 각종부재의 경량화를 꾀하는 한편 사용장소가 매우 험악해지고 있다. 이와같은 사회적인 추세에 따라 재료가 보다 협악한 조건화에서 사용된다는 사 실은 최근에는 일만상식처럼되고 있다 따라서 험악한 장소에서 파괴가 발생한다면 최악이 경우는 인명을 위협하기도 한다. 이와같은 일반사항을 고려하여 본강좌(4) 에서는 특히 부식되기쉬운 장 소에서 부재가 사용되었을 때의 부식피로에 대하여, 극히 일반적인 사항을 간추려보기로 하겠다.