• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.515-519
• /
• 2022

In this paper, we propose the development of a high-sensitivity entry-level nuclide analysis module. The proposed measurement sensor module consists of an electronic driving circuit for nuclide analysis resolution, prototype production with nuclide analysis function, and GUI development applied to prototypes. The electronic part driving circuit for nuclide analysis resolution is divided into nuclide analysis resolution process by the electronic part driving circuit block diagram, MCU circuit design used for radiation measurement, and PC program design for Spectrum acquisition. Prototyping with nuclide analysis function is made by adding a 128×128 pixel OLED display, three buttons for operation, a Li-ion battery, and a USB-C type port for charging the battery. The GUI development department applied to the prototype develops the screen composition such as the current time, elapsed measurement time, total count, and nuclide Spectrum. To evaluate the performance of the proposed measurement sensor module, an expert witness test was conducted. As a result of the test, it was confirmed that the calculated result by applying the resolution formula to the Spectrum (FWHM@662keV) obtained using the Cs-137 standard source in the nuclide analysis device had a resolution of 17.77%. Therefore, it was confirmed that the nuclide analysis resolution method proposed in this paper produces improved performance while being cheaper than the existing commercial nuclide analysis module.

• Journal of Radiopharmaceuticals and Molecular Probes
• /
• v.7 no.2
• /
• pp.119-125
• /
• 2021

⁸²Sr for ⁸²Rb generator was produced through the irradiation of the proton beam on the ^nat.RbCI target at the target irradiation facility installed at the end of the Rl-dedicated beamline of the 100 MeV proton linear accelerator of KOMAC (Korea Multi-purpose Accelerator Complex). The average current of the proton beam was 1.2 µA for irradiation time of 150 min. For the separation and purification of the ⁸²Sr from ^nat.RbCI irradiated, Chelex-100 resin was used. The activities of ⁸²Sr in the irradiated ^nat.RbCI target solution and after purification were 45.29 µCi and 43.4 µCi, respectively. The separation and purification yield was 95.8%. As an adsorbent to be filled in the generator for ⁸²Sr adsorption hydrous tin oxide was selected. The adsorption yield of ⁸²Sr into the generator adsorbent was > 99 %, and the total amount of ⁸²Sr adsorbed to the generator was 21.6 µCi as of the day of the ⁸²Rb elution experiment. When the elution amount was 22 mL, the maximum⁸²Rb elution yield was 93.3%, and the elution yield increased as the flow rate increased. After the eluted ⁸²Rb was filled in the correction phantom of the small PET for animals, a PET image was taken. The image scan time was set to 5 min, and the phantom PET image was successfully obtained. As results of impurity analysis on eluted ⁸²Rb using ICP-MS, ^nat.Rb stable isotopes that compete in vivo of ⁸²Rb were identified as undetected levels and were determined to be No-Carrier-Added (NCA).

• Journal of the Korean Society of Radiology
• /
• v.4 no.1
• /
• pp.5-9
• /
• 2010

In recent, a digital x-ray detector attracted worldwide attention and there are many studies to commercialize. There are two methods in digital x-ray detector. This method is an Indirect method and Direct method. This study is to see the differences between the digital x-ray detector based on a-Se used in the existing indirect conversion method and an x-ray conversion material that has better SNR(Signal-to-noise ratio) and property than the a-Se. To solve the problem that is difficult to make a large area film using Screen-Print method, we used a Screen-Print method. In this study, we used a polyclystal $HgI_2$ as x-ray conversion material and a sample thickness is $150{\mu}m$ and an area is $3cm{\times}3cm$. ITO(Indium-Tin-Oxide) electrode was used as top electrode using a Magnetron Sputtering System and each area is $3cm{\times}3cm$, $2cm{\times}2cm$ and $1cm{\times}1cm$ and then we evaluated darkcurrent, sensitivity and SNR of the $HgI_2$ film are measured, then we evaluated the electrical properties. And we used a current integration mode when I-V test. This experiment shows that the sensitivity increases in accordance with the area of the electrode but the SNR is decreased because of the high darkcurrent. Through fabricating of various thicknesses and optimal electrodes, we will optimize SNR in the future work.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.43 no.6 s.312
• /
• pp.28-35
• /
• 2006

Statistical models of shape variability based on active shape models (ASMs) have been successfully utilized to perform segmentation and recognition tasks in two-dimensional (2D) images. Three-dimensional (3D) model-based approaches are more promising than 2D approaches since they can bring in more realistic shape constraints for recognizing and delineating the object boundary. For 3D model-based approaches, however, building the 3D shape model from a training set of segmented instances of an object is a major challenge and currently it remains an open problem in building the 3D shape model, one essential step is to generate a point distribution model (PDM). Corresponding landmarks must be selected in all1 training shapes for generating PDM, and manual determination of landmark correspondences is very time-consuming, tedious, and error-prone. In this paper, we propose a novel automatic method for generating 3D statistical shape models. Given a set of training 3D shapes, we generate a 3D model by 1) building the mean shape fro]n the distance transform of the training shapes, 2) utilizing a tetrahedron method for automatically selecting landmarks on the mean shape, and 3) subsequently propagating these landmarks to each training shape via a distance labeling method. In this paper, we investigate the accuracy and compactness of the 3D model for the human liver built from 50 segmented individual CT data sets. The proposed method is very general without such assumptions and can be applied to other data sets.

