• Proceedings of the Korean Vacuum Society Conference
• /
• 2001.07a
• /
• pp.50-50
• /
• 2001

• Proceedings of the Korean Vacuum Society Conference
• /
• 2002.02a
• /
• pp.117-117
• /
• 2002

• Journal of the Korean Magnetics Society
• /
• v.14 no.5
• /
• pp.196-200
• /
• 2004

In order to improve dendritic formation of Nd$_2$Fe$\_$14/B phase in the strip-cast Nd-Fe-B alloys that are frequently used for production of high energy sintered magnets, effect of small substitutional additives such as Cu (0.3～1.0 at. %) and Co (0.5～1.5 at.%) on the phase formation and microstructures of the strip-cast alloys based on Nd$\_$14/Fe$\_$80/B$\_$6/ were investigated. As the amount of Cu addition increased, formation of Nd$_2$Fe$\_$14/B dendrites along the direction normal to the strip surface was suppressed with the reduction of the strip thickness mainly due to the increase of fluidity of the melt. However, both the dendrites and their <001> preferred orientation along the direction normal to the strip surface were improved with the increase of the strip thickness as the amount of Co addition increased. The dendrites became finer after small amount of Cu or Co was added. While small copper additions tended to stabilize the formation of primary Fe, small cobalt additions suppressed it. When small amount of Zr was added, however, the dendrite structures were totally collapsed with excessive grain growth of Nd$_2$Fe$\_$14/B.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.335-335
• /
• 2010

$SiO_2$, $B_2O_3$, $Al_2O_3$, CaO, MgO, $Na_2O$, $ZrO_2$, $Bi_2O_3$를 이용하여 성질이 다른 두 종류의 무연계 프릿트를 제조하여 특성을 표준화 하였고, 이들 무연계 프릿트를 이용하여 Ag계 도체 및 $RuO_2$계 저항페이스트롤 제조하여 특성에 미치는 프릿트 조성의 영향을 연구하였다. $B_2O_3$를 첨가하여 퍼짐특성이 큰 프릿트의 경우 더 우수한 페이스트 특성을 나타내었다.

• Electrical & Electronic Materials
• /
• v.11 no.11
• /
• pp.9-17
• /
• 1998

The dependence of the ionic conductivity on the B-site ion substitution in (Li0.5La0.5)Ti1-xMxO3 (M=Sn, Zr, Mn, Ge) system has been studied. Same valence state and various electronic configuration and ionic radius of Sn4+, Zr4+, Mn4+ and Ge4+(4d10(0.69$\AA$), 4p6(0.72$\AA$), 3d10(0.54$\AA$) and 3d3(0.54$\AA$), respectively) induced the various crystallographic variaton with substitutions. So it was possibleto investigate the crystallographic factor which influence the ionic conduction by observing the dependence of the conductivity on the crystallographic factor which influence the ionic conduction by observing the dependence of the conductivity on the crystallographic variations. We found that the conductivity increased with decreasing the radii of B-site ions or vice versa and octahedron distortion disturb the ion conduction. The reason for this reciprocal proportion of conductivity on the radius of B-site ions has been examined on the base of the interatomic bond strength change due to the cation substitutions. The results were good in agreement with the experimental results. Therefore it could be concluded that the interatomic bond strength change due to the cation substitutions may be the one of major factors influencing the lithium ion conductivity in perovskite(Li0.5La0.5) TiO3system.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.242-244
• /
• 1987

Using the energy trapping theory and the acoustic coupling theory. the Bandpass filter(center frequency = 10.7 MHz) of the fundamental thickness mode was made from the composition of $Pb_{0.96}Sr_{0.04}(Zr_{0.53}Ti_{0.47})O_3$+ 1wt% $Fe_2O_3$. Also, in the double mode monolithic filter, It was observed that as decreasing the size of the electrodes, or shortening the gap between two electrodes, the percent frequency separation was increased. Based on these. a 10.7 MHz uniwafer filter was made having the characteristics that bandwidth was 700 KHz and the percent frequency separation was 6 [dB] and selectivity was 29 [dB], end spurious response was 24 [dB] and insertion loss was 7 [dB].

