• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.2
• /
• pp.167-176
• /
• 2021

When producing recycled asphalt mix, it is important that the old binder of reclaimed asphalt pavement(RAP) should be well melted during blending in the mixer. The recycled asphalt mix is produced by instant mixing(IM) of all materials(RAP, virgin asphalt and new aggregates) all together in the mixer. However, in the same recycled mix, the binder around RAP aggregate was found to show higher oxidation level than the binder coated around the virgin aggregate because the old binder of RAP was not rejuvenated properly while instant mixing. The partially-rejuvenated RAP binder is assumed to be a high stiffness point in IM recycled mix. In this study, the stage mixing(SM) method was introduced; blending RAP and virgin asphalt for the first stage, and then mixing all together with hot new aggregates for the second stage. To compare the effect of the two mixing methods on moisture resistance of recycled mixes, a statistical t-test was performed between SM and IM using indirect tensile strength(ITS) and tensile strength ratio(TSR). Three conditioning methods were used; a 16-h freezing and then 24-h submerging, 48-h submerging, and 72-h submerging in 60℃ water. It was found that the TSR(=ITS_wet/ITS_dry) values of the mixes prepared by SM was clearly higher than the IM mixes, and coefficients of variation of SM mixes were lower than the IM mixes. It was also observed that the ITS_WET of SM was significantly different from the IM at α=0.05 level by statistical t-test. The ITS_WET of SM mix was reduced less than the IM mix in severer conditioned mixes. Therefore, it was concluded that the stage mixing method was an important blending technique for producing better-quality of recycled asphalt mixes, which would show higher moisture resistance than the recycled mixes produced by conventional instant mixing.

• Journal of Marine Bioscience and Biotechnology
• /
• v.2 no.3
• /
• pp.133-141
• /
• 2007

There are produced more than 600,000 tons of seaweeds every year along the coast of the Korea. Jeonnam province, south-west coast area, of Korea is producing 93% of total amounts of seaweeds. The laver, sea mustard, and tangleweed maintain stability in the output and has been exported as a simple product processing through drying or salting. It was evaluated the low value-added products and limited the expansion for the consumption of seaweeds. The seaweeds contains 40-60% carbohydrate and structurally different compared with land plant. The dietary fiber from seaweeds has been known the function of facilitating the bowl movement, excretion the heavy metal in the body, lowering the blood cholesterol level, anti-coagulant of blood, and anticancer. Especially, brown algae including sea mustard, seaweed fusiforme, and tangleweed contains alginic acid, laminarin, mannitol, fucoidan which are lowering the blood cholesterol level, lowering blood pressure, and fusion of blood clot. Agar-agar, carrageenan, and porphyran compound in red algae are known to antimutagenicity and anticoagulant function. In spite of potential of seaweed as a main bio-resource, there are lack of research to facilitate the consumption with its functional properties and consumers are unsatisfied with simple processing products. Also, the seaweed by-product dump into the sea and cause pollution of the seawater. Therefore, there are needed the scheme to promote the consumption of seaweeds. The development of value-added products, finding functional properties from seaweeds, development the functional feed for animal using seaweed by-products, and utilization of unused algae for food or other industrial uses will increase fisherman's income as well as serve as an aid for the people health due to its functional properties. Using by-product of seaweed and unexploited seaweed are needed to development of bio-degradable food packaging material and functional feed for animal.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.18 no.3
• /
• pp.145-155
• /
• 2002

