• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.29 no.2
• /
• pp.182-186
• /
• 2007

A cyst is a pathologic lesion characterized by a cavity filled with fluid, celluar products, air, or a combination of these. Dentigerous cysts were formed around the crown of unerupted teeth. The reduced enamel epithelium persists around the crown after it has formed. Proliferation of the epithelium in a fluid-filled sac may be induced by osmotic pressure. In the first decade the most frequent location is the premolar site. In each subsequent decade the largest number of cysts are in the mandibular third molar site, with the second most frequent site being the maxillary canine. The treatment of odontogenic cyst can be mostly classified into three types of cyst enucleation, marsupialization and decompression. We should consider age of patient, anatomic structure, location and size for choosing a treatment method. Advantage of cyst enucleation is fast healing, but a injury of a surrounding structure is highly. Marsupialization is conservative treatment that can reduce the damage of a adjacent structure, but it is only limited at superficial lesion. Decompression also is conservative treatment, but it has the difficulty of the oral hygiene and the troublesome of the lavage. We present the possibility that reduces the defect of decompression and cures the lesion efficiently. We report a male patient with the dentigerous cyst developed at left mandibular third molar in this study. We used the decompression for a treatment and created special appliance to treat the lesion efficiently. We report a case of the cyst treatment that is association with efficiency of decompression appliance.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.3 no.2
• /
• pp.47-57
• /
• 1995

The purpose of this study was to investigate the effect of mechanical mixing intensity on composting. The major parameters investigated were the mixing intensity and initial moisture content. Laboratory scale composting reactors with mixing equipment were used in this study. Wastes used for the study were raw nightsoil sludge, nightsoil sludge after vacuum evaporation treatment and pig manure. When moisture contents were 60% and 63%, amount of organic material degraded in the continuous mixing reactors was higher than that in the intermittent mixing reactors. Compost produced from reactors with continuous mixing had better texture than that obtained from reactors with intermittent mixing. When moisture content was 68%, organic waste was kneaded rather than mixed in the continuous mixing reactors. Amount of organic material degraded in the continuous mixing reactors also was lower than that in the intermittent mixing reactors.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.95-103
• /
• 1999

Low pressure combustion characteristics of the composite solid propellants were studied in terms of the propellant burning rate, ignition processes, and the structure of the extinguished surfaces. Optical Vacuum Strand Burner(OVSB) system was designed and configured for this purpose. Burning rates of the propellants were measured at subatmospheric pressure by developed test method in OVSB. The ignition and combustion phenomena of the studied propellants in the combustion chamber of OVSB were recorded and analyzed with the camera and VCR(30 frames/s). Burning surfaces of the propellants were extinguished by rapid depressurization method and analyzed with Scanning Electron Microscope(SEM).

• Clean Technology
• /
• v.13 no.4
• /
• pp.257-265
• /
• 2007

As a basic study for the development of pilot-scale distillation process of waste photoresist strippers from semiconductor industry, lab-scale experiments for the recovery of NMP (N-methy1-pyrrolidione) and BDG (Butyldiglycol) from waste photoresist strippers have been made using a spinning band vacuum distillation column. Purities of NMP and BDG obtained from the present experiments were higher than 99.5%. Furthermore, water content was less than 1000 ppm, color grade(APHA) less than 50, most metal contents except sodium less than 1 ppb. Those results indicate that NMP and BDG reclamed by distillation satisfy the their specifications required for the formulation of new photoresist strippers. Recovery rate of NMP and BDG was 96 and 53%, respectively, for type A, and 93 and 57%, respectively, for type B waste PR stripper solution.

• Applied Chemistry for Engineering
• /
• v.21 no.3
• /
• pp.295-300
• /
• 2010

A binary system of 1-propanol and bromochloromethane which exhibits an azeotropic point and a considerable nonideal phase behavior probably due to the large boiling point difference is not amenable in the actual chemical processes such as the distillation tower and absorber. Therefore, experimental data of phase behavior data of this mixture are indispensable in understanding the inherent thermodynamic characteristics for an efficient application of the system in the industrial processes. In this work, the isobaric vapor-liquid equilibrium of a binary mixture consisting of 1-propanol and bromochloromethane was measured by using a recirculating equilibrium cell at various pressures ranging from 30 to 70 kPa. The measured VLE data were correlated in a satisfactory manner by using the UNIQUAC and NRTL models along with the thermodynamic consistency test based on Gibbs/Duhem equation. In addition, the excess molar volume of the mixture was also measured by using a vibrating densitometer and correlated with a Redlich-Kister polynomial.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.37 no.2
• /
• pp.133-136
• /
• 2011

Cystic lesions on the jaws with expansion can invade the adjacent anatomical structure, infiltrate and expand the jaws, cause facial deformity, etc. There is great potential for pathologic fractures after cyst enucleation, and damage to the major structures like the nerve, artery. For these reasons, marsupialization and decompression are commonly used to reduce the cystic size. In 1947, Thomas first mentioned decompression that reduces the osmotic pressure in a cyst by making a hole in the cyst and insert a drain. In our cases, a large sized cystic lesion was treated with a specific device made from an orthodontic band and spinal needle. This device is easy and effective for applications and self irrigation.