• Journal of Technologic Dentistry
• /
• v.42 no.4
• /
• pp.326-333
• /
• 2020

Purpose: The purpose of this study was to evaluate the effects of various zirconia surface treatment methods on shear bond strength with resin cements. Methods: We prepared 120 cylindrical zirconia specimens (⌀10 mm×10 mm) using computer-aided design/computer-aided manufacturing (CAD/CAM). Each specimen was randomly subjected to one of four surface treatment conditions: (1) no treatment (control), (2) airborne-particle abrasion with 50 ㎛ of Al2O3 (A50), (3) airborne-particle abrasion with 125 ㎛ of Al2O3 (A125), and (4) ZrO2 slurry (ZA). Using a polytetrafluoroethylene mold (⌀6 mm×3 mm), we applied three resin cements (Panavia F 2.0, Super-Bond C&B, and Variolink N) to each specimen. The shear bond strength tests were performed in a universal testing machine. The surfaces of representative specimens of each group were evaluated under scanning electron microscope. We used one-way analysis of variance (ANOVA), two-way ANOVA, and post hoc Tukey honest significant difference test to analyze the data. Results: In the surface treatment method, the A50 group showed the highest bond strength, followed by A125, ZA, and control groups; however, no significant difference was observed between A50 and A125, A125 and ZA, and ZA and control (p>0.05). Among the resin cements, Super-Bond C&B showed the highest shear bond strength, followed by Panavia F 2.0 and Variolink N (p<0.05). Conclusion: Within the limitations of this study, application of airborne-particle abrasion and ZrO2 slurry improved the shear bond strength of resin cement on zirconia.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1995.06a
• /
• pp.151-151
• /
• 1995

Nitrogen implantation process has been applied for improvement of wear resistance of Z Zircaloy-4 fuel cladding materials. Nitrogen was implanted at 120 ke V to a total do range of 1xHP ions/cm2 to 8xlO17 ions/cm2 at various temperatures of 298"C to 676"C. The m microstructure changes by nitrogen implantation were analyzed by using TEM, XRD 뻐d A AES, cmd then wear behavior was evaluated by ball-on-disc wear testings at various loads a and sliding velocity under unlubricated condition. Nitrogen implantation produced ZrNx nitride above 4.37x1017 ions!cm2 as well as heavy d dislocations, which enhanced microhardness of the implanted surface of up to 900 Hk from 2 200 Hk of unimplanted substrate. Hardness was also found to be increased with increasing i implantation temperature and enhanced up to OOOHk at 620 "C. the wear resistance was g greatly improved with increasing total ion do않 as well as implantation temperature. The effective enhancement of wear resistance at high dose and tem야ratures is believed d due to significant hardening associated with high degree of precipitation of Zr nitrides and g generation of prismatic dislocation I$\infty$ps.infty$ps.

• The Journal of Korean Academy of Prosthodontics
• /
• v.59 no.2
• /
• pp.153-163
• /
• 2021

Purpose: The aim of this study was to evaluate the effects of four surface treatment methods to improve zirconia roughness and three types of resin cement on the shear bond strength (SBS). Materials and methods: A total of 120 zirconia blocks were randomly divided into four surface treatments: non-treatment (Control), airborne-particle abrasion (APA) with 50 ㎛ Al2O3 (APA50), APA with 125 ㎛ Al2O3 (APA125), and ZrO2 slurry (ZA). Three resin cements (Panavia F 2.0, Superbond C&B, and Variolink N) were applied to the surface-treated zirconia specimens. All specimens were subjected to SBS testing using a universal testing machine. The surface of the representative specimens of each group was observed by scanning electron microscope (SEM). SBS data were analyzed with oneway ANOVA, two-way ANOVA test and post-hoc Tukey HSD Test (α=.05). Results: In the surface treatment method, APA125, APA50, ZA, and Control showed high shear bond strength in order, but there was no significant difference between APA125 and APA50 (P>.05). Also, ZA showed significantly higher shear bond strength than Control (P<.05). In the resin cement type, Panavia F 2.0, Superbond C&B, and Variolink N showed significantly higher shear bond strength in order (P<.05). In SEM images, the zirconia surfaces of the APA50 and APA125 showed quite rough and irregular shapes, and the zirconia surface of the ZA was observed small irregular porosity and rough surfaces. Conclusion: APA and ZrO2 slurry were enhanced the surface roughness of zirconia, and Panavia F 2.0 containing MDP showed the highest shear bond strength with zirconia.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.321-322
• /
• 2007

In this thesis, the sintering properties and piezoelectric properties of $Pb[(Co_{0.5}W_{0.5})_{0.03}(Ni_{1/3}Nb_{2/3})_{0.07}(Zr_{0.52}Ti_{0.48})_{0.9}]O_3+0.5[wt%]MnO_2$ ceramics has been systematically investigated as a function of the sintering temperature after manufacturing the specimens with a general method. The lattice constant from the analysis of crystal structure showed that the pychlore structure was decreased with the increase of the sintering temperature. Density was decreased by increasing $B_2O_3$. TCFr was showed its minimum variation rate of 0.35~-0.52[%] in the sintered temperature 950[$^{\circ}C$], $B_2O_3$ 3[wt%]. The electromechanical coupling coefficient (Kp) showed its maximum of 31.116[%] in the sintered temperature 1050[$^{\circ}C$], and its minimum of 20.220[%] in the sintered temperature 1150[$^{\circ}C$].