• Journal of the Korean GEO-environmental Society
• /
• v.15 no.2
• /
• pp.53-58
• /
• 2014

The uniaxial compressive strength and Young's modulus of intact rocks are the most important analytical parameters for design of rock mass structures. But the preparation of the samples for uniaxial compressive test is a hard and time consuming task. By using ultrasonic test, engineers can predict the analytical parameters that is the uniaxial compressive strength and Young's modulus. The uniaxial compressive test and ultrasonic test were carried out 115 samples of igneous rocks, 74 samples of metamorphic rocks and 55 samples of sedimentary rocks and, after regression analysis of the test results, best fit equations for predicting the uniaxial compressive strength and Young's modulus are proposed. In order to obtain a better correlations coefficient between uniaxial compressive strength and P-wave velocity, the P-wave velocity were multiplied by density values. The proposed equations for predicting uniaxial compressive strength and Young's modulus using ultrasonic test provide reliable results.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.4
• /
• pp.299-306
• /
• 2023

Environmental pollution problems are occurring due to the negative treatment of basalt waste in Jeju Island. This study identifies the characteristics of permeable block with basalt with physical and chemical adsorption mechanisms and examines their applicability and functionality as building materials. This experiment is basic data for evaluating the functionality of the permeable block by analyzing flexural strength, compressive strength, permeability coefficient, carbon dioxide, and fine dust adsorption rate by producing a permeable block using a basalt waste rock. As the basalt waste stone replacement rate increased, the flexural strength and compressive strength tended to decrease, and as the replacement rate increased, the water permeability coefficient, absorption rate, carbon dioxide, and fine dust adsorption rate tended to increase. Therefore, it is judged that the permeable block using the basalt waste rock is superior to the existing permeable block.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.12
• /
• pp.75-80
• /
• 2017

Permeable block pavement systems are widely used to relieve the flood and enhance water circulation. However, domestic design method has not yet been established well. Although AASHTO 93 flexible pavement design method is applied as a structural design method outside the country, there is a lack of information on layer coefficient of the permeable pavement materials, which makes it difficult to apply the design to various materials. Therefore, in this study, a method of calculating the layer coefficient of permeable block pavement materials by plate load test was presented and the layer coefficient of a permeable block pavement in a testbed was evaluated. Overall, calculated layer coefficient of open graded aggregate and permeable block pavement surface layer were similar to those of the conventional values. The presented method may be used to evaluate layer coefficients of permeable block pavements for design.

• Journal of the Korea Concrete Institute
• /
• v.18 no.6 s.96
• /
• pp.811-817
• /
• 2006

The primary purpose of this study is to estimate the guaranteed strength and construction quality of the combined high flowing concrete which is used in the slurry wall of underground LNG storage tank. The required compressive strength of this type of concrete become generally known as a non economical value because it is applied the high addition factor for variation coefficients and low reduction factor under water concrete. Therefore, after estimation of the construction quality and guaranteed strength in actual site work, this study is to propose a suitable equation to calculate the required compressive strength in order to improve its difference. Application results in actual site work are shown as followings. The optimum nix design proportion is selected that has water-cement ratio 51%, sand-aggregate ratio 48.8%, and replacement ratio 42.6% of lime stone powder by cement weight. Test results of slump flow as construction quality give average 616~634mm. 500mm flowing time and air content are satisfied with specifications in the rage of 6.3 seconds and 4.0% respectively. Results of strength test by standard curing mold show that average compressive strength is 49.9MPa, standard deviation and variation coefficients are low as 1.66MPa and 3.36%. Also test results by cored cylinder show that average compressive strength is 66.4MPa, standard deviation and variation coefficients are low as 3.64MPa and 5.48%. The guaranteed strength ratio between standard curing mold and cored cylinder show 1.23 and 1.32 in the flanks. It is shown that applied addition factor for variation coefficients and reduction factor under water concrete to calculate the required compressive strength is proved very conservative. Therefore, based on these results, it is proposed new equation having variation coefficients 7%, addition factor 1.13 and reduction factor 0.98 under water connote.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.461-464
• /
• 2000

A branched crack in a semi-infinite plate under tension and bending moment is considered. Intensity factors of the stress and moment for the branched crack are evaluated. The stress intensity factors are obtained by using the finite element method and the J-based mutual integral. The moment intensity factors are calculated by extrapolating the values of the moment near the crack tip. Approximate expressions are also obtained as functions of the branched crack length and branching angle.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1989.06b
• /
• pp.29-34
• /
• 1989

