• Applied Chemistry for Engineering
• /
• v.10 no.6
• /
• pp.852-856
• /
• 1999

The objective of this study was to prepare hydrogel beads which were useful microbial immobilization to remove nitrogen and phosphorous in the industrial wastewater. Two different polyols(PEG, PTMG) terminated with photo-crosslinkable methacrylate groups were synthesized. Structures of the prepolymers and the UV cured hydrogels were characterized by using $^1H$-NMR and FT-IR spectroscopy. Water content, mechanical strength and pore sizes of the hydrogels having different MW of polyols and different ratios of PEG/PTMG were investigated. Hydrogels prepared from PEG(MW1000) only or the mixture of PEG(MW1000) and PTMG(MW2900) with 7:3 by weight were considered as potential candidates for the matrix for the immobilization of microorganism.

• Applied Chemistry for Engineering
• /
• v.8 no.2
• /
• pp.197-203
• /
• 1997

The effect of additives on the mechanical properties of polyurethane foam were investigated. The resin used in this study was prepared by adding catalyst, surfactant and cross-linker to both KONIX FA-703 polyether polyol(80%) and KONIX FA-733 polyether polyol(20%). The polyurethane was foamed by adding equivalent amount of isocyanate(TDI-80, prepolymer M-200, pure MDI) to the resin and was used in property measurements after 72 hours hardening. The physical properties of polyurethane foam were investigated in terms of density, tensile strength, tear strength, elongation, sound absorption coefficient and gel profile measurements. The effects of surfactant on the cell size was investigated by scanning electron microscopy(SEM). The sound absorption coefficient was directly related to the cell size. The physical properties were improved with increasing amount of surfactant(L-5309) until 1.0 part per hundred polyol(1.0pphp).

• Membrane Journal
• /
• v.24 no.4
• /
• pp.292-300
• /
• 2014

Chlorine-resistant sulfonated poly(arylene ether sulfone) random copolymer (SPAES)-thin film composite (TFC) membranes for desalination are prepared using monoglyme as a selective solvent, which dissolves SPAES, but should be inert to porous polysulfone layer (e.g., Udel$^{(R)}$). Different from formic acid and diethylene glycol used as other selective solvents, monoglyme is environmentally friendly and has much lower boiling temperature. After a pretreatment of Udel$^{(R)}$ support film in isopropyl alcohol-glycerine mixture to minimize pore penetration leading to fairly reduced water flux, coating of SPAES solution in monoglyme onto the support and stepwise drying processes are conducted for defect-free TFC formation. The transport behavior through SPAES-TFC membranes is observed, correlating with the effects of sulfonation level, protonation, and physical and chemical crosslinking of SPAES selective layers.

• Polymer(Korea)
• /
• v.25 no.2
• /
• pp.177-185
• /
• 2001

In this work, the cure kinetics and rheological properties of difunctional epoxy(diglycidylether of bisphenol A, DGEBA)/polysulfone (PSF) blends were investigated using differential scanning calorimeter and rheometer. From the DSC results of the blends, the temperature of the exothermic peak and cure activation energy (E) using a half-width method were increased with increasing the PSF content to neat epoxy resin up to 30 wt%. However, a marginal decrease in the blend system was shown in E. The conversion ($\alpha$) and conversion rate (d$\alpha$/dt) were decreased as the content of PSF increases. Rheological properties of the blend system were investigated under isothermal condition using a rheometer. Cross-linking activation energy (E$_{c}$) was determined from the Arrhenius equation based on gel time and curing temperature. As a result, the E$_{c}$ showed a similar behavior with E which could be resulted from high viscosity of PSF and the phase separation between DGEBA and PSF.PSF.f PSF and the phase separation between DGEBA and PSF.PSF.

• Korean Journal of Materials Research
• /
• v.7 no.12
• /
• pp.1089-1096
• /
• 1997

본 연구에서는 에폭시/산무수물계에 화학양론비(r=산무수물/에폭시)를 0.5, 0.7,0.9,1.1로 변화시켜 서로 다른 두종류의 경화촉진제 1-cyanoethy1-2-ethy1-4-methy1 imidazole(2E4MZ-CN)과 N,N-dimethy1 benzy1 amine(BDMZ)을 첨가한 시료에 대한 경화거동과 경화 후 물성을 관찰하였다. 이 시료의 등온 경화거동은 동역학 측정기(dynamic mechanical analyzer, DMA)와 시차주사 열량분석기(differential scanning calorimeter, DSC)를 이용하여 조사하였다. DMA로부터 구해진 결과를 보면 경화시 상대저장강성을 (relative storage rigidity, RSR)과 상대손실강성율(relative loss rigidity, RSR)과 상대손실강성율(relative loss rigidity, RLR)의 변화가 r값과 경화촉진제의 종류에 영향을 받았다. 그리고 DSC결과는 r값이 감소함에 따라 경화가 촉진되는 것으로 나타났다. 경화물의 성질을 조사하기 위하여 사용된 DMA로부터 얻어진 유리전이온도(glass transition temperature, T$_{g}$)와 가교결합간의 평균분자량(average molecular weigh between crosslinks, M$_{c}$은 사용한 두 경화촉진제에 대하여 r값의 영향이 다르게 나타났다. BDMA의 경우는 T$_{g}$가 1:1화학양론비인 r=0.9에서 최고치를 보였으나, 2E4MZ-CN은 r이 감소함에 따라 계속 증가하는 양상을 보였다. 이와 같은 경향은 2E4MZ-CN을 경화촉진제로 사용하였을 때 에폭시가 과량으로 될수록 잔류 에폭시기들간의 에케르반응이 추가적으로 일어나 M$_{c}$가 감소하기 때문이다.