The results of the present feasibility study are summarized as follows, 1. The three unit bridge of knitted material and UD fibre reinforcement has both the rigidity and the strength against a vertical occlusal load of 75N. 2. Stress concentration at the junctional area between the bridge and the abutments, i.e. between the pontic and the knitted caps was observed. In the case of the bridge with reinforcement straps, it was partly shown that the concentration problem could be improved by simply increasing the fillet size at the area. Further refining in the surface of the junctional area will be needed to ensure a further improvement in the stress distribution. This will require some trade off in the level of the stress and the available space. A parametric study will help to decide the appropriate size of the fillet. 3. Design refinement is a must to improve the stress distribution and realize the most favourable shape in terms of fabrication. The current straight bar with a constant cross section area can be redesigned to a tapered shape. The curve from the dental arch should also be placed on the pontic design. In accordance with design refinement, the resistance of the bridge frame to other load cases should be evaluated. 4. Although not included in the present feasibility study, it is estimated that bridges of the anterior teeth can be made strong enough with the knitted material without further reinforcement using unidirectional materials. In this regard, a feasibility study on design concepts and stress analysis for 3, 4, 5 unit bridge is suggested. 5. Two types of bridge were analysed in terms of fatigue. The safe life design concept, i.e. fatigue design concept, looks reasonable for the bridge where if cracks should form and propagate there is virtually nothing a dentist to do. The bridge must be designed so that no crack will be initiated during the life span. In the case of crowns, however, if constructed with composite resin with knitted materials, it might be possible to repair them, which in general is impossible for crowns of PFM or of metal. Therefore for composite resin crowns, a damage tolerance design concept can be applied and reasonably higher operational stresses can be allowed. In this case, of course, a periodic inspection program should be established in parallel. 6. Parts of future works in terms of structural viewpoint which need to be addressed are summarized as the following: 1) To develop processing technology to accommodate design concepts; 2) More realistic modelling of the bridge and analysis-geometry and loading condition. Thickness variation in the knitted material, taper in the pontic, design for anterior tooth bridge, the effect of combined loads, etc, will need to be included; 3) To develop appropriate design concepts and design goals for the fibre composite FPD aiming at taking the best advantage of knitted materials, including the damage tolerance design concept; 4) To develop testing method and perform test such as static ultimate load test, fatigue test, repair test, etc, as necessary.

• Food Science and Preservation
• /
• v.16 no.3
• /
• pp.405-411
• /
• 2009

The manufacturing process and quality properties of Lactococcus lactis-fermented yakchobugak (LFY) containing some colored agro-food products were investigated to develop a good organoleptic bugak from the leaf of the medicinal herb. The de-oiling rate of LFY by centrifugation was 37.6%, which was significantly different to the 3.5% value obtained after standing and the 8.9% value obtained with the beating method (p<0.05). Reducing power (RS) increased with addition of increasing levels of ethanol extracts from agro-food powders. The RS of green tea extract-supplemented LFY had the highest value of 0.97 at $500{\mu}g/mL$, and this was significantly different to values obtained using other extracts (p<0.05). At 83.84%, the DPPH (2,2-diphenyl-1-picrylhydrazyl) free-radical scavenging activity of green tea extract-supplemented LFY was the greatest of all samples tested, followed by LFY with woolgeom at 39.48%, LFY with black rice at 28.45%, and LFY with bokbunja at 22.24% all ethanol extracts were added at $50{\mu}g/mL$ (p<0.05). Acid values of green tea and bokbunja LFYs stored in transparent PE bags at $60^{\circ}C$ for 7 days were 1.82% and 2.03%, respectively. Textural hardness values of LFYs were less than 250.62, except for LFYs with black rice and woolgeom, but these values increased $2{\sim}3$-fold after lactic acid fermentation. Carbohydrate and protein content of LFYs were in the ranges $58.95{\sim}64.63%$ and $7.50{\sim}8.68%$, respectively. Lipid and calorie contents of woolgeom LFY had the lowest values of 22.02% and 490 Kcal, respectively.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.1
• /
• pp.29-37
• /
• 1999

