• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1550-1552
• /
• 1999

In this study, (Ba,Sr)$TiO_3$ thin films were etched with a magnetically enhanced inductively coupled plasma (MEICP) as a function $CF_4$/Ar gas mixing ratio. Experimental was done by varying the etching parameters such as rf power, dc bias and chamber pressure. The maximum etch rate of the BST films was $1700{\AA}$/min under $CF_4/(CF_4+Ar)$ of 0.1, 600W/350V and 5 mTorr. The selectivity of BST to Pt and PR was 0.6, 0.7, respectively. X-ray photoelectron spectroscopy (XPS) studies shows that there are surface reaction between Ba, Sr, Ti and C, F radicals during the (Ba,Sr)$TiO_3$ etching. To analysis the composition of surface residue remaining after the etching, films etched with different $CF_4$/Ar gas mixing ratio were investigated using XPS.

• 한국재료학회지
• /
• 제17권7호
• /
• pp.386-389
• /
• 2007

The dielectric properties of $(Ba_{0.5}Sr_{0.5})TiO_3$ ferroelectric thin films have been investigated according to the substrates in order to optimize the their properties. MgO, r-plane sapphire, and poly-crystalline sapphire (Alumina) substrates have been used to deposite $(Ba_{0.5}Sr_{0.5})TiO_3$ ferroelectric thin films by RF magnetron sputtering. The BST thin films deposited on the single crystal (100)MgO substrates have high tunability and low dielectric loss. These results are caused by a low misfit between the lattice parameters of the BST films and the substrate. The BST films deposited on r-plane sapphire have relatively high misfit, and the tunability of 17% and dielectric loss of 0.0007. To improve the dielectric properties of the BST films, the post-annealing methods has been introduced. The BST films deposited on (100)MgO, (1102)r-plane sapphire, and poly-crystalline sapphire substrates have best properties in post-annealing conditions of $1050^{\circ}C$, $1100^{\circ}C$, and $1150^{\circ}C$, respectively. The different optimal post-annealing conditions have been found according to the different misfits between the films and substrates, and thermal expansion coefficients. Moreover, the films deposited on alumina substrate which is relatively cheap have a good tunability properties of 23% by the post-annealing.

• 한국진공학회지
• /
• 제11권1호
• /
• pp.1-7
• /
• 2002

RF Magnetron Sputtering 방법으로 $Ba_{0.5}Sr_{0.5}TiO_3$ 박막을 Pt/Ti/$SiO_2$/Si 기판위에 증착하였다. $Ba_{0.5}Sr_{0.5}TiO_3$ 박막 증착시 기판온도는 실온으로 고정시켜주었고, 작업 가스 유량(Ar:$O_2$)과 RF Power는 각각 90:10에서 60:40까지 그리고 50 W와 75 W로 하였다. 또한 박막 증착 후 RTA(Rapid Thermal Annealing)를 이용하여 산소분위기에서 $600^{\circ}C$로 고온 순간 열처리를 하였다. 커패시터 제작을 위해 UHV System의 E-beam evaporator를 이용하여 Pt를 증착하였다. XRD 측정을 통한 구조적 특성에서는 작업 가스 유량과 RF Power에 비해 고온 순간 열처리가 결정화에 기여도가 큼을 확인할 수 있었다. 전기적 특성에서는 RF Power가 50 W이고 열처리를 한 샘플에서 비교적 우수한 특성을 보여주었다.

• 한국결정성장학회지
• /
• 제8권3호
• /
• pp.407-410
• /
• 1998

$RuO_2$를 하부전극으로 적용한 (Ba,Sr)$TiO_3$[BST] 박막의 Sputtering 가스내 $O_2/Ar$ 비에 따른 특성을 고찰하였다. $O_2/Ar$ 비가 1/9에서 5/5로 증가함에 따라 BST 박막의 유전상수는 135에서 190로 증가한 반면, 누설전류 특성은 $1.9{\times}10^{-7}\; A/{\textrm}{cm}^2$에서 $1.7{\times}10^{-6}; A/{\textrm}{cm}^2$로 저하되었다. $O_2/Ar$ 비 증가에 따른 BST 박막의 결정성의 향상에도 불구하고 BST 박막의 표면거칠기의 증가와 BST/ $RuO_2$계면에서의 산소결핍 지역의 확장 등이 BST 박막의 누설전류 특성의 저하를 초래하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 반도체 재료 센서 박막재료 전자세라믹스
• /
• pp.157-160
• /
• 2004

Ferroelectric $(Ba_xSr_{1-x})TiO_3$ (BST) thin films have been deposited on (001) MgO single crystals by a pulsed laser deposition (PLD) method. The structure of deposited BST thin films were investigated by an x-ray diffractometer. Calculated c-axis lattice parameters of the BST films exhibit a strong lattice distortion, which was not observed in ceramic BST at room temperature. This lattice distortion of BST has been attributed to strains caused by lattice constant difference between film and substrate, oxygen vacancies in BST film, and thermal expansion difference between film and substrate. Ferroelectric properties at 10 GHz have been measured using a HP 8510C vector network analyzer. Dielectric properties, capacitance tunability and quality factor, of the interdigitaed capacitors fabricated on BST films were calculated from the measured s-parameters. Two distinct behaviors in structural, opitical, and microwave properties of BST films were observed; below and above 200 mTorr of oxygen pressure in the deposition chmber.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제54권1호
• /
• pp.13-17
• /
• 2005

The Pb(Zr/sub 0.52/Ti/sub 0.48/)O₃/(Ba/sub 0.6/Sr/sub 0.4/)TiO₃[PZT/BST] heterolayered thin films were deposited on Pt/Ti/SiO₂/Si substrates by using the RF sputtering method with different RF power. The PZT/BST heterolayered thin films had the tetragonal structure of the PZT phase and BST phase. Increasing the RF power. the intensity of the PZT (100), (110) peaks and BST (111) peaks were decreased and the intensity of the BST (100), (110) peaks were increased. The thickness ratio of the top layered BST thin film and the bottom layered PZT thin film was 2 to1. The atomic concentration of the Ba, Sr, Pb. Zr, Ti atoms were constant in the PZT thin films and BST thin films, respectively. The Pt atom was diffused to the PZT region in the PZT/BST heterolayered thin films deposited at condition of 60[W] RF power. Increasing the frequency, dielectric constant and loss of the PZT/BST heterolayered thin films were decreased. The dielectric constant and loss of the PZT/BST heterolayered thin films deposited with RF power of 90[W] were 406 and 3%, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 센서 박막재료 반도체재료 기술교육
• /
• pp.103-106
• /
• 2002

The applicability of models based on fractal morphology to characterize $(Ba\;Sr)TiO_{3}$ thin film surfaces was investigated. The fractal morphology of coated barium strontium titan oxide thin film surfaces was described using fractal dimension from scanning electro microscopy image. The $(Ba\;Sr)TiO_{3}$ coating were deposited on silicon wafers using $(Ba\;Sr)TiO_{3}$ solution and spin coater. BST solution was composited by mol ratio, and then spin-coated from 3 times to 5 times coating on $Pt/SiO_{2}/Si$ substrate. Qualitative thin film analysis was performed with scanning electro microscopy (SEM), and surfaces parameters such as average grain diameter, roughness exponent and fractal dimension were determined.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2002년도 춘계 학술발표강연 및 논문개요집
• /
• pp.60-60
• /
• 2002

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2001년도 춘계학술발표강연 및 논문개요집
• /
• pp.32-32
• /
• 2001

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1995년도 추계 학술발표 강연 및 논문개요집
• /
• pp.95-95
• /
• 1995