• Proceedings of the KAIS Fall Conference
• /
• 2010.05b
• /
• pp.1000-1003
• /
• 2010

기존 Non-Road 가솔린 불꽃점화 소형엔진의 경우 대부분이 캬브레이터 연료 공급 방식으로 연비 및 배기가스 성분이 매우 열악한 실정이다. 본 연구에서는 이러한 단점을 극복하고 배기규제에 대응하기위하여 전자제어식 연료분사방식으로 엔진을 변경하고, 관련핵심 부품의 설계 및 개발을 수행하였다. 전자제어식 소형엔진에 적합한 인젝터, 연료펌프를 선정하였으며 연료레일은 새로이 설계하여 장착하였다. 최적의 인젝터, 연료펌프 및 흡기포트를 선정하기위해 각각의 핵심 부품에 대한 성능개발을 수행하였다. 제작된 소형엔진은 엔진성능 개발을 통하여 연비 및 배기가스를 개발할 예정이다.

• Journal of the Korean Institute of Gas
• /
• v.16 no.3
• /
• pp.48-53
• /
• 2012

The purpose of this paper studies the failure cases including with system of liquefied phase injection in liquified petroleum gas vehicle. The first case, resulting with inspection the injector of LPG, it occasionally certified the injection damage phenomenon that the fuel efficiency(km/l) was decreased to 5% by carbon deposit with injector hole when the driver operates the vehicle. The second case, it certified the interference phenomenon of air flow with carbon deposit in ISA system control for idle speed of engine and throttle body suppling air into engine. As a result, the fuel efficiency was decreased 7%. The third case, the outer air during intake stroke was intermittently flowed in this gasket gap because of weaken adhesion power phenomenon for cylinder block by intake manifold gasket tearing. Consequentially, it certified the decrease for fuel efficiency to 3% by risen the amount of fuel injection as the air inflow quantity. These failure examples reduced the power performance of engine and the fuel efficiency of vehicle. It have to minimize of failure phenomenon preparing through quality management.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.87-94
• /
• 2003

Recently, LPLi(Liquied-Phase LPG injection) system is studied for the new stringent emission regulations. But , there are some problems to be solved such as injector tip icing and fuel leakage for LPLi system development. In this paper, the icing problem near injector tip which leads to difficulty of accurate A/F control was studied and reported. Icing of injector tip and port wall was observed at all the cases in this study regardless of injection duration and angle, air humidity change. The spray angle of LPLi was observed approximately two times wider than that of Gasoline injection. This makes the LPLi spray collide with intake port around injector tip. Temperature of the wetted area was decreased and icing of water vapor contained in intake air because of evaporation of the fuel film. The ice of the injector tip and port wall is also affected by the materials related to heat transfer.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.04a
• /
• pp.8-8
• /
• 1999

2-유체 인젝터의 분무연소에 대한 통찰 및 구조에 대한 이해와 연료-공기 혼합과 연소반응의 물리적 이해에 필요한 수치적 모델의 개발 및 검증을 위해서는 2유체 시스템에서 액체 및 기체 각각의 기본적 특성인 액적크기, 액적속도, 액적의 질량플럭스(flux), 가스상의 속도측정 등이 필요하다. 특히, 액체분무에서는 액적의 크기를 예측하는 것이 매우 중요한 과제이며, 액적의 크기에 영향을 주는 인자들로는 노즐의 형태, 분사액체의 물성치(점도, 표면장력, 밀도), 주위기체의 조건(온도, 압력, 응축과 증발현상), 분사압력 등이 있다. 그러나, 실제 분무액적의 크기는 분포를 가지므로 같은 SMD를 가지더라도 그 분포의 정도는 크게 다를 수 있어 결과적으로 분무액적의 크기를 평균값만으로 표현하는 것은 불충분할 뿐만 아니라 그 적용에도 한계를 가지게 된다. 따라서 분무액적의 평균크기와 함께 그 분포의 정도 등을 함께 나타내려는 시도가 많은 과학자들에 의하여 연구되었다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.2
• /
• pp.39-44
• /
• 2004

As air pollution has become an important issue across the world, studies of clean fuel are on going to reduce combustion emissions. One example is development of the LPLi(Liquefied Phase LPG injection) engine. Some problems are occurred during development. One of the problems is icing phenomenon at injector tip due to evaporation potential heat when liquid LPG is injected. If the Icing is raised at injector tip or injector inserting hole, it disturbs fuel injection. And if the ice particles are inducted into cylinder, it brings problems associated with control of emission and air/fuel ratio. In order to solve the problems, a rig system was set up and observed Icing of injector tip. Engine test was carried out for visualization of injector tip icing and its effects on combustion and emissions.