In this study, we have prepared PLT thin films having various La concentrations by using sol-gel method and studied on the effect of La concentration on the electrical properties of PLT thin films. As the La concentration increases from 5mol% to 28mol%, the dielectric constant at 10kHz increases from 428 to 761, while the loss tangent decreases from 0.063 to 0.024. Also, the leakage current density at 150kV/cm has a tendency to decrease from 6.96${\mu}A/cm^2$ to 0.79${\mu}A/cm^2$. In the result of hysteresis loops of PLT thin films, the remanent polariation and the coercive field decrease from 9.55${\mu}C/cm^2$ to 1.10${\mu}C/cm^2$ and from 46.4kV/cm to 13.7kV/cm, respectively. With the result of the fatigue test on the PLT thin films, we have found that the fatigue properties are improved remarkably as the La concentration increases from 5 mol% to 28mol%. In particular, the PLT28) has paraelectric phase and its charge storage clensity and leakage current density at 5V are 134fC/${\mu}cm^2$ and 1.01${\mu}A/cm^2$, respectively. The remanent polarization and coercive field of the PLT(10) film are 6.96${\mu}C/cm^2$ and 40.2kV/cm, respectively. After applying of $10^9$ square pulses with ${\pm}5V$, the remanent polarilzation of the PLT(10) film decreases about 20% from the initial state. In the results, we conclude that the 10mol% and the 28mol% La doped PLT thin films are very suitable for the capacitor dielectrics of new generation of DRAM and NVFRAM respecitively.

• Journal of the Korea Concrete Institute
• /
• v.21 no.1
• /
• pp.93-103
• /
• 2009

The concept of the effective moment of inertia has been generally used for the deflection estimation of reinforced concrete flexural members. The KCI design code adopted Branson's equation for simple calculation of deflection, in which a representative value of the effective moment of inertia is used for the whole length of a member. However, the code equation for the effective moment of inertia was formulated based on the results of beam tests subjected to uniformly distributed loads, which may not effectively account for those of members under different loading conditions. Therefore, this study aimed to verify the influences of moment shapes resulting from different loading patterns by experiments. Six beams were fabricated and tested in this study, where primary variables were concrete compressive strengths and loading distances from supports, and test results were compared to the code equation and other existing approaches. A method utilizing variational analysis for the deflection estimation has been also proposed, which accounts for the influences of moment shapes to the effective moment of inertia. The test results indicated that the effective moment of inertia was somewhat influenced by the moment shape, and that this influence of moment shape to the effective moment of inertia was not captured by the code equation. Compared to the code equation, the proposed method had smaller variation in the ratios of the test results to the estimated values of beam deflections. Therefore, the proposed method is considered to be a good approach to take into account the influence of moment shape for the estimation of beam deflection, however, the differences between test results and estimated deflections show that more researches are still required to improve its accuracy by modifying the shape function of deflection.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.37 no.8
• /
• pp.1030-1036
• /
• 2008

In Korea, many types of traditional grape wine have existed starting from seven hundred years ago and horse-blossom-like-grape (mayu-podo) was mainly cultivated. Korean traditional wine (KTW) was manufactured by a unique method in which grape juice-added porridge made from glutinous rice was fermented by nuruk as a starter for brewing. Unfortunately, KTW making was discontinued in 20th century; thus, restoration of Korean wine culture is needed. KTWs were prepared by four traditional methods, and their qualities were compared to commercial wine made by sugaring grape juice. Ethyl alcohol contents, total acidity, pH and amino acid of the four KTWs were $9.2{\sim}11.2%$, $0.93{\sim}1.20\;mg$/100 mL, $3.02{\sim}3.48$ and $0.80{\sim}0.88\;mg$/100 mL respectively. The KTWs showed higher values in total acidity and amino acid than those of commercial grape wine. KTWs were rich in maltose, acetic acid and lactic acid. L, a and b value in Hunter's color value ranged $3.59{\sim}3.69$, $20.63{\sim}38.06$, and $1.20{\sim}1.56$, respectively. Sensory quality properties in color, flavor, taste and overall of KTWs were not different from commercial dry wine. Contents of total phenolic compounds and free radical scavenging activity using DPPH of KTWs were $599.6{\sim}652.2\;mg$/100 mL and $50.59{\sim}56.75%$, respectively.

