• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.283-283
• /
• 2015

현재 LAC 베어링에 적용되는 표면 처리는 일반적으로 하드터닝+슈퍼피니싱 가공이 적용되고 있고, 장수명을 위한 표면 처리 기술이 보다 더 요구되는 추세이다. Burnishing 기술은 매끄럽고 단단한 공구를 베어링 궤도면에 충분한 압력을 가하여 서로 문질러(rubbing) 마찰면을 소성 변형시켜 표면 거칠기 및 압축 잔류 응력 등을 향상 시키는 기술이며, 베어링과 같은 금속의 경우 버니싱 가공 적용 시 광택을 띠는 특성을 가지므로 외관 품질 향상에 기여하므로 슈퍼 피니싱 공정을 대신할 수 있다. 또한 표면 finishing, 표면 경도, 내마모성 및 피로/부식 저항성을 향상시킨다. 이에 본 연구에서는 슈퍼 피니싱 가공을 대신하기 위한 버니싱 가공의 물성을 검토하였고, 다른 공정과의 비교를 통한 버니싱 기술의 효과 확인하였다.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.11 no.8
• /
• pp.736-741
• /
• 2001

The restoration optimum image from transformation image demands compound change of image change, calender reform, and multiple solution calculation. This study presents that system actively deal with outside interference, vibration, movement, mechanical feature on the operating or before the operating and avoids complicated mathematical numerical expression and revise based on expert knowledge based which applies Fuzzy Logic which is one of Artificial Intelligent technique.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.6
• /
• pp.9-15
• /
• 2011

Any relative deformation between the cutting tool and the workpiece at machining point results directly in geometric and dimensional errors. The sources of relative deformations between the cutting tool and the workpiece at the contact point may be due to vibration, thermal deformation and cutting forces. In this paper, geometric error prediction of workpiece in turning has been investigated. To reach this goal, turning experiments are carried out according to selected cutting conditions. The variable cutting conditions are cutting speed, depth of cut and feed rate. The results will be useful as a guidance to select cutting conditions to improve the geometrical accuracy.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.10a
• /
• pp.223-226
• /
• 2009

The plastics are widely utilized in the inside of vehicles. The dynamic tensile characteristics of auto-body plastics are important in a prediction of deformation mode of the plastic component which undergoes the high speed deformation during car crash. This paper is concerned with the dynamic tensile characteristics of the auto-body plastics at intermediate strain rates. Quasi-static tensile tests were carried out at the strain rate ranged from 0.001/sec to 0.01/sec using the static tensile machine(Instron 5583). Dynamic tensile tests were carried out at the strain rate ranged from 0.1/sec to 100/sec using the high speed material testing machine developed. Conventional extensometry method is no longer available for plastics, since the deformation of plastic is accompanied with localized deformation. In this paper, quasi-static and dynamic tensile tests were performed using ASTM IV standard specimens with grids and images from a high speed camera were analyzed for strain measurement. True stress-strain relations and the actual strain rates at each deformation step were obtained by processing load data and deformation images, assuming the plastics to deform uniformly in each grid.

• Korean Journal of Optics and Photonics
• /
• v.13 no.1
• /
• pp.1-8
• /
• 2002

Optical payloads for earth-observation satellites become bigger as the required resolution becomes finer. For example, the diameter of the primary mirror of IKONOS, which has ground sampling distances of 1m/4m in panchromatic/multi spectral bands, is about 700mm. As the size of optical payload becomes bigger, the light-weighting of the mirrors becomes more significant. This paper presents the FEM results of the following four mirror types of 300 m diameter under gravity release and temperature changes: flat back mirror, single arch mirror, double arch mirror, and honeycomb sandwich mirror. Furthermore, this paper extends the FEM results to larger mirrors up to the diameter of 1m based on a general scaling law and Valenete\`s equation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.380-388
• /
• 2016

Commercially pure titanium (CP Ti) has been actively used in plate heat exchangers due to its light weight, high specific strength, and excellent corrosion resistance. However, compared with automotive steels and aluminum alloys, there has not been much research on the plastic deformation characteristics and press formability of CP Ti sheet. In this study, the mechanical properties of CP Ti sheet are clarified in relation to press formability, including anisotropic properties and the stress-strain relation. The flow curve of the true stress-true strain relation is fitted well by the Kim-Tuan hardening equation rather than the Voce and Swift models. The forming limit curve (FLC) of CP Ti sheet was experimentally evaluated as a criterion for press formability by punch stretching tests. Analytical predictions were also made via Hora's modified maximum force criterion. The predicted FLC with the Kim-Tuan hardening model and an appropriate yield function shows good correlation with the experimental results of the punch stretching test.

