• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.1
• /
• pp.19-26
• /
• 1999

A moving-coil-type linear motor, designed and fabricated, is consisted of the NdFeB permanent magnets with high specific energy as the stator, a coil-wrapped nonmagnetic hollow rectangular structure and an iron core as a pathway for magnetic flux. The interaction between permanent magmet and armature fie1d, so called "push/pull effect", is to shift the airgap flux density variation due to the magnet alone by a certain amount. Thrust therefore is shift downward or upward. The push/pull effect was presented through the FEM analysis and the static tests. We compared the thrust obtained through the FEM analysis with the static tests. Finally, we present the linearity and correction coefficients of the thrust in consideration of the push/pull effects.l effects.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.4
• /
• pp.57-64
• /
• 2000

In this paper, to achieve the constant thrust force of the double side moving-magnet type LDM, the new armature winding of the LDM was proposed so as to restrain the saturation of the center yoke without increasing the mass of LDM. According to analyzing the magnetic flux distribution throughout the air-gap of the LDM, the magnet and winding width (1:0.84) was determined. The 2D finite element analysis was performed for force analysis on air-gap.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.196-199
• /
• 1998

LDM(Linear DC Motor) are used in high speed, high-precision position control system. Because of these advatages, LDM has already used in the motor of pen-recorder, magnetic-disk devices. Under the limited dimension, we propose the design method of LDM by magnetic circuit. In this paper, a relation between the thrust constant and size of a LDM that is moving coil type with unipolar is described, which is defined as a simple relational equation. To maximize the rate of thrust to the volume of LDM, the magnetic flux density in the yoke is adjusted to the value of magnetic equation. By the magnetic field analysis(FEM), the validity of the equation is confirmed.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.49 no.3
• /
• pp.180-187
• /
• 2000

A moving-coil-type linear oscillatory actuator(LOA) consists of the NdFeB permanent magnets with high specific energy as the stator, a coil-wrapped nonmagnetic hollow rectangular structure. The LOA system was represented by the voltage equation of coil and the mechanical equation of motion. This set of equations was manipulated in state-space form. The EMF constant kE of equation parameters in state-space form can be obtained by using the induced voltage in armature coils at open circuit test. kE and other parameters provide the system matrices and transfer function for frequency response and dynamic simulation. Voltage source inverter-fed LOA is examined aiming to compare with results of simulation.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2012.11a
• /
• pp.32-32
• /
• 2012

화석연료의 남용으로 지구 온난화가 심화되어 환경과 생태계변화가 가속화되고 있고, 급속한 산업의 발달과 인류 삶의 질 향상에 따른 에너지 수요가 급증하고 있는 실정에 있으며, 일본 후쿠시마 원전사태로 원자력 에너지의 위험성으로 지구 인류환경은 심각한 국면을 맞이 하고 있어 대체 에너지의 하나로 핵융합 에너지 필요성이 증대되고 있다. 핵융합 에너지 연구 개발은 우리나라에서 KSTAR가 1997년부터 건설하기 시작하여 지난 2007년에 완공되어 지금 운용 중에 있고, 국제적으로 미국, EU, 러시아, 중국, 한국, 일본 인도가 참여하는 ITER 국제 공동프로젝트가 2004년에 건설을 시작하여 프랑스 카다라쉬에 실증 플란트를 건설 중에 있다. 이러한 핵융합 반응을 위해서는 10e-7이상의 높은 진공과 1억$^{\circ}C$ 이상에서 중수소와 삼중수소가 반응하여 발생하는 플라즈마를 제어 할 필요가 있으며, 초고온의 핵융합 플라즈마를 가두고 가동시키기 위해서는 약 12Tesla이상의 고자장 마그넷이 필요하다. 현재 ITER 실증 플란트에 사용되는 고자장 마그넷은 TF (Toroidal Field)코일과 CS (Central Field)코일에 Nb3Sn 초전도선재가 핵심부품으로 사용되고 있으며 ITER프로젝트에서는 약 850톤의 Nb3Sn 초전도선재가 사용될 전망이다. 그 중에서 일본 25%, EU, 러시아와 한국이 각각 20%, 중국7%, 미국8% 할당되어 참여국 대부분은 초전도선재를 전략적으로 공급하고 있다. 초전도 선재의 크롬도금은 1~2 마이크로미터 이하의 균일하고 얇은 도금 두께와 밀착성이 우수한 품질이 요구된다. 일반적으로 크롬도금은 산업현장에서 컨베이어 벨트 방식으로 장식이나, 내식성 및 내마모성의 특성을 필요로 할 때 사용되고 있으나, 선재에 크롬도금을 릴투릴(Reel to Reel) 방식으로 적용되는 경우는 세계적으로 아주 드물다. 핵융합 마그넷의 CICC(Conduct In Cable Conduit)도체를 만들기 위해서는 초전도선재를 이용, 3(Sc 2+OFC 1)$^*3^*5^*5^*6$형태로 연선과 케이블링을 하게 되며, 초전도 선재를 연선하고 케이블링을 할 때 크롬 도금층이 박리될 가능성이 있어 크롬도금 방법과 프로세스를 특별히 고안할 필요가 있다. ITER핵융합로 마그넷의 TF코일은 높이 14m, 폭 9m 최대자장 12Tesla, 최대전류 68kA, CICC도체 직경이 40mm로서 그 초전도 조관/도체 내부에 0.82mm 직경의 Nb3Sn 초전도 선재가 약 1350가닥으로 연선과 케이블링으로 구성되어 있다. ITER 핵융합 마그넷용 초전도 선재의 크롬도금은 마그넷 권선 후 Nb3Sn 초전도물질을 형성하기 위해서 $650^{\circ}C$에서 500시간 열처리를 실시하며 열처리 시 초전도 선재의 소선들 사이에 발생할 수 있는 소착을 방지하고, 초전도 선재에서 발생하는 AC loss를 감소시키며, Quench시 발생되는 열을 쉽게 확산시킴으로써, 초전도 마그넷의 열적 안정성(Thermal Stability) 향상과 필요에 따라서 소선간 통전울 가능하게 한다. 고려제강의 자회사인 케이에이티는 크롬도금 밀착성이 우수하고 도금두께 0.1마이크로 미터 이내 제어가 가능한 얇고 균일한 도금품질을 개발하여 한국형 핵융합 실험로인 KSTAR에 65톤 전량 공급하였고, 크롬 도금된 무산소동 선재 32톤과 초전도 선재 93톤을 전량 ITER 프로젝트에 공급하고 있으며, 2013년도 상반기에는 공급을 마무리할 예정이다.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.5
• /
• pp.241-248
• /
• 1999

