• Journal of Soil and Groundwater Environment
• /
• v.13 no.6
• /
• pp.85-92
• /
• 2008

Water in Soyang River is an essential source for citizens of Chuncheon and Seoul areas. In 2006, turbid water in Soyang River aggravated by the typhoon Ewiniar, sustained for over 280 days unlike conventional years, then which interrupted water supply of Chuncheon and Seoul areas. Soil erosion derived from high cool lands constituting about 55% of Soyang River area is considered one of main causes for the turbid water, including imprudent development of mountainous area, road expansion, and road construction for forestry. According to analysis of turbidity, precipitation and reservoir level in Soyang River region for June 2006${\sim}$August 2008, the turbidity showed a peak correlation (r = 0.28) at a lag time of 49 days and especially did an excellent correlation (r = 0.60) with the reservoir level at a lag of 4 days. In the meantime, a critical turbidity of 31 NTU at Soyanggang Dam was estimated, over which would cause turbid water at Paldang Dam. In addition, a master recession curve was suggested, from which sustaining time of turbid water can be predicted.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.10
• /
• pp.67-75
• /
• 1998

This paper examined the geometrical variables of microstrip to control the characteristic impedance of MCM interconnect and also with respect to the practical requirements, evaluated the critical lengths for attenuation, propagation delay, and crosstalk at 500 MHz frequency compared to at 50 MHz frequency. With the illustration of each MCM-L and MCM-D interconnect having 50 characteristic impedance, it was revealed that the most important geometrical variables to control the characteristic impedance of microstrip are eventually dielectric thickness and line width. In particular, the dielectric thickness of MCM-D interconnect must be controlled with tolerance below 2 m. It is clear that the attenuation does not give rise to signal distortion in the range of up to 500MHz frequency for both MCM-L and MCM-D interconnects. However, the propagation delay is so significant that both MCM-L and MCM-D interconnects should be matched with load at the 500 MHz frequency. For the MCM-D interconnect, the crosstalk voltage would not be high to generate the wrong signal on the neighboring line at 500 MHz frequency, but the MCM-L interconnect could not be used due to severe crosstalk. Eventually, it is clear that the transmission line behavior must be studied for the design of MCM substrate at the 500 MHz frequency.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.3 no.4
• /
• pp.47-60
• /
• 1999

The stability and efficiency of structural control systems depend on the accuracy of mathematical model of the system to be controlled. In this study, state equation models of a small scale test structure and an AMD(active mass damper) are obtained separately using OKID(observer/Kalman filter identification) which is a time domain system identification method. The test structure with each floor acceleration as outputs is identified for two inputs - the ground acceleration and the acceleration of the moving mass of AMD relative to the installation floor - individually and the two identified state equation models are integrated into one by model reduction method. The AMD is identified with the motor control signal as an input and the relative acceleration of the moving mass as an output, and it is shown that the identified model has large damping ratio and phase shift. The transfer functions and the time histories reconstructed from the identified models of the test model and the AMD match well with those measured from the experiment.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.1
• /
• pp.1-11
• /
• 2009

In this paper, a new 1 kW power amplifier with high efficiency and high stability in a RF generator is designed and fabricated for plasma applications. The efficiency of power amplifier is improved by using class-E amplifier that consists of one push-pull MOSFET and high current drive IC instead of class-C amplifier composed of several single ended MOSFET. Switchable damper that allows selecting three different modes of amplifiers for considering efficiency and stability is added into the amplifier for plasma applications. Stable region of an early electronic discharge section is extended to VSWR of 4.5:1 compared to conventional VSWR of 3.8:1 through using switchable damper. The dimension of the amplifier is also reduced to 30 % of conventional amplifier. The 80 % efficiency of power amplifier with switchable damper is obtained the output power of 1 kW in operating frequency of 13.56 MHz. In comparison of conventional power amplifier for plasma applications, 13 % efficiency is improved.

• The Journal of Engineering Geology
• /
• v.13 no.1
• /
• pp.129-137
• /
• 2003

We interpreted the seismic signal characteristics from crosswell seismic tomography in the underground cavity like abandoned mines. The first arrival time delay and amplitude attenuation showed clearly at the low velocity zone of cavity and fracture. Also ray density decreased by detour of raypath. As a result of the amplitude spectrum analysis of fresh rock and low velocity zone, there were no noticeable differences of the amplitude up to about 1000Hz frequency, but indicated that the one passed around cavity decreased about 7dB at 2000Hz, and 20dB at 3000Hz. It was possible to compare the signal characteristics between two media by extracting the signal data from the fresh rock zone and the underground cavity through the seismic crosswell tomography.

