• Transactions of the Korean Society of Mechanical Engineers
• /
• v.3 no.3
• /
• pp.124-131
• /
• 1979

An optimim reduction gear ratio problem for a subway rapid transit car in Seoul was solved by using a computer program package, which is a modified and extened version of the simple model by Mischke. The optimum value of reduction gear ratio was evaluated by minimizing the total start-to stop time.The validity of the computer program package was verified by cross-checking the calculated values of gear ratio and dynamic characteristics with the actual and measured values.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.617-621
• /
• 1993

우주는 무중력, 또한 초고진공의 세계이다. 우주에서 기계가 작동할 때, 운동 저항은 마찰력과 관성력만이 작용한다. 여기서 관성력은 가속, 감속 일 때만 작용하며 그 힘은 정확하게 계산하여 얻을 수 있다. 이것에 대하여 마찰력은 접촉면에 항상 존재하며, 또한 비정상이다. 본 연구에서는 피막재로서 앞서의 보고에서 이미 유효성이 나타난 바 있는 In을 사용하여 마찰 반복수에 따른 마찰관계변화에 미치는 Pin, disc의 표면 거칠기의 변화의 영향을 명확하게 밝히고, 초고진공중에 있어서 Tribo-Coating법에 의한 In막은 윤활기구를 검토하고자 한다.

• Proceedings of the IEEK Conference
• /
• 2000.06e
• /
• pp.35-38
• /
• 2000

Since the telemanipulator consisting of high reduction ratio gear joints has a slow dynamics comparing with the master manipulator, its control signal is likely to be saturated resulting in poor tracking performance and deteriorated stability. This paper proposes a bilateral control scheme of a telemanipulator having high reduction ratio, which can compensate the control input saturation. The experimental results show that the proposed control scheme has excellent performances.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.380-388
• /
• 2016

Using the magnet gear, it is possible to transmit power without mechanical contact. As the drive shaft in a magnet gear-based speed reducer system is isolated from the drive shaft, the system is a two-inertia resonance system that should cope with an external load with the limited air-gap stiffness. On the other hand, the drive shaft or low-speed side is controlled only by the torque of the drive shaft through an air-gap, and the excessive oscillation or the slip can then be generated because of an abrupt disturbance that is different from the general mechanical gear system. Therefore, the disturbance loaded at the low speed side should be measured or estimated, and considered in the control of the driving shaft. This paper proposes a novel full-state feedback controller with a reduced-order observer for the speed reducer system using a magnet gear with a unified harmonic modulator. The control method was verified by simulation and experiment. To estimate the load at the low speed side, a novel observer was designed, in which the new state variable is introduced and the new state equation is formulated. Using a full-state feedback controller including the observer, the test result against disturbance was compared with two D.O.F PI speed controllers. The pole slip was compensated within relatively a short time, and the simulation result about the estimated variable shows a similar tendency to the test result. The test results showed that the magnet gear-based reducer can be applied to an accurate servo system.

• Journal of the korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.67-72
• /
• 1993

Wall wetting phenomenon in the intake port of an MPI engine was investigated with different kinds of injectors by an A/F step response test and analysis was done based on the simple wall wetting model to find out a certain correlation between wall wetting and A/F variations. It was found that (1) At fully warmed condition of 90.deg.C water temperature, around 40-60% of injected fuel was wall wetted, (2) At cold condition of 45.deg.C Water temperature, around 68-80% of injected fuel was wall wetted, and (3) A/F variations during acceleration and deceleration were influenced by the wetting area, the fuel droplet size, and the amount of wall wetting fuel.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.18 no.1
• /
• pp.41-47
• /
• 2012

Recently, due to the rapid rise of the international oil price, the burden of fuel oil expense is relatively increasing in a ship. And the international restriction of the greenhouse gas which was generated from the burning of fuel oil is also rapidly strengthened. Therefore, to reduce the greenhouse gas and fuel oil consumption, many shipping company adopted the low speed navigation and it was focused on the improvement of fuel consumption efficiency and the usage of alternative energy in the marine engine development field. In this paper, the fuel oil consumption according to the ship's speed was measured in the actual seas and analyzed the shop test results in the shipyard and the ship navigation data from the abstract log. And then it was proposed that the ship's economic speed was 14~15kts and the optimum rpm was 140~150 in specific sea conditions.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.4
• /
• pp.47-54
• /
• 2019

