• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.15 no.3
• /
• pp.207-210
• /
• 1982

For the removal of initial water content in cuttlefish, the effects of fixed-bed drying condition on the drying rate were investigated, with following results. 1. The drying rate of cuttlefish dried at fixed-bed condition was also faster than that at natural convection type or hot air dryer.2. By controlling air temperature and its direction to cut-and-peeled sample the drying time can be reduced to 2 hrs. 3. Shirai's equation and Arrhenius' law were applicable to fixed-bed dried cuttlefish. Drying rate constant (k) by Shirai's equation, and Arrhenius' plot were as shown in Table 3, 4 and Fig.3, respectively.

• Korean Journal of Human Ecology
• /
• v.15 no.3
• /
• pp.439-447
• /
• 2006

The purpose of this study is to explore the accuracy and reliability of subjective evaluation instruments in evaluating sensibility of similar fabrics, Kendall's coefficient of concordance W (agreement among subjects) and Spearman rank correlation coefficient (reproducibility after 1 week) were used to evaluate which one is more efficient. Eight kinds of linen-like silk fabrics finished with polyurethane resin were used, Subjective evaluation instruments such as rating scale method, contrasting method against a control, rank ordering method, paired comparison and Quad analysis were used, 'Stiffness and Pliability' and 'Preference of summer fabric' were estimated, From the result of subjective stiffness and pliability, which are effective on objective properties of fabric, the rating scale method in Kendall's coefficient of concordance W and Quad analysis in Spearman rank correlation coefficient were given the highest score, From the result of subjective preference of summer fabric, which are effective on individual sensibility, contrasting method against a control in Kendall's coefficient of concordance W and Quad analysis in Spearman rank correlation coefficient revealed the highest score, Regarding the accuracy, reliability and efficiency, Quad analysis was an efficient method for subjective evaluation of linen-like silk fabrics.

• KSBB Journal
• /
• v.23 no.2
• /
• pp.131-134
• /
• 2008

Tea seed extract, a byproduct of tea processing, contains two kaempferol glycosides, camelliaside A and camelliaside B. Kaempferol was produced by enzymatic hydrolysis of glycosides. Optimum reaction conditions were investigated. $Pectinex^{(R)}100L$ was effective, producing kaempferol in 48 hrs. Optimum temperature and pH were $40^{\circ}C$ and 4, respectively. Ratio of substrate and enzyme affected the yield. Under optimum conditions, 1.6g kaempferol per 1 kg tea seed extract was produced and 80% of kaempferol precipitated. This result shows that kaempferol could be produced mildly and effectively using tea-processing byproduct.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.239-240
• /
• 2006

For longer than picosecond pulses, bulk damage inside defect-free dielectrics involves the heating and multiplication of spurious electrons by the incident laser beam and transfer of this energy to the lattice. The situation is quite different for femtosecond pulses which are shorter than the time scale for electron energy transfer to the lattice. Damage caused by these pulses is produced with smaller statistical uncertainty and is controllable on a microscopic scale. These properties can be exploited to produce laser devices such as arrays of damage dots for all optical memories with high data storage density or arrays of parallel grooves to form transmission gratings. In this work, we observed characteristic of the femtosecond laser machining in BK7 and fused silica.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.10
• /
• pp.101-108
• /
• 2001

In this study, the static and dynamic characteristics of endmilling process were modelled and the analytic realization of chatter mechanism was discussed. In this reward, We have discussed on the comparative assessment of recursive time series modeling algorithms that cal represent time machining process and detect the abnormal machining behaviors in precision endmilling operation. In this study, simulation and experimental works were performed to show the malfunctional behaviors. For this purpose, new recursive algorithm(RLSM) was adopted for the oil-line system identification and monitoring of a machining process, we can apply these new algorithms in real process for detection of abnormal chatter. Also, The stability lobe of chatter was analysed by varying parameter of cutting dynamics in regenerative chatter mechanics.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.20 no.2
• /
• pp.162-168
• /
• 2011

