• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.780-785
• /
• 2016

Heavy oil used as ship propulsion has a serious issue regarding exhaust emission of global warming. Recently, among large-scale merchant ships are using LNG as green ships so called ech-ships. In this study, an vaporizer and pipes under cryogenic and high pressure load were considered to evaluate structural integrity according to codes. Structural analysis of the vaporizer and pipes was performed using the commercial code, ANSYS. Integrity evaluation of the vaporizer based on von Mises stress was performed in accordance with allowable stress specified in ASME Boiler & Pressure Vesssel Section VIII Division 2. To assess structural integrity of the pipes, stress components were combined and compared with ASME B31.3. The calculated stresses for all load cases are lower than allowable stresses, therefore the structural integrity of equipments are verified.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.12 no.2
• /
• pp.35-42
• /
• 1975

This paper investigates the distribution of stress and its behavior at the Root Toe in fillet welding joint. Furthermore, the stress components and principal stresses in the fillet welds are calculated by the finite element method. The distribution of stresses obtained numerically by means of the finite element method is also compared with the experimental results of two dimensional photoelasticity. A Cover plate type and Center block type of fillet welds are used as models for the numerical calculations covering the variations of 2 W/M(thickness of main plate/thickness of cover plate)=1 through 2W/M=4. The results obtained in these studies are summarized as follows; 1) When W2/M values become small, the stress concentration factors of the Root are larger than of the Toe in a C-type. Its critical value is 2W/M=3.00. However, no critical value exists in a T-type. 2) For 2W/M Values being avove 3.5 in a C-type and above 4.0 in a T-type, $K_R$ and $K_{\tau}$ become 1. 3) According to the differences of 2W/M values, the differences in stress become increasing in the Root but become decreasing in the Toe. These differences, however, disappear as the free boundary surface is approached. 4) The stress concentration factors of both the Root and Toe obtained by means of the finite element method have somewhat lower values than obtained by the photoelasiticity. But their principal stress directions coincide in either method. 5) It proves beneficial to employ the finite element method for two-dimensional plane stress analysis in front fillet welding joint.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.9
• /
• pp.640-646
• /
• 2007

The cooling heat transfer coefficient of $CO_2$ (R-744) for tube and coil diameter (CD), inclined angle of tube and coil pitch of inclined helical coil type copper tubes were investigated experimentally. The main components of the refrigerant loop are a receiver, a variable-speed pump, a mass flow meter, a pre-heater and a inclined helical coil type gas cooler (test section). The test section consists of a smooth copper tube of 2.45 and 4.55 mm inner diameter (ID). The refrigerant mass flukes were varied from 200 to 800 [$kg/m^2s$] and the inlet pressures of gas cooler were 7.5 to 10.0 [MPa]. The heat transfer coefficients of $CO_2$ in inclined helical coil tube with 2.45 mm ID are $5{\sim}10.3%$ higher than those of 4.55 mm. The heat transfer coefficients of 41.35 mm CD are $8{\sim}32.4%$ higher than those of 26.75 mm CD. Comparison between $45^{\circ}\;and\;90^{\circ}$ of coil angle, the heat transfer coefficients of $45^{\circ}$ are higher than those of $90^{\circ}$. For coil pitch of gas cooler, the heat transfer coefficients of inclined helical coil gas cooler with coil pitch of 5 mm are similar to those of 10 and 15 mm.

• International Journal of Fluid Machinery and Systems
• /
• v.3 no.1
• /
• pp.11-19
• /
• 2010

The performance of the crossover system of a centrifugal compressor stage consisting of static components of $180^{\circ}$ U-bend, return channel vanes and exit ducting with a $90^{\circ}$ bend is investigated. This study is confined to the assessment of performance of the crossover system by varying the shape of the return channel vanes. For this purpose two different types of Return Channel Vanes (RCV1 and RCV2) were experimentally investigated. The performance of the crossover system is discussed in terms of total pressure loss coefficient, static pressure recovery coefficient and vane surface pressure distribution. The experimentation was carried out on a test setup in which static swirl vanes were used to simulate the flow at the exit of an actual centrifugal compressor impeller with a design flow coefficient of 0.053. The swirl vanes are connected to a mechanism with which the flow angle at the inlet of U-bend could be altered. The measurements were taken at five different operating conditions varying from 70% to 120% of design flow rate. On an overall assessment RCV1 is found to give better performance in comparison to RCV2 for different U-bend inlet flow angles. The performance of RCV2 was verified using numerical studies with the help of a CFD Code. Three dimensional sector models were used for simulating the flow through the crossover system. The turbulence was predicted with standard k-$\varepsilon$, 2-equation model. The iso-Mach contour plots on different planes and development of secondary flows were visualized through this study.

