• Textile Coloration and Finishing
• /
• v.25 no.3
• /
• pp.172-180
• /
• 2013

Aramid fibers are being used increasingly in a wide range of application due to low density, high specific strength, high modulus, and high thermal resistance. But owing to its special physical and chemical structures, it is sensitive to absorb the ultraviolet light which will degrade the fiber's useful mechanical properties and structure. In this paper, the sol-gel technique was used to improve the photo-stability of p-aramid fibers. $TiO_2$, modified $SiO_2$/$TiO_2$ sol were used as coating solutions. The influence of the such coatings on the photo-stability of p-aramid fiber was investigated by an accelerated photo-ageing method using xenon lamp. The photo-stability of p-aramid fiber showed obvious improvement after the modified silica binding coating. But the amorphous $TiO_2$ sol coatings showed a negative effect. After 144h light exposure, the modified silane binder-coated fibers showed less degradation in mechanical properties with the retained tensile strength greater than about 70% of the original value.

• Journal of the Korean Ceramic Society
• /
• v.34 no.8
• /
• pp.897-907
• /
• 1997

Thin films of Bi4-xSmxTi3O12(0$\leq$x$\leq$2) were prepared on Pt/Ti/SiO2/Si(100) at $700^{\circ}C$ using spin-coating with sols derived from Bi-Sm-Ti complex alkoxides. From X-ray diffraction analysis, it was observed that Sm-substituted phases resembled ferroelectric Bi4Ti3O12 in structure. Variations of their lattice parameters depending on the amount of Sm-substitution showed that an anomalous structural distortion might exist at x=1. The grain sizes of the thin films decreased from 0.115 ${\mu}{\textrm}{m}$ to 0.078${\mu}{\textrm}{m}$ with increasing the amount of Sm-substitution. The dielectric constants and the remanent polarizations of the thin films decreased with increasing the amount of the Sm-substitution, which were related to decrease of the stereo-active Bi3+ ion contributing to polarization. However, these values were exceptionally high at x=1, compared to those of the other substituted phases. Such an anomaly suggests that the phase of x=1 has 1:1 chemical ordering between Sm and Bi in structure. The thin films of all compositions except x=2 showed ferroelectricity. The thin film of x=2 was paraelectric, whose grains were too fine to exhibit ferroelectricity.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.05a
• /
• pp.248-254
• /
• 2002

The most controversial topics in plasma sprayed ceramic coating system are recently mechanical properties such as bond strength, cohesive strength, toughness and so on. Determination of bond strength of coatings is one of the most important problems. In the industry, the bond strength of coating system has been estimated by Pull-off test(ASTM standard C633-79). But, without a fixed jig and specimen, it is impossible to obtain the bond strength. Therefore, it is necessary to study the critical fracture load on interface of the coating by indentation test. Because the critical fracture load plays an important role in evaluating the bond strength for plasma sprayed ceramic coating system. So, we have estimated critical fracture load in plasma sprayed ceramic coating system, and it was shown that inverse relationship between the cross-section hardness of coating and the critical fracture load(Pc). In case of the high load(1kgf, 2kgf) in $Al_{2}O_{3}+13%TiO_{2}$, it was found that the critical point(Pco), which the coating was broken on.

• Journal of the Speleological Society of Korea
• /
• no.76
• /
• pp.61-66
• /
• 2006

The present report is the investigation of the effects of the HIP treatment on plasma-sprayed ceramic coating of $Al_2O_3$, $Al_2O_3-SiO_2$ on the metal substrate. These effects were characterized by phase identification, Vickers hardness measurement, and tensile test before and after HIPing.

• Nuclear Engineering and Technology
• /
• v.52 no.9
• /
• pp.2054-2063
• /
• 2020

The high-temperature oxidation behavior of ZrSi₂ used as a coating material for nuclear fuel cladding was investigated for developing accident-tolerant fuel cladding of light water reactors. Bulk ZrSi₂ samples were prepared by spark plasma sintering. In situ X-ray diffraction was conducted in air at 900, 1000, and 1100 ℃ for 20 h. The microstructures of the samples before and after oxidation were examined by scanning electron microscopy and transmission electron microscopy. The results showed that the oxide layer of zirconium silicide exhibited a layer-by-layer structure of crystalline ZrO₂ and amorphous SiO₂, and the high-temperature oxidation resistance was superior to that of Zircaloy-4 owing to the SiO₂ layer formed. ZrSi₂ was coated on the Zircaloy-4 tube surface using laser 3D printing, and the coated tube was oxidized for 2000 s at 1200 ℃ under a vapor/argon mixture atmosphere. The outer surface of the coated tube was hardly oxidized (10-30 ㎛), while the inner surface of the uncoated tube was significantly oxidized to approximately 300 ㎛.