• Clean Technology
• /
• v.17 no.4
• /
• pp.306-313
• /
• 2011

Flux or solder is used in soldering process for manufacturing electronic parts such as printed circuit boards (PCB). After soldering process, residual flux and solder paste on the parts should be removed since their residuals could cause performance degradation or failure of parts due to their corrosion and electric leakage. Ozone depletion substances such as 1,1,1- trichloroethane (TCE) and HCFC-141b have widely been using for removal of residual flux and solder paste after soldering process In manufacturing of electronic parts until now. In this study, non-aqueous cleaning agents without flash point were developed and applied to industrial field for replacement of cleaning agents with ozone depletion. In order to develop non-aqueous cleaning agents without ethers, esters, fluoride- type solvents. And their physical properties and cleaning abilities were evaluated, and they were applied to industrial fields for cleaning of flux and solder on the PCB. And vacuum distillation apparatus were operated to determine their operating conditions and recycling yields for recycling of used cleaning agents formulated in this study. As a result of physical properties measurement of our formulated cleaning agents, they were expected to have good wetting and penetrating power since their surface tensions were relatively low as 18.0~20.4 dyne/$cm^2$ and their wetting indices are relatively large. And some cleaning agents holding fluoride-type solvents as their components did not have any flash point and they seemed to be safe in their handling and storage. The cleaning experimental results showed that some cleaning agents were better in their cleaning of flux and solder paste than 1,1,1-TCE and HCFC-141b. And industrial application results of the formulated cleaning agents for cleaning PCB indicated that they can be applicable to industry due to their good cleaning capability in comparison with HCFC-141b. The recycling experiments of the used formulated cleaning agents through a vacuum distillation apparatus also showed that their 91.9~97.5% could be recycled with its proper operating conditions.

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1155-1160
• /
• 1999

The screening methodology modeling, dispersion modeling procedures for continuous and instantaneous releases of the gas phase flow from the storage tank and pressure relief valve were considered. This study was performed to develop the screening methodology for prediction and control of hazardous/toxic gas releases by estimating the 1-hr average maximum ground-level concentration of $Cl_2$ gas vs. downwind distance by incorporating source term model including the general/physical properties of released material and release mode of the $Cl_2$ storage tank of the chemical plant facilities, dispersion model, and meteorological/topographical data into the TSCREEN model. As the results of the study, it was found that dispersion modes of the dense gas were affected by the state of the released material, the released conditions, physical-chemical properties of released material, and the released modes (continuous and instantaneous releases), and especially largely affected by initial (depressurized) density of the released material and release emission rate as well as the wind velocity. Especially, this study was considered to release hazardous material as meteorological data. It was thought that this screening methodology can be useful as a preliminary guideline for application of the refined analysis model by developing the generic sliding scale methodology for various senarios selected.

• Korean Chemical Engineering Research
• /
• v.62 no.2
• /
• pp.163-172
• /
• 2024

In this study, two different scenarios for ammonia liquefaction in the green ammonia manufacturing process were proposed, and the economic-feasibility and environmental impact of each scenario were analyzed. The two liquefaction processes involved gas-liquid separation before cooling at high pressure (high pressure cooling process) or after decompression without the gas-liquid separation (low pressure cooling process). The high-pressure cooling process requires higher capital costs due to the required installation of separation units and heat exchangers, but it offers relatively lower total utility costs of 91.03 $/hr and a reduced duty of 2.81 Gcal/hr. In contrast, although the low-pressure cooling process is simpler and cost-effective, it may encounter operational instability due to rapid pressure drops in the system. Environmental impact assessment revealed that the high-pressure cooling process is more environmentally friendly than the low-pressure cooling process, with an emission factor of 0.83 tCO₂eq less than the low-pressure cooling process, calculated based on power usage. Consequently, the outcomes of this study provide relevant scenario and a database for green ammonia synthesis process adaptable to various process conditions.