• Geophysics and Geophysical Exploration
• /
• v.15 no.2
• /
• pp.85-91
• /
• 2012

Multiple Lapse Time Window (MLTW) analysis for obtaining intrinsic attenuation value require numerous data without directional bias to compensate focal mechanism. The first window of MLTW, therefore, shows large deviation in fitting smoothed theoretical curve. The information on the focal mechanism may reduce burdens of number and distribution. This study combined algorithm of computing focal mechanism to DSMC method by Yoshimoto (2000). However, the MLTW method based on the numerous data was not applicable to this study, because of the limited data to the almost same fault plane solution. This study showed that the available data was too insufficient to construct smoothed theoretical curve, although the deviation of the first window was improved. Instead of conventional solution by more data, the study seems to be needed for new constraints to obtain smoothed curve.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.4 s.346
• /
• pp.31-38
• /
• 2006

In this paper, we propose an efficient preceding scheme for STBC-Spatial Muiltiplexing OFDM systems. In MIMO systems, the precoder is designed on the assumption that feedback channel information is perfectly known to transmitter and receiver. However, feedback delay and link errors in real environment make the transmitter use the incorrect channel information and consequently cause the performance degradation. The proposed precoder is designed to compensate for the performance degradation by the diversity gain provided by STBC. At the transmitter, the precoder for each subcarrier is constructed by using the index of codebook, subcarrier correlation, and auto correlation of channel. From the simulation results, STBC-spatial multiplexing OFDM outperforms the preceded-spatial multiplexing OFDM at $SER=10^{-3}$ when the Doppler frequency is greater than 60Hz.

• Geophysics and Geophysical Exploration
• /
• v.13 no.3
• /
• pp.277-285
• /
• 2010

For regional earthquakes in the Korean Peninsula, the seismic Lg waves have the largest amplitude. Our researches in South Korea found that more reasonable low ${Q_{Lg}}^{-1}$ was obtained as the inter-station distances increase. The other methods such as coda normalization method and multiple lapse time window method also produced that the low ${Q_{Lg}}^{-1}$ is related to the values of seismically inactive region.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.3
• /
• pp.60-65
• /
• 2000

We propose a new method to deal with the optimal gain self-tuning of the PID controller which is used to industrial process control in various fields. First of all, in this method, first order delay system which was modeled from the unit step response of the system is Pade-approximated, then initial values are determined by the Ziegler-Nickels method. Finally, we can find the parameters of Pm controller so as to maximize the fuzzy inferencl function which includes the maximum overshoot, damping ratio, rising time and settling time. The proposed method also shows good adaptability for variations in characteristics and dead time of the system.

• Computational Structural Engineering
• /
• v.7 no.1
• /
• pp.25-30
• /
• 1994

본 고에서는 강한 바람이나 지진에 의한 고층 구조물의 진동을 감소시키기 위하여, 능동제어장치가 효과적으로 사용될 수 있음을 보이었다. 그러나 능동제어장치를 실제 구조물에 널리 적용하기에는 아직 많은 문제점들이 남아있다. 첫째, 효과에 비해 고가의 진동제어장치가 필요하며 유지관리에도 많은 비용이 필요하다. 또한 진동제어장치가 원활히 작동하기 위해서는 계속된 에너지의 공급이 있어야 하는데, 지진과 같은 과도한 구조물의 진동시 이를 보장할 수는 없다. 그러므로 극한상황에서는 진동을 오히려 증폭시킬 수도 있다. 둘째, Control Force의 산정시 사용되는 목적함수의 가중행렬을 결정하는 정형화된 방법이 아직 존재하지 않으며 효율적인 산정을 위해서는 많은 시행착오가 필요하다. 그밖에도 복잡한 실제 구조물의 단순한 모형화에 따라서 여러 문제점들이 발생하기 쉬우며, 실제 제어시에는 시간지연효과나 측정되지 못한 거동에 의한 문제 등이 있다. 구조물의 진동 저감방안에 대한 지금까지의 연구결과로는, 일반적인 경우에 있어서는 Base Isolator와 같이 재료의 감쇠특성을 이용하는 방법이 추천되고 있으나, 현재 내진설계된 고층건물과 같은 대형 구조물의 진동제어 등의 몇몇 경우에 있어서 능동제어의 필요성이 인정되고 있다. 좀더 안정적이고 효율적인 제어기법의 개발에 의해 많은 실제 구조물에 적용 범위를 넓힐 수 있을 것으로 기대된다.