• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.5
• /
• pp.430-435
• /
• 2013

This study is investigation of the characteristics for acoustic emission signal generated by destruction on glass fiber bundles and specimen that was machined composite materials surrounding the outside of GFRP cylinder. The Amplitude of acoustic emission signal gets bigger as the cutting angle of knife increases. Accordingly, the number of hits in destruction of composite materials specimen have more in longitudinal direction (longitudinal direction to the glass fiber) than in hoop direction (horizontal direction to the glass fiber) while the amplitude of signals were bigger in hoop direction than longitudinal direction. It was found out that the amplitude of the glass fiber breakage is more than 40 dB and that the amplitude of signal for matrix crack was less than 40 dB because matrix crack signal was not observed when threshold value is 40 dB and matrix crack signal suddenly appered when threshold value is 32 dB. The slope of the amplitude is related to the acoustic emission source and the slope of the amplitude of the horizontal and vertical directions are 0.16 and 0.08. In particular, The slope of the amplitude of longitudinal direction breakage appear similar to the glass fiber breakage and therefore Acoustic emission source of longitudinal direction breakage is estimated the glass fiber breakage.

• Food Science and Preservation
• /
• v.13 no.1
• /
• pp.1-7
• /
• 2006

The effects of packaging material and method on quality of fresh-cut mushrooms (Agaricus bisporus Sing.) were investigated in terms of weight loss, surface color, phenolics, vitamin C and sensory characteristics during storage at $5^{\circ}C$. The fresh-cut mushrooms were subjected to passive, gas exchange and vacuum packaging conditions at st. Polyethylene film (PE), polypropylene film (PP), anti-fogging film (AP) and pen orated film (PF) were used for the passive packaging. The mixed gas of $5\% CO_2/\;2\%O_2$ (MA1) and $10\%CO_2/\;2\%O_2$(MA2) were applied for the gas exchange packaging. The respiration rate of sliced mushroom was 1.27 times higher than intact mushroom at $5^{\circ}C$. Gas concentrations in the passive packaging were $1-2\%\;O^2\;and\;5-16\%m$ during storage of sliced mushrooms for 14 days at $5^{\circ}C$, and levels of the gases were different by the films used The mushroom in perforated film (PF) showed the highest weight loss of $4.56\%$. Anti-fogging film (AF) was somewhat effective for prevention of the weight loss compared with other films after 14 days storage. The mushrooms in MA1 and MA2 packages showed lower delta L value than in other films. PE packaging mitigated decrease of free and bound phenolics during storage. The mushrooms in MA2 kept better quality in sensory aspect, and then in MA1, PE and PP in order during storage at $5^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.166.2-166.2
• /
• 2016

최근 생산 장비의 발달로 인해 절삭공구, 전기전자 부품, 항공 및 자동차 부품 생산에 필요한 생산 장비의 수명연장, 고속 절단 및 고성능화가 중요시 되면서 우수한 내구성, 내마모성 및 고온 안정성을 갖는 기계부품 및 공구를 요구하게 되었다. 내마모성을 가지는 표면을 얻기 위해서는 TiN, TiC, AlN, Al2O3, CrN, ZrO2와 같은 경도 높은 물질을 증착하여 특성을 개선시키는 방법이 있다. 특히 AlN은 비교적 우수한 경도와 고온 안정성을 가지고 있어, 생산 장비의 고속 절단 및 반복되는 정밀 작업으로 인한 열충격과 마모를 완화시키는 역할을 하는 코팅재로 사용하기 적합하다. 본 실험에서는 RF-magnetron sputtering 방법을 이용하여 AlN 박막을 파워 150W, 질소가스 분압비에 따라 25%, 50%, 75%, 100%의 조건으로 금속기판 위에 증착하였다. 금속 기판 위에 제작된 AlN막은 XRD (X-ray Diffraction)을 사용하여 배향성을 확인하였고, HM-220 (Micro-vickers hardness tester)을 사용하여 AlN박막의 경도를 측정하였으며, SEM (Scanning Electron Microscope), AFM (Atomic Force Microscope)을 이용하여 표면의 구조와 거칠기를 측정하였다. 이 실험을 통하여 우수한 물성과, 치밀한 조직의 AlN박막이 고속 절삭 공구, 유공압 실린더, 베어링과 같은 금속부품의 코팅소재로 적용가능 할 것으로 기대된다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.6
• /
• pp.837-844
• /
• 2001

Jet cutting technology currently makes use of a generic supersonic gas jet to improve the cutting speed and performance. In order to get a better understanding of the flow characteristics involved in the supersonic jet cutting technology, the axisymmetric Navier-Stokes equations have been solved using a fully implicit finite volume method. Computations have been conducted to investigate some major characteristics of supersonic coaxial turbulent jets. An assistant gas jet has been imposed on the primary gas jet to simulate realistic jet cutting circumstance. The pressure and the temperature ratios of the primary and assistant gas jets are altered to investigate the major characteristics of the coaxial jets. The total pressure and Mach number distributions, shock wave systems, and the jet core length which characterize the coaxial jet flows are strongly affected by the pressure ratio, but not significantly dependent on the total temperature ratio. The assistant gas jet greatly affects the basic flow characteristics of the shock system and the core length of under and over-expanded jets.