In the worldwide, The issue comes up which is the danger of car accidents from climate-change effects. We are considering about various types of speed limit signs for setting restricts to high-speed vehicles. South Korea has 4 seasons in the land. At Summer or Winter seasons have heavy rains and fogs or snow, In these seasons need to enforce speed limit laws or methods to prevent car collision. But South korea is using stationary speed limiters that is not enough to proof against rear-end car accidents in these climates. In this paper shows the necessity of independent LED speed limits display to reduce car accidents. And explaining the prototype model which is a combination of rain sensor and wiper systems. This model is independently changed the speed limits to 50%, 80%, 100% of standards by raindrops and snowflake. Also it is freely setting speed limits on each places anywhere it settled in. Visual effects of the model as being speed-down of vehicles helps to prevent rear-ending car accidents and traffic beforehand.

• Journal of the Korean Institute of Gas
• /
• v.28 no.1
• /
• pp.59-64
• /
• 2024

In this study, we conducted research on a miniaturized transmission system suitable for ultra-compact electric vehicles, such as electric arts or small electric cars. While conventional electric vehicles eliminate multi-gear transmissions and control motor output or secure initial driving force through reducers, in vehicles like electric karts or compact electric cars, which have relatively small battery capacities, the driving range can be reduced or the motor can be stressed epending on the loading state. Therefore, in this study, we developed a low stage ratio 0.625 and high stage ratio 1.6 a two-stage transmission system that can change gears as needed, considering factors such as slope conditions and loading status, by applying the continuously variable transmission (CVT) mechanism. Based on the selected gear ratios, we designed the transmission and created a test rig to verify the power transmission efficiency of the developed transmission. Using the test rig, we varied the rotational speed and load of the transmission to confirm its power transmission characteristics and also examined the heat generation characteristics during shifting and operation. As a result, developed a two-stage transmission with a CVT structure.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.14 no.7
• /
• pp.914-919
• /
• 2004

When the motor is rotating, the torque and rpm are varying as the loads or the driving status connecting through reduction units are changing. On the contrary, one can monitor the changes of the loads or the driving status in the manner of measuring motor torque and rpm. There is a torque measuring method using the strain gauge and bridge circuit. But, because this is the contact method, it has the life time which is dependent on rotating velocity and used time. So this system demands on replacement of some Parts or whole system itself for maintenance. And this system is also relatively big and expensive, requiring preceding annoying process. In this paper, we are going to suppose non-contact method to measure torque and rpm using the Hall effects sensor For this we have made the planetary geared reduction motor with Hall sensors and with the monitoring system. The monitoring system displays the sensing data(torque, rpm) and calculated data( power) and also has the network capability with Bluetooth protocol. Our solution is much more inexpensive ;md simple method to measure torque and rpm than before.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.11
• /
• pp.979-986
• /
• 2016

The tripod shafts of constant-velocity joint are used in both the trains KTX and KTX-sanchon. It is an important component that connects the motor reduction unit and the axle reduction unit in a power bogie. The tripod shaft not only transmits drive and brake torque in the rotational direction, but also slides in the axial direction. If the drive system is loaded with an excessive torque, the fuse part of the shaft will be fractured firstly to protect the other important components. In this study, a rig was developed for conducting torsion tests on the tripod shaft, which is a type of mechanical fuse. The tripod shafts were subjected to torsional fracture test and torsional fatigue test on the rig. The weak zone of the tripod shaft was identified, and its fatigue life was predicted using finite element analysis (FEA). After analyzing the FEA results, design solutions were proposed to improve the strength and fatigue life of the tripod shaft. Furthermore, the deterioration trend and time for failure of the tripod shaft were verified using the hysteresis loops which had been changed with the advancement of the torsional fatigue test.