• Journal of the Korean Society for Railway
• /
• v.20 no.3
• /
• pp.311-319
• /
• 2017

The primary suspension system of a railway vehicle restrains the wheelset and the bogie, which greatly affects the dynamic characteristics of the vehicle depending on the stiffness in each direction. In order to improve the dynamic characteristics, different stiffness in each direction is required. However, designing different stiffness in each direction is difficult in the case of a general suspension device. To address this, in this paper, an optimization technique is applied to design different stiffness in each direction by using a conical rubber spring. The optimization is performed by using target and analysis RMS values. Lastly, the final model is proposed by complementing the shape of the weak part of the model. An actual model is developed and the reliability of the optimization model is proved on the basis of a deviation average of about 7.7% compared to the target stiffness through a static load test. In addition, the stiffness value is applied to a multibody dynamics model to analyze the stability and curve performance. The critical speed of the improved model was 190km/h, which was faster than the maximum speed of 110km/h. In addition, the steering performance is improved by 34% compared with the conventional model.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2004.05a
• /
• pp.216-217
• /
• 2004

• Journal of the Institute of Convergence Signal Processing
• /
• v.23 no.1
• /
• pp.1-7
• /
• 2022

As a power transmission element, the timing belt is a toothed transmission belt that takes advantages of V-belts and gears. It has characteristics of non-slip and low noise. It is used as a power transmission device when transmitting power from a rotating shaft or linear motion in a mechanism. Rotation can be accurately transmitted through a belt pulley with grooves like a gear and a timing belt with grooves to precisely match with the belt pulley. In particular, in the mechanism in which the timing belt is used for the output shaft, the dynamic characteristics including the rigidity of the timing belt determine the transmission characteristics of the system, so its importance increases. In this paper, a stiffness reinforced belt that can be applied to a timing belt with a limited range of motion to increase its stiffness is proposed. To study the dynamic characteristics of the stiffness reinforced belt, the equation of motion for the stiffness reinforced belt was established, and a simulation model for the stiffness reinforced belt was created and analyzed. In order to confirm the analysis results of the motion equation and simulation model, a 1-axis rotation experimental equipment using a stiffness reinforcing belt was developed and the experiment was conducted. Through motion equations, simulation models, and experiment results, it was confirmed that the stiffness and dynamic characteristics of the timing belt could be improved by applying the proposed stiffness reinforcement belt.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.7
• /
• pp.688-694
• /
• 2008

A rotordynamic analysis is performed for a high thrust class liquid rocket engine turbopump considering the dynamic characteristics of ball bearings and pump noncontact seals. Complex eigenvalue problems are solved to predict the rotating natural frequencies and damping ratios as a function of rotating speeds. Synchronous rotor mass unbalance response and time transient response analyses are also performed to figure out the rotor critical speed and the onset speed of instability. From the numerical analysis, it is found that the rear bearing stiffness is most important parameter for the critical speed and instability because the 1st mode is turbine side shaft bending mode. The pump seal effect on the critical speed is enlarged as the rear bearing stiffness decreases and the front bearing stiffness increases.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05a
• /
• pp.989-994
• /
• 1995

본 연구의 목적은 국내에서 개발중인 액체금속로의 면진설계를 위하여 면진층과 원자로용기 사이에 있는 내진벽의 강성이 면진시스템의 지진응답에 미치는 영향을 분석하는 것이다. 이를 위하여 내진벽강성을 고려한 모우드해석을 수행하여 내진벽의 강성변화에 따른 동특성해석을 수행하였으며 면진 및 비면진시스템의 경우에 대하여 지진해석을 수행하였다. 면진 및 비면진시스템에 대한 지진해석결과에서 비면진시스템의 경우에 내진벽강성은 지진응답에 영향을 주지만 면진시스템의 경우에는 그 영향이 매우 작은 것으로 나타났다.

• Journal of the Korean GEO-environmental Society
• /
• v.19 no.2
• /
• pp.37-44
• /
• 2018

Ballasted track has been widely used due to its flexibility. However, the plastic deformation of ballasted track causes the evolution of track geometrical errors, and hence it requires continuous maintenance; increase in number of trains, weight, and speed expedites maintenance frequency and cost as well. Ballast stiffness is well-known as an indicator of design and maintenance. In this regard, this paper aims to suggest the method to measure ballast track stiffness using light-weight deflectometer (LWD) and thus verify its applicability as a maintenance measure. Preliminary field tests determined simple field testing protocol to measure track stiffness. The apparent ballast stiffness by LWD shows good corelation with TQI (Track Quality Index) and maintenance length. That is, as average of apparent stiffness increase, TQI and tamping length decrease exponentially. Therefore, apparent stiffness can be used as an index for ballast condition assessment.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.12
• /
• pp.1635-1642
• /
• 2012

The identification of the dynamic properties of structural joints is important for predicting the dynamic behavior of assembled systems. However, the identification of the properties using analytical or experimental approaches is extremely difficult or even impossible. Several studies have proposed hybrid or synthesis methods that simultaneously used analytical and experimental approaches to identify the dynamic properties of a joint. However, among the many types of joints, only the bolt joint was treated as a practical example in these studies. In this study, for a simple assembly system comprising two plates and one hinge joint, a simple methodology involving the use of the static-based subpart analysis method to identify the dynamic properties is proposed. Finally, the proposed method is applied to a glove box in a passenger vehicle that includes hinge joints.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.6
• /
• pp.463-470
• /
• 2013

In this paper, 2D simple analyses were performed in order to predict the large torsional oscillations in a suspension bridge based on Makenna and Tuama model(2001). The existing model(Makenna and Tuama, 2001) has shown unrealistic results as the wind speed increases and frequency decreases. Furthermore, resonance could not be simulated by the existing model. Therefore, in this study, new model was proposed with a consideration of the torsional resistance. The vertical and rotational behaviors of the deck in the suspension bridge were analyzed. Analysis results showed that at first vertical oscillations were observed and it was gradually transformed to the rotation oscillations. With the consideration of the torsional resistance, it was shown that vertical behavior were stabilized as time passed. However, the rotational behavior was not stabilized and was kept until the end of analysis. Beat periods decreased while the wind speed increased. The resonance of the rotational mode was dependent to the rotational resistance. Obtained results could be applied for the design of the suspension bridge under the wind load.

• Computational Structural Engineering
• /
• v.8 no.2
• /
• pp.103-113
• /
• 1995

Since the mechanical properties of the rubber connectors used in the vehicle structures are sensitive on the dynamic characteristics of the system, they must be exactly evaluated. In this paper, both finite deformation theory and Hookean model are considered to calculate the stiffness coefficients of rubber connectors. An expert system is developed by using finite element method. When the equivalent stiffness coefficients on the same kinds of isolators used in actual vehicles were emperically examined, the results were largely dispersed due to the lack of the quality control on the material properties. To compensate the errors caused by the mathematical modeling and the mechanical properties, a practical method which identifies the shear and bulk moduli of rubber with the experimented overall force-deformation curves is suggested and applied to the engine isolators of vehicle.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.1
• /
• pp.16-22
• /
• 1994

수중 예인시스템의 동적 거동 해석을 위한 3차원 비선형 수학모델이 제시되었다. 수중 예인체는 세장보로 이상화되었으며, 보요소의 굽임강성 및 비틈강성의 영향이 수학모델에 포함되었다. 축류가 지배적인 비정상 상대유동장내의 세장예인체의 횡방향 운동에 따른 유체동역학적 반력과 기진력에 관한 비선형 3차원 수학 정식화가 수행되었다.