• Asia-Pacific Journal of Business Venturing and Entrepreneurship
• /
• v.7 no.4
• /
• pp.101-112
• /
• 2012

Business consulting which aims at advising overall management, comparative advantage in competitive environment, administration and so forth is deemed to be significant so that a credit union may flexibly respond to rapid and complicated financial environment. Accordingly, business consulting has been initiated and implemented in credit union since 2002, which seemingly leads to positive outcome to enhance its competitiveness. However, very few research exists which analyze the credit union's competitiveness and business performance after the business consulting. Thus, the research intends to verify how consulting influences on management performance by its various factors. With the above studies in mind, hypothesis is formed that the characteristics of a consulting comsumer and the characteristics of supplier will give a meaningful impact on management performance. The test shows the result as followings: Firstly, a primary credit union's trust and NACUFOK's expertise demonstrate that they are closely relevant to financial and non financial management performance. Secondly, support and willingness to apply states that they influences on non financial performance, while no direct impact is found to financial performance. Thirdly, NACUFOK's capability is rarely interrelated to financial and non financial performance. The present study implies that the credit union as a consulting beneficiary should participate in the consulting, accept the result, and make effort to solve the management problems. In addition, NACUFOK as a consulting supplier should initiate the organization in exclusive charge, perform the professional group, and foster the professional consultant for the development of consulting method, the improvement of consulting process, and the specialization of consultant including the enhancement of core competencies. When these perspectives are sufficient, it will be connected to the management outcomes, further, it will be boosted up the competitiveness of the Credit Union. Hopefully the present study helps to motivate the consulting of primary credit union, boost up the effectiveness of consulting, further, providing the perspective on consulting the credit union. And these may result in the indication of consulting development direction and the competitiveness of Credit Union.

• Journal of the Microelectronics and Packaging Society
• /
• v.23 no.4
• /
• pp.113-117
• /
• 2016

Recently, hydrogen is regarded as important energy in the future, because it is clean and renewable. The photoelectrochemical (PEC) system, which produce hydrogen using water splitting by solar energy, is one of the most promising energy systems because it has abundant energy sources and good theoretical efficiency. GaN has recently been regarded as suitable photoelectrode that could be used to split water to generate hydrogen without extra bias because its band edge position include water redox potential ($V_{redox}=1.23$ vs. SHE). GaN also shows considerable corrosion resistance in aqueous solutions and it is possible to control its properties, such as structure, band gap, and catalyst characteristics, in order to improve solar energy conversion efficiency. But, even if the band edge position of GaN make PEC reaction facilitate without bias, the overpotential of oxygen evolution reaction could reduce the efficiency of system. One of the ways to decrease overpotential is introduction of co-catalyst on photoelectrode. In this paper, we will investigate the effect of manganese dioxide ($MnO_2$) as a co-catalyst. $MnO_2$ particles were dispersed on GaN photoelectrode by spincoater and analyzed properties of the PEC system using potentiostat (PARSTAT4000). After coating $MnO_2$, the flat-band potential ($V_{fb}$) and the onset voltage ($V_{onset}$) were moved negatively by 0.195 V and 0.116 V, respectively. The photocurrent density increased on $MnO_2$ coated sample and time dependence was also improved. These results showed $MnO_2$ has an effect as a co-catalyst and it would enhance the efficiency of overall PEC system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.23 no.8
• /
• pp.759-769
• /
• 2013

Electronic equipment has been applied to virtually every area associated with commercial, industrial, and military applications. Specifically, electronics have been incorporated into avionics components installed in aircraft. This equipment is exposed to dynamic loads such as vibration, shock, and acceleration. Especially, avionics components installed in a helicopter are subjected to simultaneous sine and random base excitations. These are denoted as sine on random vibrations according to MIL-STD-810F, Method 514.5. In the past, isolators have been applied to avionics components to reduce vibration and shock. However, an isolator applied to an avionics component installed in a helicopter can amplify the vibration magnitude, and damage the chassis, circuit card assembly, and the isolator itself via resonance at low-frequency sinusoidal vibrations. The objective of this study is to investigate the dynamic characteristics of an avionics component installed in a helicopter and the structural dynamic modification of its tray plate without an isolator using both a finite element analysis and experiments. The structure is optimized by dynamic loads that are selected by comparing the vibration, shock, and acceleration loads using vibration and shock response spectra. A finite element model(FEM) was constructed using a simplified geometry and valid element types that reflect the dynamic characteristics. The FEM was verified by an experimental modal analysis. Design parameters were extracted and selected to modify the structural dynamics using topology optimization, and design of experiments(DOE). A prototype of a modified model was constructed and its feasibility was evaluated using an FEM and a performance test.