• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.10
• /
• pp.1126-1135
• /
• 2007

This paper presents the varactor-tuned miniaturized hairpin tunable filter with a single control voltage. The previously proposed miniaturization method is a very straight-forward method to miniaturize a parallel coupled-line filter. In this paper, the miniaturized hairpin tunable filter is proposed with the constant ratio rule of that the capacitances of the each stage always have constant ratio without any dependency to miniaturized electrical length. To show the validity of the proposed method, a 3rd order 0.5 dB ripple Chebyshev fitter with a center frequency of 900 MHz and a fractional bandwidth(FBW) of 10 % was designed and fabricated. The fabricated filter was based on CER-10 substrate of Taconic Inc. with 1SV277 varactor diode of Toshiba Inc. The center frequency of the fabricated filter can be changed from 606 MHz to 944 MHz, 338 MHz with the control voltage from 0.5 V to 4 V. The insertion loss of the proposed filter is increased with the increment of the control voltage, and the filter characteristics are well reserved expect of slight change of the bandwidth with the various control voltage.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.3 s.333
• /
• pp.25-32
• /
• 2005

In this papers, we first, therefore, designed VCO(voltage controlled oscillator) that is composed of the dielectric resonator and the varactor diode, and then designed and fabricated PLDRO(phase locked dielectric resonator oscillator) that is combined with the sampling phase detector and loop filter. The measured results of the fabricated PLDRO at 12.05 [GHz] show the output power is 13.54 [dBm], frequency tuning range approximately +/- 7.5 [MHz], and Power variation over the tuning range less than 0.2 [dB], respectively. The phase noise which effects on bits error rate in digital communication is obtained with -114.5 [dBc/Hz] at 100 [KHz] offset from carrier, and The second harmonic suppression is less than -41.49 [dBc]. These measured results are found to be more improved than those of VCO without adopting PLL, and the phase noise and power variation performance characteristics show the better performances than those of conventional PLL.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.6
• /
• pp.575-583
• /
• 2003

In thesis we applied the short or open reflection type for IQ vector modulator The open or short type is operated even exception of other redundancy circuit. Generally IQ vector modulator uses MESFET in performing reflection open or short, then minus voltage which is having complex structure is required to operate MESFET via IQ signal. However BJT can be substituted for MESFET, BJT is improved characteristics like as cutoff frequency, electron mobility and so on. We used BJT in IQ vector modulator which is compatible with TTL level in I,Q digital signal, and attached AGC function. We got the result of operations within ${\pm}$ 1$^{\circ}$ phase and ${\pm}$ 0.6 dB amplitude Variation With full range of 20 dB and Variation of ${\pm}$ 6$^{\circ}$ Phase and ${\pm}$ 0.5 dB amplitude Versus full temperature range.

• 전자공학회논문지 IE
• /
• v.43 no.3
• /
• pp.22-27
• /
• 2006

This paper presents the control system of high-efficiency automotive 35W metal-halide lamp ballast using the new control method and planar transformer. In this paper, the electronic ballast is designed so that digital control method by microcontroller can be applied to the electronic ballast for the lamp requirement and peripheral environment in order that metal-halide lamp, which has the complicated transient features, is to be applied to the automobile even if it has superior features in brightness, color rendering, light efficiency, and lifespan compared to the conventional halogen lamp. Also, the efficiency increase of the ballast is devised by being varied the switching frequency of Flyback Converter following the battery input voltage of the automobile. Being designed for high-frequency switching transformer of converter in planar form, reduction of loss, weight, overall size are realized and efficient power control in the automobile that had the limited energy and the limited space of battery is devised. The results of the proposed system is verified through various experiment results.

• 한국전산유체공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.35-38
• /
• 2005

인버터는 전기적으로 DC(직류)를 AC(교류)로 변환하는 역 변환 장치이며, 상용전원(AC 22V/440V)으로부터 공급된 전력을 입력받아 전압과 주파수를 가변시켜 전동기에 공급함으로써 전동기의 속도를 고효율로 이용하게 제어하는 장치이다. 본 논문에서는 550kW급 IGBT, DIODE의 발열에 의한 인버터 내부의 열 및 온도분포를 ICEPAK 상용코드를 통하여 수치적 해석을 수행하였다. 인버터의 발열은 캐패시터의 수명과 소자들의 오작동 등 많은 열적 문제를 가지고 있으며 Heat-sink, Fan, Duck등을 통하여 전도와 대류가 이루어지는 시스템이다. 인버터은 많은 파라미터들에 의해 온도가 결정되기 때문에 실험을 통한 해석은 제한적 일수 밖에 없다. 따라서 수치해석을 통하여 빠른 시간에 효율적인 열 설계를 할 수 있으며, 인버터의 크기는 최종적으로 Heat-sink의 형상에 따라 달라지므로 이를 최적화 하고 소형화 하는 작업이 필요하다. 인버터의 복잡한 내부구조상 하단부(발열원, Heat-sink, Fan등)만 수치해석을 수행하였을 때와 Full Model과는 $15^{\circ}C$ 온도 차이를 보였다. 최종적으로 인버터의 최적 열 설계를 위하여 Frame위치 변경, Heat-Sink 형상변화등 많은 수치해석을 통하여 만족할 만한 결과를 얻었다.