고분자 복합재료들은 오늘날 광범위하게 마찰 부위들에 응용되고 있다. 다양한 첨가제와 보강재들이 고분자 물질들에 넣어져 강도와 마모 특성들을 향상 시키고 있다. 예를 들어, 다양한 복합재료들로서 현재 입수 가능한 것에 베어링 재료들이 있으며 이에 포함되는 것이 자체 윤활 보강 플라스틱 들이며 이들에는 고체 윤활제, 즉, 테플톤, $MoS_2$, 혹은 흑연가루들이 첨가된다. 실험적 그리고 이론적인 연구들이 여러 조건들에서의 섬유 보강 복합 재료들의 마모 거동에 대하여 보고되었다(예를 들어, 미끄럼 마모, 연마 마모, 입자 충격 마모, 비빔 마모). Tsukizoe와 Ohmae의 보고에 의하면 탄성계수 탄소섬유 복합재료는 가장 적은 마모가 횡단 방향(Transverse)에서 있고, 고 강도 탄소 섬유 복합재료는 길이 방향(Longitudinal)에서 있다. 가장 많은 마모는, 고 탄성계수 복합재료는 길이 방향에서, 고 강도 섬유 복합재료는 횡단 방향에서 잇다. 그들이 또한 발표한 것은 양쪽의 고 탄성계수와 고 강도 섬유 복합재료들의 수직방향(Norma)에서 눌러 불음(Seizure)가 일어났다고 한다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.10a
• /
• pp.240-240
• /
• 2003

V-노치 균열에서 열하중이 작용하는 경우는 비제차형 경계조건의 문제가 되고, 이 조건에 대한 방정식의 일반해를 구하기 위해서 재차형 연립방정식에 대한 일반해(Homogeneous solution)와 비제차형 연립방정식에 대한 특수해(Particular solution)의 두 가지 해를 구할 수 있다. 이들 해는 V-노치 균열에 대한 고유치가 되고 이 고유치가 중복근을 가지게 되는 경우에는 로그항(1n[r])이 나타나게 되고 이 항에 의해서 응력을 무한대로 발산시키므로 이를 대수응력특이성이라 한다. 열하중이 작용할 때 대수응력특이성을 나타내는 로그항의 계수가 영(0)이 되어 대수응력특이성이 사라지게 되므로 V-노치 선단에서의 응력특이성은 고유치와 그에 대한 고유벡터에 의해 결정된다. 본 논문에서는 비정상상태 열하중이 가해지는 등방성 이종재료 내의 V-노치 균열문제에서 패기 각도와 이종재료의 기계적 성질에 의해 결정되는 응력특이성지수를 구하고 이에 대한 응력강도계수를 유한요소해석 프로그램인 ANSYS와 상반일 경로 적분법(RWCIM)을 이용하여 구하였다.

• Journal of Ocean Engineering and Technology
• /
• v.6 no.2
• /
• pp.71-75
• /
• 1992

기구나 구조물의 피로수명은 노치에서의 피로균열 방생수명에 의하여 지배되기때문에 노치로 인한 피로강도감소계수 $K_f$는 피로설계상 대단히 중요한 인자이다. 노치 선단(Notch root)에서의 피로균열발생명수 N$_c$를 기준으로하면 탄성응력집중계수 $K_t$가 10 정도까지 $K_f$와 $K_t$간에는 거의 직선적인 관계가 있음이 이다- 고에 의하여 명석해졌으나 이는 인장,압축의 축력이 작용하였을 때이며 따라서 기구나 구조부재는 축력외에도 굽힘 피로 하중이 작용하였을때도 많으므로 본 연구에서는 굽힘 피로 하중을 받았을때도 있다. -고의 결론이 적용되는지는 검시코져 본 연구를 실시하였다.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.309-314
• /
• 2007

Recently, the LRFD and the PSF based on structural reliability assessment have been applied to NPP designs in behalf of the conventional deterministic design methods. In the risk-informed structural integrity, it is especially possible to optimize design procedures considering cost, manufacturing and maintenance because the structural reliability concepts have confirmed the reliability for which a designer aims. Generally, in order to evaluate the PSF, the LRFD which is the design concept for evaluating safety factors respectively on the limit state function including load and resistance. This study certifies the concept and its applications of the PSF using the LRFD based on the structural reliability engineering.

• Journal of the Korean Society of Industry Convergence
• /
• v.3 no.1
• /
• pp.53-59
• /
• 2000

단섬유 보강 복합재료의 종횡비(aspect ratio)를 변화시키며 기계적 특성(탄성계수, 인장강도)을 평가하였다. 2차원 다중 파이버(multi-fiber) 모델을 이용하여 엇갈린(staggered) 배열과 규칙적(aligned) 배열에 대해 유한요소 해석을 하였다. 단섬유 복합재료의 유효탄성계수 및 인장강도는 섬유와 기지의 탄성계수비, 섬유 배열상태, 그리고 단섬유 종횡비의 함수로 표현되었으며, 해석결과의 탄성계수와 인장강도는 이론 모델의 결과와 사출 성형된 PEEK 복합재료 시험편의 결과와 비교하였다. 시험결과는 낮은 종횡비에서 이론 모델 결과와 일치함을 보였다. 단섬유 보강 복합재료의 배열 및 종횡비 변화에 따른 섬유보강 효과에 따른 계면응력 상태는 기계적 특성 결정에 중요한 영향을 보였다.