• Journal of the Korean Society of Tobacco Science
• /
• v.29 no.1
• /
• pp.30-40
• /
• 2007

The objective of this study was to investigate the contribution of various smoke constituents to the toxicological activity of total particulate matter(TPM) or the gas/vapor phase(GVP). These components included phenol compounds, aromatic amines, polycyclic aromatic hydrocarbons, heterocyclic amines, and carbonyl compounds. The mutagenic and cytotoxic potencies were assessed using the Salmonella mutagenicity assay with S. typimurium TA98 strain and the neutral red uptake cytotoxicity assay(NRU) with BALB/c 3T3 fibroblast cells, respectively. The Salmonella mutagenicity test showed that heterocyclic amines exhibited significantly higher levels of toxicity compared to other smoke constituents. Among them, 2-amino-3,4-dimethylimidazo[4,5-f]quinoline(MeIQ) was shown the most mutagenic compound with a specific mutagenicity of $7.9{\times}10^5\;revertants/{\mu}g$. An analysis of the possible contribution revealed that MeIQ account for only 0.85% of the 2R4F-TPM mutagenicity in TA98. NRU data demonstrated that high cytotoxic activity was obtained for hydroquinone, formaldehyde, and acrolein. Based on the results of the present study, the contribution of acrolein to the cytotoxicity of the GVP fraction was calculated as 61%. Thus, a large proportion of the cytotoxic activity of this complex mixture, cigarette smoke gas phase, can be attributed to the acrolein.

• Journal of Ginseng Research
• /
• v.37 no.4
• /
• pp.475-482
• /
• 2013

The main active components of Panax ginseng are ginsenosides. Ginsenoside Rb1 and Rg1 are accepted as marker substances for quality control worldwide. The analytical methods currently used to detect these two compounds unfairly penalize steamed and dried (red) P. ginseng preparations, because it has a lower content of those ginsenosides than white ginseng. To manufacture red ginseng products from fresh ginseng, the ginseng roots are exposed to high temperatures for many hours. This heating process converts the naturally occurring ginsenoside Rb1 and Rg1 into artifact ginsenosides such as ginsenoside Rg3, Rg5, Rh1, and Rh2, among others. This study highlights the absurdity of the current analytical practice by investigating the time-dependent changes in the crude saponin and the major natural and artifact ginsenosides contents during simmering. The results lead us to recommend (20S)- and (20R)-ginsenoside Rg3 as new reference materials to complement the current P. ginseng preparation reference materials ginsenoside Rb1 and Rg1. An attempt has also been made to establish validated qualitative and quantitative analytical procedures for these four compounds that meet International Conference of Harmonization (ICH) guidelines for specificity, linearity, range, accuracy, precision, detection limit, quantitation limit, robustness and system suitability. Based on these results, we suggest a validated analytical procedure which conforms to ICH guidelines and equally values the contents of ginsenosides in white and red ginseng preparations.

• Journal of Plant Biotechnology
• /
• v.48 no.4
• /
• pp.278-288
• /
• 2021

The development of bioenergy through biomass has gained importance due to the increasing rates of fossil fuel depletion. Biomass is important to increase the productivity of bioethanol, and production of biomass with high biomass productivity, low lignin content, and high cellulose content is also important in this regard. Inorganic salts are important in the cultivation of biomass crops for the production of biomass with desirable characteristics. In this study, the roles of various inorganic salts in biomass and bioethanol production were investigated using an in vitro tobacco culture system. The inorganic salts evaluated in this study showed dramatic effects on tobacco plant growth. For example, H₂PO₄ substantially improved plant growth and the root/shoot (R/S) ratio. The chemical compositions of tobacco plants grown in media after removal of various inorganic salts also showed significant differences; for example, lignin content was high after Mg²⁺ removal treatment and low after K⁺ treatment and H₂PO₄ removal treatment. On the other hand, NO₃^- and H₂PO₄ treatments yielded the highest cellulose content, while enzymatic hydrolysis yielded the highest glucose concentration ratio 24 h after NH₄⁺ removal treatment. The ethanol productivity after H₂PO₄ removal treatment was 3.95% (w/v) 24 h after fermentation and 3.75% (w/v) after 36 h. These results can be used as the basis for producing high-quality biomass for future bioethanol production.