• The Journal of the Korea Contents Association
• /
• v.10 no.4
• /
• pp.257-264
• /
• 2010

Though existent a transcranial magnetic stimulation makes various treatment and diagnostic sine waveform of fixed stimulation pulse, there is limitation. In this research, because strength, pulse width, pulse pattern required in treatment and diagnostic introduce other Cockroft-Walton circuit and half bridge inverter frequency and voltage variable become new device propose wish to. Have more advantages than existing device. First, do not have high voltage transformer. Second, switching loss can be less, and control output energy precisely. Three, stimulation strengths, pulse width, pulse pattern are various. As a result, sought special quality and an experiment that is improved applying inverter and cockroft - Walton circuit is half bridge inverter that do not use transformer.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.7
• /
• pp.771-777
• /
• 2008

In this paper, a frequency doubler using modified time-delay technique is proposed. A voltage controlled delay line (VCDL) in the proposed frequency doubler compensates the group delay time mismatching between input and delayed signal. With the group delay time matching and waveform shaping using the adjustable Schmitt triggers, the unwanted fundamental component($f_0$) and the higher order harmonics such as third and fourth are diminished excellently. In result, only the doubled frequency component($2f_0$) appears dominantly at the output port. The frequency doubler is designed at 1.15 GHz of $f_0$ and fabricated with TSMC $0.18\;{\mu}m$ CMOS process. The measured output power at $2f_0$ is 2.67 dBm when the input power is 0 dBm. The obtained suppression ratio of $f_0,\;3f_0$, and $4f_0$ to $2f_0$ are 43.65, 38.65 and 35.59 dB, respectively.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.11
• /
• pp.130-137
• /
• 2013

This paper presents analog front-end(AFE) circuits for bio-potential measurement. The proposed AFE is composed of IA(instrument amplifier), BPF(band-pass filter), VGA(variable gain amplifier) and SAR(successive approximation register) type ADC. The low gm(LGM) circuits with current division technique and Miller capacitance with high gain amplifier enable IA to implement on-chip AC-coupling without external passive components. Spilt capacitor array with capacitor division technique and asynchronous control make the 12-b ADC with low power consumption and small die area. The total current consumption of proposed AFE is 6.3uA at 1.8V.

• The Journal of the Acoustical Society of Korea
• /
• v.41 no.5
• /
• pp.481-491
• /
• 2022

The active sonar transmission system consists of a transmitter that outputs an electrical signal and an underwater acoustic transducer that converts the amplified electrical signal into an acoustic signal. In general, the transmitter output characteristics are dependent on load impedance, and an underwater acoustic transducer, which is a transmitter load, has a characteristic that the electrical impedance varies largely according to frequency when driven. In such a variable impedance condition, the output of the active sonar transmission system may become unstable. Hence, this paper proposes a design and control technique of a sonar transmitter for transmitting a stable transmission signal even under variable impedance conditions of an underwater acoustic transducer in an active sonar transmission system. The electrical impedance characteristics of the underwater acoustic transducer are experimentally analyzed, and the sonar transmitter is composed of a single-phase full-bridge inverter, an LC filter, and a matching circuit. In this paper, the design and output control method of the sonar transmitter is proposed to protect the transmitter and transducer. It can secure stable output voltage characteristics even if it transmits the Linear Frequency Modulation (LFM) signal. The validity is verified through the simulation and the experiment.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.517-531
• /
• 1999

This paper presents the development of the 2-mode variable gain high power amplifier for a transmitter of INMARSAT-M operating at L-band(1626.5-1646.5 MHz). This SSPA(Solid State Power Amplifier) is amplified 42 dBm in high power mode and 36 dBm in low power mode for INMARSAT-M. The allowable error sets +1 dBm of an upper limit and -2 dBm of a lower limit, respectively. To simplify the fabrication process, the whole system is designed by two parts composed of a driving amplifier and a high power amplifier, The HP's MGA-64135 and Motorola's MRF-6401 are used for driving amplifier, and the ERICSSON's PTE-10114 and PTF-10021 are used the high power amplifier. The SSPA was fabricated by the circuits of RF, temperature compensation and 2-mode gain control circuit in aluminum housing. The gain control method was proposed by controlling the voltage for the 2-mode. In addition, It has been experimentally verified that the gain is controlled for single tone signal as well as two tone signals. The realized SSPA has 42 dB and 36 dB for small signal gain within 20 MHz bandwidth, and the VSWR of input and output port is less than 1.5:1 The minimum value of the 1 dB compression point gets 5 dBm for 2-mode variable gain high power amplifier. A typical two tone intermodulation point has 32.5 dBc maximum which is single carrier backed off 3 dB from 1 dB compression point. The maximum output power of 43 dBm was achieved at the 1636.5 MHz. These results reveal a high power of 20 Watt, which was the design target.the design target.