• Membrane Journal
• /
• v.20 no.4
• /
• pp.297-303
• /
• 2010

Composite membranes were prepared for membrane/cold condensation process for recovery of unreacted olefin monomer from the polyolefin polymerization process by solution coating and plasma polymerization processes. Poly(dimethylsiloxane) (PDMS) solution was coated on polysulfone (PSF) support and increase of prepolymer content in solution made more dense membrane structure to result in the increase of separation factor while absolute flux decreased. Permeation of organic materials through the composite membranes follows the sorption and diffusion mechanism, which brought about the results that separation factor increased with critical temperature of the organic materials, and that flux increased with the increase of the molar volume. Crosslinking period affected the permeation characteristics. Other types of composite membranes were fabricated by plasma polymerization of siloxane materials on polypropylene (PP) and PSF supports. PP was tested as a support for composite membranes, which had not been used so far in solution coating process, and plasma polymerization made the composite membranes equivalent performances to those of membranes prepared by solution coating process.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.350-357
• /
• 2000

Curing behaviors of glass/epoxy prepreg for printed circuit boards (PCB) were studied by using dielectrometer and differential scanning calorimeter. This prepreg was showed the lowest ionic viscosity at about 115$^{\circ}C$, and then the ionic viscosity was gradully increased up to 15$0^{\circ}C$. This indicated that the curing reaction of this prepreg started at 115$^{\circ}C$ and the molecular weight was increased by the accelerated thermal cross-linking reaction. The loss factor and tan $\delta$ values were also measured and discussed. The dielectric behaviors of this prepreg system were also measured according to the cure cycle for PCB. This material was found to be thermally stable up to about 30$0^{\circ}C$ and then was showed an abrupt decomposition beyond this temperature.

• Polymer(Korea)
• /
• v.31 no.2
• /
• pp.117-122
• /
• 2007

In this work, the mechanical and electrical properties, and thermal stability of vapor-grown carbon nanofibers/polyimide (VGCNFs/PI) composite film synthesized by in-situ polymerization were investigated in terms of tensile properties, volume resistivity and thermogravimetric analysis (TGA), respectively. From the results, the addition of VGCNFs with a certain amount into polyimide led to obvious improvement in tensile strength. The volume resistivity of the films was decreased with increasing the VGCNFs content and the electrical percolation threshold appeared between 1 and 3 wt% of VGCNFs content, which was probably caused by the formation of interconnective structures among the VGCNFs in a composite system. The thermal stability of the film was higher than that of pure PI one. This result indicated that the crosslinking of VGCNFs/PI Composites was enhanced by well-distribution of YGCNFs in PI resin, resulting in the increase of the thermal stability of the resulting composites.

• Korean Chemical Engineering Research
• /
• v.57 no.2
• /
• pp.232-238
• /
• 2019

Polyethylenimine-crosslinked chitin (PEI-chitin) was developed as a biosorbent to effectively remove dyestuffs from dye-containing wastewater. A representative reactive dye, Reactive Orange 16 (RO16) was used as a model dye. The effect of pH, isotherm, kinetic and desorption experiments were performed to evaluate the adsorption/desorption ability of PEI-chitin for RO16. As a result, the maximum adsorption capacity calculated by the Langmuir model was 266.3 mg/g at pH 2, and the time needed for adsorption equilibrium was evaluated to be about 20, 60, and 240 min for 50, 100, and 200 mg/L, respectively. The desorption experiments were carried out using various eluents such as ammonia/ethanol mixture, NaOH, $NaHCO_3$, and $Na_2CO_3$, and the highest desorption rate was 75.24% in the ammonia/ethanol mixture.

• Korean Chemical Engineering Research
• /
• v.55 no.3
• /
• pp.385-394
• /
• 2017

In this study, reaction mechanism and curing characteristics of adhesives formulated with NaOH- and $H_2SO_4$-hydrolyzed chicken feather (CF) and formaldehyde-based crosslinkers were investigated by FT-IR and DSC. In addition, adhesive properties and formaldehyde emission of medium-density fiberboards (MDF) applied with the adhesives were measured. CF-based adhesives having a solid content of 40% and over were very viscous at $25^{\circ}C$, but the viscosity reduced to $300{\sim}660m{\cdot}Pa{\cdot}s$ at $50^{\circ}C$. Consequently, the adhesives could be used as a sprayable resin. Through the FT-IR spectra of liquid and cured CF-based adhesives, addition reaction of methylol group and condensation reaction between the functional groups with the use of formaldehyde-based crosslinkers were identified. From the analysis of DSC, it was elucidated for CF-based adhesives to require a higher pressing temperature or longer pressing time comparing to commercial urea-formaldehyde (C-UF) resin. MDF bonded with CF-based adhesives, which was formulated with 5% NaOH-hydrolyzed CF (CF-AK-5%) and PF of formaldehyde to phenol mole ratio of 2.5 (PF-2.5), and pressed for 8 min had higher MOR and IB than those with other CF-based adhesives. MOR and IB of MDF bonded with the CF-based adhesives regardless of formulation type and pressing time were higher than those with C-UF resin. When the values compared with the minimum requirements of KS standard, IB exceeded the KS standard in all formulations and pressing time, but MOR of only MDF bonded with CF-AK-5% and PF-2.5 and pressed for 8 min satisfied the KS standard. What was worse, 24-TS of MDF bonded with all CF-based adhesives did not satisfied the KS standard. However, MOR and 24-TS can be improved by increasing the target density of MDF or the amount of wax emulsion, which is added to improve the water resistance of MDF. Importantly, the use of CF-based adhesives decreased greatly the formaldehyde emission. Based on the results, we reached the conclusion that CF-based adhesives formulated under proper conditions had a potential as a sprayable resin for the production of wood panels.