• Land and Housing Review
• /
• v.1 no.1
• /
• pp.43-50
• /
• 2010

In this study, the influences of steel dampers on the behavior of RC frames were investigated using the experimental approach to suggest the installation methods of steel dampers using K-barces. The performances of RC frames with dampers can be evaluated by superposition the load-displacement curves of RC frames and steel dampers with regard to the influences of K-braces. Three specimens are tested to investigate the cyclic behavior of RC frames with dampers. The performances of RC frames with dampers with respect to strength, rigidity, and hysteretic performance are examined. It was found that test results demonstrates the effect of seismic retrofit on RC frames with steel dampers(D-RCF-KBSF, D-RCF-KBSP) compared with RC frames(N-RCF). An approximate design curves may not be good agreement with those of the tests, it is conservative enough so that you can design of RC frames with steel damper with regard to the influences of K-braces.

• Geotechnical Engineering
• /
• v.7 no.4
• /
• pp.15-24
• /
• 1991

This paper reports the application study of the concrete bedding reinforcement under a buried conduit with flexible joints subjected to differential settlement via a finite elemen modeling. The reinforcement of concrete bedding helps to minimize the differential settlement between the adjoining conduit segments. Three different field conditions have been considered. The settlement pattern and deformation slope have been evaluated for each boundary condition. The analysis results are compared for both non-reinforced and reinforced cases to measure the effectiveness of concrete bedding reinforcement for restraining deformation of a conduit with flexible joints.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1993.04a
• /
• pp.80-84
• /
• 1993

공기베어링은 기체으 압축성에 의한 평균화 효과로 운전정밀도가 우수하고 기체의 낮은 점도에 의한 효과로 마찰력과 열발생량이 매우 적으며, 사용가능 온도구간이 저온에서 고온까지 넓고 프로세스 계통내의 기체를 윤활제로 사용할 수 있기 때문에 그 경우 불순물에 의한 오염이 문제되지 않는 장점등이 있다. 이와 같은 특성과 더불어 공기베어링은 지지 물체를 완전히 부상시켜 운전하므로써 마찰$\cdot$마모와 온도변화에 다른 열변형이 문제되지 않는다. 이러한 장점으로 인해서 공기베어링은 현재 정밀기기의 미끄럼면, 각종 측정장치의 테이블지지 기구로 많이 사용되고 있다. 반면 공기베어링의 단점으로는 기체의 낮은 점성계수로 인해서 부하능력이 적고 강성, 감쇄계수 또한 적다. 그리고 기체의 압축성으로 인해 뉴메틱 헤머라는 불안정 현상이 생기기도 한다. 본 연구에서는 스퀴즈 효과를 이용한 능동 공기베어링을 설계, 제작하여 실험하였다. 본 연구의 목적은 강성과 감쇄 계수가 작은 공기 베어링의 단점을 보완하기 위해 드러스트베어링을 대상으로 능동베어링을 설계, 제작하여 그 특성을 연구하고 기초 설계자료를 축적하는데 있다.

• Journal of the Korea Concrete Institute
• /
• v.17 no.6 s.90
• /
• pp.1033-1042
• /
• 2005

Until recently tensile stresses in concrete have not been considered, since it does not affect the ultimate strength of reinforced concrete flexural members significantly However, to verify the load-deflection relationship, the effect of tensile stresses between reinforcing bars and concrete, so-called tension stiffening effect must be taken into account. Main parameters of the tension stiffening behavior are known as concrete strength, and bond between concrete and reinforcing bars. In this study total twenty specimens subjected to bending were tested with different concrete strength, coverage, and de-bonding length of longitudinal bars. The effects of these parameters on the flexural rigidity, crack initiation and propagation were carefully checked and analyzed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.17 no.1
• /
• pp.85-93
• /
• 2013

In order to make a more reasonable evaluation on the stiffness of the high-strength mortar-filled sleeve bar splices under cyclic loading, we investigated and analyzed the existing experiment data of 106 full-sized reinforcing bar splices with test variables such as compressive strength of mortar, development length of reinforcement and sleeve type, etc. The following were found: 1) If mortar and the reinforcement development length with $f_{g^*}$(L/d) of more than 340 is used, the cast iron sleeve bar splices for SD350 and SD400 will have the stiffness of higher than A class of the AIJ code. 2) If mortar and the reinforcement development length with $f_{g^*}$(L/d) of more than 400 is used, the cast iron sleeve splices and pipe sleeve splices for SD500 will have the stiffness of higher than A class of the AIJ code.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2004.05a
• /
• pp.216-217
• /
• 2004

• 한국과학교육학회:학술대회논문집
• /
• 2008.01a
• /
• pp.129.3-129.3
• /
• 2008

• Geotechnical Engineering
• /
• v.6 no.4
• /
• pp.43-52
• /
• 1990

To investigate the effects of soil properties of the soft zone around a pile subjected 1,o the horizontal harmonic vibration, the parametric study is perfomed. The determination of the soil reaction or stiffness of the Winkler springs representing the soil around a pile is performed by dividing the soil profile into a number of homogeneous obtained from this study are as follows : 1) The real and imaginary parts of the stiffness show clear variations for the different shear modulus ratios, poisson's ratios, and distance retios to outer boundary as the dimensionless frequency increases. The differences are more pronounced for the imaginary part of the stiffness. 2) The stiffness of soil shows clear decrease. The real parts of the stiffness show larger as the frequency increases. On the other hand, the imaginary parts of the stiffness show smaller.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.9
• /
• pp.39-49
• /
• 2007

The load deformation behavior of the cap-pile-soil system is investigated, based on numerical analysis. Special attention is given to consideration of pile cap flexibility. Rigid pile cap analysis and flexible cap analysis were conducted for comparison. A numerical method that takes into account the coupling between the rigidities of the piles, the cap, and the column has been introduced to analyze the response of pile group supported columns. The prediction of the lateral loads and bending moments in the pile cap is much more conservative for a flexible cap than for a rigid cap.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.1
• /
• pp.714-721
• /
• 2018

In this study, we investigate a design technology intended to radically increase the buckling strength of vertically curved panels. Recent studies proposed a buckling strength formula which properly reflects the effect on the local plate buckling strength of flat plates when they are stiffened by closed section ribs. Herein, we attempted to quantitatively evaluate this effect on curved panels and to reveal the correlations with the design parameters. The commercial finite element software, ABAQUS, was used to build a three dimensional numerical model and numerical parametric studies were conducted to evaluate the variation of the buckling strength. In the case of flat panels, the local buckling strength of stiffened curved panels increases proportionally with increasing rotational stiffness of the closed-section ribs. After attaining a limiting value, an obvious tendency was found that the local buckling strength of the stiffened curved panel would converge towards a fixed value when the panels are supported along both sides. The parametric studies performed using the influential design parameters confirmed that the estimated partially-restrained curved panel strength is well correlated with the proposed formula.