Recently, many linear motion generators and motors are rapidly finding applications that ranges from short stroke linear motion vibrators, such as dynamic cone type loudspeakers to stirling engine driven linear reciprocating alternators, compressors, textile machines etc. The stroke-length may go up to 2m, and the maximum speed is in the range of 5 to 10m/s with oscillating frequency as high as 15 kHz. Therefore, the linear oscillating actuators(LOAs) may be considered as variable speed drivers of precise controller with stoke-length and reversal periods during the reciprocating motion. In this paper, the design, fabrication, experiments, and extraction of control parameters of a moving coil type LOA for driving of linear reciprocating motion control systems, are treated. The actuator consists of the NdFeB permanent magnets with high specific energy as the stator produced magnetic field, a coil-wrapped nonmagnetic hollow rectangular bobbin structure, and an iron core as a pathway for magnetic flux. Actually, the design is accomplished by using FEM analysis for the basic configuration of a magnetic circuit, and characteristic equations for coil design. In order to apply as the drivers of a linear motion reciprocating control system, the control parameters and circuit parameters, such as input voltage-stoke, exciting frequency-stoke, coil inductance and so on, are extracted from the analysis and experiments on concerning a fabricating LOA.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.5
• /
• pp.5-21
• /
• 2015

An energy pile is a novel type of ground heat exchangers (GHEX's) which sets up heat exchange pipes inside a pile foundation, and allows to circulate a working fluid through the pipe for exchanging thermal energy with the surrounding ground stratum. Using existing foundation structure, the energy pile can function not only as a structural foundation but also as a GHEX. In this paper, six full-scale energy piles were constructed in a test bed with various configurations of the heat exchange pipe inside large-diameter cast-in-place piles, that is, three parallel U-type heat exchangers (5, 8 and 10 pairs), two coil type heat exchangers (with a 500 mm and 200 mm pitch), and one S-type heat exchanger. During constructing the energy piles, the constructability of each energy pile was evaluated with consideration of the installation time, the number of workers and any difficulty for installing. In order to evaluate the thermal performance of energy piles, the thermal performance tests were carried out by applying intermittent (8 hours operating-16 hours pause) artificial cooling operation to simulate a cooling load for commercial buildings. Through the thermal performance tests, the heat exchange rates of the six energy piles were evaluated in terms of the heat exchange amount normalized with the length of energy pile and/or the length of heat exchange pipe. Finally, the economic feasibility of energy pile was evaluated according to the various types of heat exchange pipe by calculating demanded expenses per 1 W/m based on the thermal performance test results along with the market value of heat exchange pipes and labor cost.

• Journal of Bio-Environment Control
• /
• v.17 no.2
• /
• pp.90-95
• /
• 2008

It has become a big matter of concerns that the skill and measures against reduction of energy and cost for heating a protected horticultural greenhouse were prepared. But in these days necessity of cooling a protected horticultural greenhouse is on the rise from partial high value added farm products. In this study, therefore, a horizontal type geothermal heat pump system with 10 RT scale to heat and cool a protected horticultural greenhouse and be considered to be cheaper than a vertical type geothermal heat pump system was installed in greenhouse with area of $240\;m^2$. And cooling performances of this system were analysed. As condenser outlet temperature of heat transfer medium fluid rose from $40^{\circ}C$ to $58^{\circ}C$, power consumption of the heat pump was an upturn from 11.5 kW to 15 kW and high pressure rose from 1,617 kPa to 2,450 kPa. Cooling COP had the trend that the higher the ground temperature at 1.75 m went, the lower the COP went. The COP was 2.7 at ground temperature at 1.75 m depth of $25.5^{\circ}C$ and 2.0 at the temperature of $33.5^{\circ}C$ and the heat extraction rate from the greenhouse were 28.8 kW, 26.5 kW respectively at the same ground temperature range. 8 hours after the heat pump was operated, the temperature of ground at 60 cm and 150 cm depth buried a geothermal heat exchanger rose $14.3^{\circ}C$, $15.3^{\circ}C$ respectively, but the temperature of ground at the same depth not buried rose $2.4^{\circ}C$, $4.3^{\circ}C$ respectively. The temperature of heat transfer medium fluid fell $7.5^{\circ}C$ after the fluid passed through geothermal heat exchanger and the fluid rejected average 46 kW to the 1.5 m depth ground. It analyzed the geothermal heat exchanger rejected average 36.8 W/m of the geothermal heat exchanger. Fan coil units in the greenhouse extracted average 28.2 kW from the greenhouse air and the temperature of heat transfer medium fluid rose $4.2^{\circ}C$after the fluid passing through fan coil units. It was analyzed the accumulation energy of thermal storage thank was 321 MJ in 3 hours and the rejection energy of the tank was 313 MJ in 4 hours.