• Food Industry
• /
• s.94
• /
• pp.37-40
• /
• 1988

1) 본 연구에서 시료로 선정한 충남 서산산 건강(dry ginger)은 수분이 $9.4\%$, 회분이 $8.7\%$ 그리고 alcohol에 의한 추출량이 약 $9\%$이다. 이는 선진국에 채택사용하고 있는 건강의 규격기준에 의하면 양호하다. 2) Non- flavor물질의 추출을 최소화하고 특히 증류과정에서 유효성분 손실을 최소화 할 수 있고, 엑기스내의 용매 잔류량이 인체에 유해하지 않고 추출효율을 높일 수 있는 용매는 ethyl alcohol이다. 3) 널리 사용하고 있는 관류추출(percolation)의 성능을 분석하고 이의 개선방안을제시하였다. - 추출효율을 높이기 위하여 건강(dry ginger)의 입자를 작게하면 압력강하가 증대되어순환되는 용액의 유속을 제어하기가 힘들다. - 입자가 작을 시에는 유체의 흐름이chan-nelling현상을 나타낸다. - 위와 같은 조건에서는 물질 전달속도가 느리므로 추출효율을 증대시킬 수가 없다. - 따라서 percolation추출에 사용되는 건강의 입자크기는 30mesh크기 이상이어야 운전조작이 용이하나 추출효율이 낮으므로, 추출시간 6시간에 회수된 생강엑기스양은 약 $2.5\%$이다. 4) percolation추출의 단점을 보완하기 위하여 기계적교반 추출을 선택하여 다음과 같은 개선점을 찾았다. - 교반형 추출에서는 고 - 액분리시 cake 저항에서 문제가 야기되지 않는 범위까지 건강의 입자를 작게할 수 있으므로 추출효율을 크게 향상시킬 수 있었다. 즉, 작게 분쇄된 건강(30mesh통과$90\%$)을 대상으로 추출시간 3시간에 $7\%$의 회수율로 증대시켰다. 최적 운전조건은 다음과 같다. 건강시료:1kg 시료크기:-30mesh$90\%$ 용매:ethyl alcohol 3$\iota$ 교반속도:900r.p.m 추출온도:상온($15\~25^{\circ}C$) 추출시간:3시간 일차 추출조건과 동일하게 하여 얻어진 엑기스의 수율이 $2\~2.5\%$이므로 총엑기스의 수율은 건강(dry ginger)무게기준으로 $8.5\~9.5\%$이었다. 5) 교반추출의 효율이 개선되었다 하더라도 추출물의 분리가 용이하여야만 공정의 이용이 가능하다. 그러므로 교반추출후 고 - 액분리를 위하여 정압여과 장치를 이용하여 여과시 cake의 평균 비저항을 얻었으며, 이의 값은 $4.31\times10^8cm\;/\;gr$으로서 여과에는 어려움이 없다는 것을 의미한다. 따라서 추출속도와 효율이 상대적으로 우수한 교반형 추출기의 가능성을 예시할 수 있음을 알 수 있었다. 6) 추출물을 농축과정에서 휘발성 oil의 손실을 최대로 줄이기 위해서는 단순증류를 하지 말고 분별증류를 수행하여야 하며, gingerol과 같은 중요성분의 열분해 반응을 억제하기 위해서는 열전달 효율을 증대시켜 증류조작을 원활히 수행하여야 하므로, still내의 농축물을 계속 교반시켜야 하며 감압상태에서 증류온도는 $40\~50^{\circ}C$로 유지시키는 것이 가장 바람직하다. 7) Ethyl alcohol로 추출된 엑기스내의 수분이나 회분함량은 외국산 제품에 비하여 약간 낮고, 반면에 조지방 및 조단백 성분의 함량은 약간 높게 나타나고 있어 대체적으로 본 연구에서 얻어진 엑기스내의 비풍미성분(non- fla-vour component) 함량은 외국산에 비하여 많은 차이가 없다. 8) 수입 외국산에 비하여 국산엑기스(본 연구에서 ethyl alcohol로 추출)내의 무기성분등의 함량은 비교적 낮은 편이다. 9) 건강에서부터 oleoresin을 얻어 paradol을 제거시킨 후 순수한 gingerol을 분리하여 IR과 NMR로 확인한 결과, 국산건강의 엑기스에는 주로 6-gingerol이고 약간의 10-gingerol이 함유된 것으로 나타났다. 10) 순수하게 분리된 gingerol을 열분석(TGA와 DTG)한 결과 약 $75^{\circ}C$에서 gingerol의 열분해 반응이 일어남을 알수 있었다. 11) 건강 분말시료와 엑기스내의 미생물 검사 결과 건강분말에서는 세균수가 많이 존재하는 것으로 나타났으나, 이는 ethyl alcohol로 추출하는 공정 중 대부분의 균들이 사멸된 것으로 나타났다. 12) 관능적 측면에선, 본 연구에서 제조한 엑기스와 수입엑기스를 비교한 결과 생강 특유의 맛은 비슷했으나, 수입엑기스에서는 쓴맛과 톱밥냄새를 느낀다는 결과를 나타내었으며 전체적인 종합적 풍미는 국산 건강엑기스가 좋은 것으로 나타났다.