• Natural Product Sciences
• /
• v.13 no.3
• /
• pp.199-206
• /
• 2007

Antioxidant activity of 70% aqueous ethanolic extract of leaves of Justicia gendarussa (EJ) was evaluated. EJ was prepared by cold maceration method. The antioxidant potency of EJ was investigated employing various established in vitro systems, such as DPPH radical scavenging, nitric oxide (NO) scavenging, ${\beta}-carotene$ linoleic acid module system (${\beta}$ CLAMS), hydroxyl (OH) radical scavenging, anti lipid peroxidation. $IC_{50}$ values were determined in each experiment. Also, ferric ion reduction capacity of extracts in presence and absence of chelating agent (EDTA) and total antioxidant capacity were determined. Preliminary phytochemical investigation was carried out to know the nature of constituents present in the leaves and correlate it with antioxidant activity. Further total phenolic content was determined in EJ. $IC_{50}$ values of EJ were 123.09 ${\pm}$ 3.01, 643.0 ${\pm}$ 61.10, 132.3 ${\pm}$ 6.03, 68.5 ${\pm}$ 11.5 and 68.13 ${\pm}$ 1.38 ${\mu}g/mL$ in DPPH radical scavenging, NO scavenging, ${\beta}$ CLAMS, OH radical scavenging and anti lipid peroxidation activity respectively. In total antioxidant capacity assay, ascorbic acid equivalent value was found to be 205.56 ${\pm}$ 4.69 ${\mu}g/mg$ of extract. Total phenolic content was found to be 43.76 ${\pm}$ 4.27 ${\mu}g$ equivalent of gallic acid per mg of extract. Phytochemical investigation reveals the presence of flavonoids. The results indicate that EJ possess antioxidant activity and flavonoids are responsible for this activity.

• Journal of Korean Society for Atmospheric Environment
• /
• v.16 no.E
• /
• pp.19-27
• /
• 2000

Particle Induced X-ray Emission (PIXE) and Elemental Analysis Syztem (EAS) were applied to the investiga-tion of the Characteristics and sources of wintertime atmospheric aerosols in Seoul. Atmospheric aerosols were collected by both fine and coarse fractions using a two-stage filter pack sampler from Kon-Kuk university during the winter season of 1999. PIXE was applied to the analysis of the middle and heavy elements with atomic numbers greater than 14(Si) and EAS was applied to the measurement of the light elements such as H, C and N. The fact that 64.2% of mass of fine particles in Seoul consists of the light elements (N, C , and H) suggests that the measurement of light elements is extremely important. The average mass concentration is Seoul was 38.6$\mu\textrm{g}$m(sup)-3. Elements such as Ca, Fe, Mg, and Ti appeared to have very low Fine/Coarse ratios(0.1∼0.4), whereas che-mical components related to anthropogenic sources such as Br, V, Pb, and Zn were observed to accumulate in the fine fraction. In the Asian Dust Storm(ADS) event, the concentation of soil components increased dramatically. Reconstruction of the fine mass concentrations estimated by a newly revised simple model was fairly in good agreement with the measured ones. Source identification was attempted using the enrichment factor and Pearsons coefficient of correlation. The typical elements derived from each source could be classified by this method.

• BMB Reports
• /
• v.40 no.5
• /
• pp.832-838
• /
• 2007

A novel inhibitory protein against blood coagulation factor Va (FVa) was purified from muscle protein of granulated ark (Tegillarca granosa, order Arcoida, marine bivalvia) by consecutive FPLC method using anion exchange and gel permeation chromatography. In the results of ESI-QTOF tandem mass analysis and database research, it was revealed that the purified T. granosa anticoagulant protein (TGAP) has 7.7 kDa of molecular mass and its partial sequence, HTHLQRAPHPNALGYHGK, has a high identity (64%) with serine/threonine kinase derived from Rhodopirellula baltica (order Planctomycetales, marine bacteria). TGAP could potently prolong thrombin time (TT), corresponding to inhibition of thrombin (FIIa) formation. Specific factor inhibitory assay showed that TGAP inhibits FVa among the major components of prothrombinase complex. In vitro assay for direct-binding affinity using surface plasmon resonance (SPR) spectrometer indicated that TGAP could be directly bound with FVa. In addition, the binding affinity of FVa to FII was decreased by addition of TGAP in dose-dependant manner ($IC_{50}$ value = 77.9 nM). These results illustrated that TGAP might interact with a heavy chain of FVa ($FVa_H$) bound to FII in prothrombin complex. The present study elucidated that non-cytotoxic T. granosa anticoagulant protein (TGAP) bound to FVa can prolong blood coagulation time by inhibiting conversion of FII to FIIa in blood coagulation cascade. In addition, TGAP did not significantly (P < 0.05) show fibrinolytic activity and cytotoxicity on venous endothelial cell line (ECV 304).