• Journal of the Korea Convergence Society
• /
• v.10 no.12
• /
• pp.287-292
• /
• 2019

This paper analyzes the thermal behaviors of genuine discs used in automobiles and discs coming out of tuning products through FEM analysis. Modeling with genuine disk modeling and tuning disks Model-1, Model-2, Model-3 and analyzing the disk rotation speed was set to 1000rpm. When the brake is operated, the thermal behavior of the disk surface, such as the operating temperature caused by the disk and pad contact, the friction surface temperature after the disk stop, and the thermal deformation, were analyzed. When the brake was activated (0-4.5 seconds), the tuning disk showed 34℃ higher than the original disk, and after the disk stopped (40.5 seconds), the tuning disk was analyzed 18℃ lowe, deformation due to the disk heat was deformed by 0.3mm for the tuning disk. Although there is an effect to reduce the fading phenomenon due to the thermal behavior of the pure disk and the tuning disk, it can be observed that there is no significant change in the thermal behavior due to the hole processing and the disk surface processing of the tuning disk.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.9
• /
• pp.1227-1233
• /
• 2010

In the hot section of a gas turbine, the turbine blades were protected from high temperature by providing a thermal barrier coating (TBC) as well as by cooling air flowing through internal passages within the blades. The cooling air then passed through discrete holes on the blade surface, creating a film of cooling air that further protects the surface from the hot mainstream flow. The holes are subjected to stresses resulting from the lateral growth of thermally grown oxide, the thermal expansion misfit between the constituent layers, and the centrifugal force due to high-speed revolution; these stresses often result in cracking. In this study, the deformation and cracks occurring near a hole on a heat-resistant alloy subjected to thermo-mechanical cycling were investigated. The experiment showed that cracks formed around the hole depending on the applied stress level and the number of cycles. These results could be explained by our analytic solution.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.114-114
• /
• 2009

최근 국내외에서 자동차 연비와 성능 향상을 위하여 고부가가치 자동변속기의 개발이 적극적으로 추진되고 있다. 특히, 유럽(ZF)과 일본(JATCO, AISIN)을 비롯한 변속기 부품의 기술선진국에서는 전자빔 용접을 적용한 고부가가치 자동변속기 제품이 개발되어 다양한 고급차 모델에 적용되고 있으며 2010년까지 8속 자동변속기를 출시할 예정으로 개발을 추진하고 있다. 이러한 자동변속기를 개발하기 위하여 부품의 성형 및 가공정밀도 관리가 중요하며, 최종 조립되는 부품의 전처리(연질화처리, 탈지, 이물질 제거등)와 용접시 용접변형을 최소화하기 위한 공정조건의 엄격한 관리가 요구되고 있다. 변속기 부품으로 사용되는 소재는 성형성 확보를 위한 연질재(SPCC)와 강도를 확보하기 위한 고강도강(SAPH400, SPFH590)으로 서로 다른 두께의 재질이 조립되어 최종단계에서 용접공정에 의해 제작되고 있다. 특히, 연질재는 복잡한 형상으로 성형한 다음, 가공을 거쳐 경화를 위한 연질화처리가 요구되기 때문에 건전한 용접을 하기 위해서는 용접면에 접한 연질화 처리부는 연질화 처리재가 잔존하지 않도록 완전한 제거할 필요가 있다. 만약 전처리 공정에서 충분한 세척과 가공품의 정도관리가 확보되지 않으면 전자빔 용접시 고온에서 이물질 증발과 잔류, 스패터 발생등에 의한 용접부 결함발생이나 용접변형으로 인하여 제품불량이 발생하게 된다. 따라서 본 연구에서는 최종 조립공정인 용접작업시 발생되는 결함을 방지하고 이 두께 및 이종소재의 전자빔 용접비드 형상(비드 폭, 용입깊이)을 최적화 함으로서 용접부 변형을 최소화하고 충분한 강도를 확보하고자 전자빔 용접전류와 속도에 따른 비드형상을 비교검토 하고자 하였다. 그리고 실차적용시 신뢰성을 확보하기 위하여 전자빔 용접한 자동차 변속기 부품의 비틀림 시험을 실시하였으며 전자빔 용접 전, 후의 변형량을 측정하여 변속기 부품으로서의 적용성을 검증하고자 하였다.

• Transactions of Materials Processing
• /
• v.28 no.3
• /
• pp.135-144
• /
• 2019

Electromagnetic impulse welding (EMIW) is a type of solid state welding using the Lorentz force generated by interaction between the magnetic field of the coil and the current induced in the workpiece. Although many experimental studies have been investigated on the expansion and compression welding of tube using the EMIW process, studies on the EMIW process of lap joint between flat sheets are uncommon. Since the magnetic field enveloped inside the tube can be controlled with ease, the electromagnetic technique has been widely used for tube welding. Conversely, it is difficult to control the magnetic field in the flat sheet welding so as to obtain the required welding velocity. The current study analyzed the effects of coil shape on the impulse velocity for suitable flat one-turn coil for the EMIW of the flat sheets. The finite element (FE) multi-physics simulation involving magnetic and structural field of EMIW were conducted with the commercial software LS-DYNA to evaluate the several shape variables, viz., influence of various widths, thicknesses, gaps and standoff distances of the flat one-turn coil on the impulse velocity. To obtain maximum impulse velocity, the flat one-turn coil was designed based on the FE simulation results. The experiments were performed using an aluminum alloy 1050 sheets of 1.0mm thickness using the designed flat one-turn coil. Through the microscopic interfacial analysis of the welded specimens, the interfacial connectivity was observed to have no defects. In addition, the single lap joint tests were performed to evaluate the welding strength, and a fracture occurred in the base material. As a result, a flat one-turn coil was successfully designed to guarantee welding with bond strength equal to or greater than the base material strength.