• Journal of the Korean Institute of Gas
• /
• v.9 no.2 s.27
• /
• pp.38-42
• /
• 2005

This study introduced concept of safety valve about development of valve for LP gas cylinders. LP gas cylinders are used more because of convenience of use, but a lot of accidents are occurred. Specially, it is used by purpose to injure glossary or others and is sometimes used to a demonstration tool. Korean government was making mandatory to use overuse cutoff valve to reduce accident, but it is real condition that product development is not following. In this study, introduce concept of safety valve that introduce more original safety concept than overuse cutoff valve. This was developed by method that insert module to present use valve and flowing of gas is controlled in state that hose or regulator un-connects to valve. Also, flowing of gas cut-off immediately if hose is cut or occurrence of overuse is produced even if is using normally.

• Journal of the Korean Institute of Gas
• /
• v.19 no.4
• /
• pp.55-61
• /
• 2015

In this paper, the displacement behavior characteristic of hollow rollers with various cross sectional area profiles and circular plate for load supporting capacity increment has been presented using a finite element method. The FEM results present that the hollow roller with X-shaped or Y-shaped columns between outer tube, middle tube and inner tube reduces a maximum displacement at the middle length of hollow rollers. And the circular plate, which is inserted at the middle of the hollow roller, is very useful to reduce the maximum displacement of hollow rollers with the plate thickness of 30~40mm. This paper presents the weight vs the maximum displacement ratio in which is represented for the optimized design as a function of a hollow roller total weight. The FEM analyzed results recommend the design model 4, 5 and 6 of hollow rollers for decreasing the ratio of maximum displacement and total weight of hollow rollers.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.4
• /
• pp.639-647
• /
• 2022

The use of flames is essential in cutting, bending, and welding steel during a ship's construction process. While acetylene fuel is commonly used in steel cutting and the manufacturing process in shipyards, the use of propane as an alternative fuel has recently been increasing, due to the lower risk of explosion and propane's relatively low calorific value. However, propane fuel has a relatively slow processing speed and high slag generation frequency, thereby resulting in poor quality. Propylene is another alternative fuel, which has an excellent calorific value. It is expected to gain wider use because of its potential to improve the quality, productivity, and efficiency of steel processing. In this study, the combustion characteristics of propane and propylene fuel during steel plate processing were analyzed and compared. The reduction of greenhouse gases and other harmful gases when using propylene flame was experimentally verified by analyzing the gases emitted during the process. Heat distribution and tensile tests were also performed to investigate the effects of heat input, according to processing fuel used, on the mechanical strength of the marine steel. The results showed that when propylene was used, the temperature was more evenly distributed than when propane fuel was used. Moreover, the mechanical tests showed that when using propylene, there was no decrease in tensile strength, but the strain showed a tendency to decrease. Based on the study results, it is recommended that propylene be used in steel processing and the cutting process in actual shipyards in the future. Additionally, more analysis and supplementary research should be conducted on problems that may occur.

• Journal of the Korean Society for Precision Engineering
• /
• v.4 no.4
• /
• pp.84-92
• /
• 1987

To investigate the influence of the cutting pressure on the laser cutting quality, an expermental facility was constructed which can measure the cutting pressure distribution for various cutting conditions. Flow visualization was performed using the Schlieren photography and the pressure acting on the workpiece surface was measured, corresponding to the important process variables such as the kind of assist gas, nozzle pressure, distance between the nozzle exit and the workpiece surface, and the presence of the secondary nozzle. The cutting pressure acting on the workpiece was largely influenced by the nozzle pressure and nozzle-workpiece distance. The secondary nozzle which is used to raise the effective working pressure had its obvious role only when the angle between it and the main nozzle was small and when the distance between the nozzle exit and the workpiece surface was large.

• Proceedings of the KAIS Fall Conference
• /
• 2011.12b
• /
• pp.379-381
• /
• 2011

본 논문에서는 피복아크용접(SMAW)을 자동용접으로(GMAW) 전환시키기 위한 기초 연구로서 GMA용접가스가 기공율에 미치는 영향을 보고자 한다. 기공율 평가를 위해 반자동 소방용 분기배관실험장치를 제작하였다. 분기배관의 기공율을 평가하기 위해 보호가스 3종(Ar, $CO_2$, 8:2 혼합가스), 전압을 변수로 설정하여 GMA용접을 실시하였다. 용접을 실시한 시편을 용접방향으로 절단하여 기공율 평가를 실시하였다.

• Journal of the Korean Institute of Gas
• /
• v.16 no.5
• /
• pp.52-57
• /
• 2012

This study presents sealing characteristics of multi-contact o-rings as functions of strain, compression stress, and contact normal stress using a FEM technique. The FEM results on the sealing characteristics show that the maximum strain, maximum compression stress, and maximum contact normal stress of multi-contact o-rings are approximately 1.7 times higher than those of conventional o-rings. This is due to a U-grooved cross section of multi-contact o-rings, and the multi-contact o-rings with a U-groove show more effective in sealing for high pressure vessels, valves, and gas equipments. And the extrusion failure in the multi- contact o-ring does not produce for an increased gas pressure due to a U-groove. This may extend sealing life compared to that of a conventional o-ring.