In this research, nitrogen plasma source ion implantation(PSII) of non-coated tungsten carbide endmill tools was conducted with low heat treatment for increasing wear resistance. After the low heat treatment of PSIIed tools to give a homogeneity of wear resistance, the surface modification of tools was analyzed by hardness test, surface roughness and cutting forces. As for the resultant cutting forces, low heat treatment in temperature of $400^{\circ}C$ and $500^{\circ}C$ is stable because of low cutting resistance. The 20-minutes heat treated tool at spindle speed 25000rpm has superiority of surface roughness, Ra of $0.420{\mu}m$ and was found to have good wear resistance. The higher hardness value was obtained by increasing temperature from $300^{\circ}C$ to $600^{\circ}C$ for PSIIed tools with low heat treatment. As the PSIIed tools under 10minutes at temperature of $600^{\circ}C$ have the highest hardness as Hv of 2349.8, It was analyzed that temperature processing give much influences on hardness.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.11
• /
• pp.990-996
• /
• 2008

Nowadays, the trend to a lightweight design accelerates the use of advanced high strength steel (AHSS) in automotive industry. Springback phenomena is a hot issue in the sheet metal forming, especially bending process using AHSS. Several analytical methods for that have been proposed in recent years. Each of method has their advantages and disadvantages. There are only a few optimal solutions which can minimize the two objectives simultaneously. In this study, an effective method optimized the multi objective value. The method by the design of experiments(DOE) and artificial neural network(ANN) was presented to compensate springback of bending parts. This method was applied to L and V bending process. The effective method could be optimized to multiple object. It was confirmed that the proposed method was more efficient than traditional manual FEA procedure and the trial and error approach for springback compensation.

• Journal of the Korean Society of Industry Convergence
• /
• v.8 no.1
• /
• pp.31-36
• /
• 2005

The purpose of this experimental study is to gain equations for the prediction of surface roughness depending on the three major parameters(the cutting speed, the feed rate and the nose radius). It is the merit of Response Surface Methodology that the test time is reduced to minimum size and accurate analysis can be done. On this study, first, made specimen, Al 5052 BE material which is widely used in school and cut the specimen with coated tungsten carbide tools, by varying the cutting conditions, such as the cutting speed, the feed rate and the nose radius. In conclusion, the surface roughness was most greatly influenced by the feed rate. And Surface Roughness equation gained by experiment is as followed $$R=58.2\;v^{-0.22}f^{1.7}r^{-0.66}$$.

• Journal of the Society of Naval Architects of Korea
• /
• v.34 no.3
• /
• pp.104-112
• /
• 1997

Line heating process has been used in forming hull surfaces long before and it has depended on skillful workers. As the reduction of production cost is major concern of shipbuilding companies, line heating work must be improved for higher productivity. In this paper, as the first step to automatic hull forming, a method is proposed to predict deformations due to line heating. It includes a simplified thermal elasto-plastic analysis to increase computing efficiency and to do real time visualization of deformed shapes. For the prediction of deformation, a method to estimate heat flux of the torch is also introduced. Predicted deformations for line heated plates show good agreement with experimental results. The proposed method can be used in control and simulation of line heating process with ease.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.5 s.182
• /
• pp.51-58
• /
• 2006

The necessities for heightening fuel efficiency as well as lightweight design, lead to an increase of the use of aluminum alloys in the automobile industry. Extruded aluminum profile channels are used widely for the design of frame parts as lightweight assemblies, especially if a high stiffness is needed. While many applications can be realized with forming of hollow square-sectioned extruded profiles such as a stretch bending and a hydro-forming, some applications demand the use of a press bending which can be hardly found in the previous study. In this study, by introducing the use of a press bending into car sub-frames, the demands for higher accuracy as well as higher flexible method than the conventional methods will be satisfied. With respect to the design of sub-frames, the process planning was performed from the shape of a sub-frame product. The designed processes were analyzed by the commercial FEM code, DEFORM-3D. Forming dies for the each process were designed and prototypes of sub-frames were manufactured by the verified farming process. In addition, some of the important features of design parameters in the press bending were reviewed.