• Journal of the Korean Institute of Gas
• /
• v.16 no.2
• /
• pp.38-44
• /
• 2012

In recent years, the need for more fuel-efficient and lower-emission vehicles has driven the technical development of alternative fuels such as LPi (Liquid phase LPG injection) which uses pump for the high pressure supply of liquid LPG fuel and is able to meet the limits of better emission levels while it has an advantage of higher power. Although it has the advantage of power and lower emission levels, the characteristics of LPG, such as high vapor pressure, lower viscosity and surface tension than gasoline fuels makes it difficult design system. Therefore most fuel pumps and injectors are imported. In the present study, in order to domestically develop LPG injector which guarantees flow rates and optimal operation, the experimental investigation on leakage and flow rate characteristics of developed prototype injector was carried out at the bench test rig for developed injector.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.207-210
• /
• 2005

The results of combustion performance test of fuel-rich gas generator with dual swirl injectors are described. By changing simulating duct and recess number(RN) of the injectors, we inspected whether the combustion instability took place. When the injectors of RN = 0.5 were used, combustion instabilities could be reduced using the simulating duct. However, the effect of the simulating duct on the gas generator with the injectors of RN = 1.5 was not significant.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.10a
• /
• pp.205-209
• /
• 2004

The configuration and arrangement of injector in LRE gas generator and combustor have a great impact on combustion process and heat exchange because of affecting atomization, vaporization, mixing and chemical reaction. A relation between injector array and mixing distribution of propellants based on a physical approach was investigated in this study. Programming method of this relation is used to predict mixing distribution of propellants. Simplicity of physical approach and various assumptions make it reduce the accuracy and application of the results of present study. But, this method is very useful to predict the mixing distribution of full scale combustor due to difficulties in cold flow testing.

• Journal of the Korean Institute of Gas
• /
• v.16 no.6
• /
• pp.23-28
• /
• 2012

The LPG engine technology in Korea has made significant advances with the mass production of LPG vehicle with liquid phase LPG injection system, and have reached to satisfy the SULEV emission regulations. As of now, domestic production of LPG fuelled vehicles in Korea have reached more than 2.4 millions, which is the best in the world. But in the technical point of view, the key technologies for fuel injection system of LPG fuelled engine are mainly dependent on foreign license. Especially, fuel injector in the liquid phase LPG injection system has been imported from C company, which supplies LPG injector worldwide in the name of model D. In the context, it is quite urgent to develop the LPG injector technology in Korea. In this study, WCC coating which is key technology to develop LPG injector by reducing the fuel leakage was developed and tested. Considering the fuel leakage of 0.06cc/min in commercial LPG injector, fuel leakage was reduced down to 0.04cc/min with WCC coating technology and optimization of injector structure.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11b
• /
• pp.839-841
• /
• 2010

기존의 범용 가솔린 소형엔진의 경우 대부분이 캬브레이터 연료 공급 방식으로 연비 및 배기가스성분이 매우 열악한 실정이다. 본 연구에서는 이러한 단점을 극복하고 배기규제에 대응하기위하여 전자제어식 연료분사방식으로 엔진을 변경하고, 관련핵심 부품의 개발을 수행하였다. 전자제어식 소형엔진에 적합한 인젝터, 연료펌프를 선정하였으며 연료레일은 새로이 설계하여 장착하였다. 최적의 작동조건을 선정하기위하여 엔진의 성능개발을 수행하였다. 개발된 소형엔진은 기존의 캬브레이터 방식의 엔진 대비 우수한 연비개선 효과와 배기가스 저감 효과가 있었다.