• Earthquakes and Structures
• /
• v.20 no.4
• /
• pp.377-388
• /
• 2021

Thin perforated Steel Plate Shear Walls (SPSWs) are among the most common types of seismic energy dissipation systems to protect the main boundary components of SPSWs from fatal fractures in the high-risk zones. In this paper, the cyclic behavior of the different circular hole patterns under cyclic loading is reported. Based on the experimental results, it can be concluded that a change in the perforation pattern of the circular holes leads to a change in the locations of the fracture tendency over the web plate, especially at the plate-frame interactions. Accordingly, the cyclic responses of the tested specimens were simulated by finite element method using the ABAQUS package. Likewise, perforated shear panels with a new perforation pattern obtained by implementing Topology Optimization (TO) were proposed. It was found that the ultimate shear strength of the specimen with the proposed TO perforation pattern was higher than that of the other specimens. In addition, theoretical equations using the Plate-Frame Interaction (PFI) method were used to predict the shear strength and initial stiffness of the considered specimens. The theoretical results showed that the proposed reduced coefficients relationships cannot accurately predict the shear strength and initial stiffness of the considered perforated shear panels. Therefore, the reduced coefficients should be adopted in the theoretical equations based on the obtained experimental and numerical results. Finally, with the results of this study, the shear strength and initial stiffness of these types of perforated shear panels can be predicted by PFI method.

• Horticulture, Environment, and Biotechnology : HEB
• /
• v.59 no.6
• /
• pp.815-826
• /
• 2018

The intense drought affecting olive production in Northern Chile underscores the need to research non-traditional irrigation strategies to obtain the best crop performance. Accordingly, this study aimed to obtain preliminary data to guide future research on this topic. Different water replenishment levels on crop evapotranspiration ($ET_c$ ; 13.5, 27.0, 40.5, and 54%) were established in a young orchard, cv. Arbequina, from the end of fruit drop (EFD) to full bloom in the next season. We evaluated the influence of plant water status (${\Psi}_{stem}$ ) and crop load, considered as function of fruit number divided by trunk cross-sectional area, on reproductive and productive variables using multiple linear regressions. Our results show that crop load and ${\Psi}_{stem}$ measured from EFD to harvest affected yield components. Nevertheless, ${\Psi}_{stem}$ had the strongest influence on fruit size, pulp development, oil accumulation, and yield. Oil content and yield were reduced by 54% and 50% for each MPa, respectively, from ${\Psi}_{stem\;EFD-H}$ -1.8 MPa, an effect that intensified as crop load increased. During the period of flower development (September-November), the number of flowers per inflorescence and percentage of perfect flowers were reduced when ${\Psi}_{stem}$ was less than -2.0 MPa. These preliminary results showed that bud differentiation, inflorescence and flower formation are highly sensitive to water deficit.

• Journal of Korean Elementary Science Education
• /
• v.38 no.4
• /
• pp.439-452
• /
• 2019

This study aims to compare self- and peer-assessments of science-gifted elementary students' scientific creativity. A science-gifted program on the Pascal's principle was implemented to 40 fifth-graders in the Science-Gifted Education Center for two weeks. After that, students presented their results from a scientific creativity task using the principle in class. The task was to devise a new and useful tool using the principle, and it included the students' self-assessment about their idea. During presentation, students were asked to assess the works of peers and write down the reasons that they gave the scores they gave. Shortly, student self- and peer-assessments about students' scientific creativity outcomes were compared. Based on two essential components of creativity, ideas that satisfy both originality and usefulness can be counted as scientifically creative. The main results of this study are as follows: First, the average scores of student self- and peer-assessments were 71.5 and 61.9. Second, the standard deviations of student self- and peer-assessments were 14.47 and 5.79. Third, among scientific creativity, originality, usefulness scores, only originality had a significant correlation between student self- and peer-assessment (r=.42). Fourth, the students were categorized into four groups according to the levels of their scores by student self- and peer-assessment. And the frequencies of peer-assessment group had a significant difference at p<0.05 level, according to self-assessment group (Chi Square=4.0000, df=1, p=0.0455). Fifth, through a case study by group, the results suggesting that self-assessment could be affected by the students' self-efficacy and perfectionism and such effect could also influence peer-assessment have been found. The result showed that how the student self- and peer-assessment of scientific creativity are different and what the students' thoughts on the evaluation of scientific creativity are. The findings suggested that there are several things to consider for the educators to make efforts to construct consistent assessment methods for scientific creativity.