• Journal of Korean Academy of Nursing
• /
• v.36 no.7
• /
• pp.1232-1241
• /
• 2006

Purpose: The purpose of this study was to examine the effects of cerebral ischemia on Type I(soleus) and Type II(plantaris, gastrocnemius) muscles, and to determine the effects of isometric contraction training by electro- stimulation on Type I and II muscles in cerebral ischemia model rats. Method: Twenty-five male Sprague-Dawley rats were randomly divided into four groups: ST(stroke), STES(stroke+electrostimulation), SH(sham) and SHES (sham+electrostimulation). The ST and STES groups received a transient right middle cerebral artery occlusion operation. The SH and SHES groups received a sham operation. The STES and SHES groups had daily isometric contraction training by electrostimulation(100Hz, 45mA, 7.5V) on hindlimb muscles for 7days. Result: Plantaris and gastrocenmius muscle weight, myofibrillar protein contents of soleus and gastrocnemius, and the muscle fiber cross-sectional area of gastrocnemius in the ST group significantly decreased compared with the SH group. Soleus, plantaris, gastrocnemius muscle weight, myofibrillar protein contents of soleus and gastrocnemius, and the Type I muscle fiber cross-sectional area of soleus and the Type II muscle fiber cross-sectional area of gastrocnemius in the STES group significantly increased compared with the 57 group. Conclusion: Hindlimb muscle atrophy occurs after acute stroke and isometric contraction training by electrostimulation during early stages of a stroke attenuates muscle atrophy of Type I and Type II muscles.

• Current Photovoltaic Research
• /
• v.2 no.1
• /
• pp.1-7
• /
• 2014

We developed a method of growing thin Si film at $600^{\circ}C$ by hot wire CVD using a very thin large-grained poly-Si seed layer for thin-film Si solar cells. The seed layer was prepared by crystallizing an amorphous Si film by vapor-induced crystallization using $AlCl_3$ vapor. The average grain size of the p-type epitaxial Si layer was about $20{\mu}m$ and crystallographic defects in the epitaxial layer were mainly low-angle grain boundaries and coincident-site lattice boundaries, which are special boundaries with less electrical activity. Moreover, with a decreasing in-situ boron doping time, the mis-orientation angle between grain boundaries and in-grain defects in epitaxial Si decreased. Due to fewer defects, the epitaxial Si film was high quality evidenced from Raman and TEM analysis. The highest mobility of $360cm^2/V{\cdot}s$ was achieved by decreasing the in-situ boron doping time. The performance of our preliminary thin-film solar cells with a single-side HIT structure and $CoSi_2$ back contact was poor. However, the result showed that the epitaxial Si film has considerable potential for improved performance with a reduced boron doping concentration.

• Steel and Composite Structures
• /
• v.21 no.1
• /
• pp.1-36
• /
• 2016

In the present study, the nonlinear magneto-electro-mechanical free vibration behavior of rectangular double-bonded sandwich microbeams based on the modified strain gradient theory (MSGT) is investigated. It is noted that the top and bottom sandwich microbeams are considered with boron nitride nanotube reinforced composite face sheets (BNNTRC-SB) with electrical properties and carbon nanotube reinforced composite face sheets (CNTRC-SB) with magnetic fields, respectively, and also the homogenous core is used for both sandwich beams. The connections of every sandwich beam with its surrounding medium and also between them have been carried out by considering Pasternak foundations. To take size effect into account, the MSGT is introduced into the classical Timoshenko beam theory (CT) to develop a size-dependent beam model containing three additional material length scale parameters. For the CNTRC and BNNTRC face sheets of sandwich microbeams, uniform distribution (UD) and functionally graded (FG) distribution patterns of CNTs or BNNTs in four cases FG-X, FG-O, FG-A, and FG-V are employed. It is assumed that the material properties of face sheets for both sandwich beams are varied in the thickness direction and estimated through the extended rule of mixture. On the basis of the Hamilton's principle, the size-dependent nonlinear governing differential equations of motion and associated boundary conditions are derived and then discretized by using generalized differential quadrature method (GDQM). A detailed parametric study is presented to indicate the influences of electric and magnetic fields, slenderness ratio, thickness ratio of both sandwich microbeams, thickness ratio of every sandwich microbeam, dimensionless three material length scale parameters, Winkler spring modulus and various distribution types of face sheets on the first two natural frequencies of double-bonded sandwich microbeams. Furthermore, a comparison between the various beam models on the basis of the CT, modified couple stress theory (MCST), and MSGT is performed. It is illustrated that the thickness ratio of sandwich microbeams plays an important role in the vibrational behavior of the double-bonded sandwich microstructures. Meanwhile, it is concluded that by increasing H/lm, the values of first two natural frequencies tend to decrease for all amounts of the Winkler spring modulus.