• Journal of Welding and Joining
• /
• v.19 no.2
• /
• pp.221-227
• /
• 2001

Based on the principle of complementary energy, an analytical method is developed which focuses on the end effects for determining thermal stress distributions in a three-layered beam. This method gives the stress distributions which completely satisfy the stress-free boundary conditions. A numerical example is given in order to verify this method. The results show that the present analytical solutions have the values of stress in excellent agreement with the solutions derived by other investigators. Using this method, the effects of the thickness of bond coat on the thermal stresses of a typical sprayed thermal barrier coating, which consists of IN738LC substrate, MCrAIY bond coat and ZrO$_2$-8wt%Y$_2$O$_3$top coat, were investigated.

• The Journal of Korean Academy of Prosthodontics
• /
• v.45 no.5
• /
• pp.601-610
• /
• 2007

Statement of problem: The adhesion between titanium and ceramic is less optimal than conventional metal-ceramic bonding, due to reaction layer form on cast titanium surface during porcelain firing. Purpose: This study characterized the effect of titanium-ceramic adhesion after gold and TiN coating on cast and wrought titanium substrates. Material and method: Six groups of ASTM grade II commercially pure titanium and cast titanium specimens$(13mm{\times}13mm{\times}1mm)$ were prepared(n=8). The conventional Au-Pd-In alloy served as the control. All specimens were sandblasted with $110{\mu}m\;Al_2O_3$ particles and ultrasonically cleaned for 5min in deionized water and dried in air before porcelain firing. An ultra-low-fusing dental porcelain (Vita Titankeramik) was fused on titanium surfaces. Porcelain was debonded by a biaxial flexure test at a cross head speed of 0.25mm/min. The excellent titanium-ceramic adherence was exhibited by the presence of a dentin porcelain layer on the specimen surface after the biaxial flexure test. Area fraction of adherent porcelain (AFAP) was determined by SEM/EDS. Numerical results were statistically analyzed by one-way ANOVA and Student-Newman-Keuls test at ${\alpha}=0.05$. Results: The AFAP value of cast titanium was greatest in the group 2 with TiN coating, followed by group 1 with Au coating and the group 3 with $Al_2O_3$ sandblasting. Significant statistical difference was found between the group 1, 2 and the group 3 (p<.05). The AFAP value of wrought titanium was greatest in the group 5 with TiN coating, followed by the group 4 with Au coating and the group 6 with $Al_2O_3$ sandblasting. Conclusion: No significant difference was observed among the three groups (p>.05). The AFAP values of the cast titanium and the wrought titanium were similar. However the group treated with $Al_2O_3$ sandblasting showed significantly lower value (p<.05).

• Journal of the Korean Ceramic Society
• /
• v.39 no.1
• /
• pp.79-85
• /
• 2002

Plasma-sprayed Cr$_2$O$_3$-based coatings containing MoO$_3$were studied to gain a better understanding of the influence of MoO$_3$composition in the coatings on their tribological behaviour. A reciprocal type tribo-tester was employed to examine friction and wear behavior of the specimens at room temperature. The physical characteristics of worn surfaces were investigated by scanning electron microscopy and chemical composition of the coating surfaces was analyzed using a X-ray photoelectron spectrometer. The results showed that friction coefficient of the MoO$_3$-added coatings were lower than those without MoO$_3$addition. However pure Cr$_2$O$_3$coating showed the lowest wear loss at the self-mated test. The larger protecting layers were observed at the worn surface of plasma spray coated specimens with MoO$_3$addition. XPS analysis of the protecting layer indicated that MoO$_3$composition was dominantly formed at the surface. MoO$_3$composition in the protecting layer appears to be more favorable in reducing the friction.

• Korean Journal of Materials Research
• /
• v.27 no.12
• /
• pp.710-715
• /
• 2017

We synthesized YOF(yttirum oxyfluoride) powders through solid state reactions using $Y_2O_3$ and $YF_3$ as raw materials. The synthesis of crystalline YOF was started at $300^{\circ}C$ and completed at $500^{\circ}C$. The atmosphere during synthesis had a negligible effect on the synthesis of the YOF powder under the investigated temperature range. The particle size distribution of the YOF was nearly identical to that of the mixed $Y_2O_3$ and $YF_3$ powders. When the synthesized YOF powders were used as a raw material for the suspension plasma spray(SPS) coating, the crystalline phases of the coated layer consisted of YOF and $Y_2O_3$, indicating that oxidation or evaporation of YOF powders occurred during the coating process. Based on thermogravimetric analysis, the crystalline formation appeared to be affected by the evaporation of fluoride because of the high vapor pressure of the YOF material.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.42 no.3
• /
• pp.286-291
• /
• 1997

This experiment was carried out to improve seedling emergence and establishment in paddy rice sown into puddled soil. Rice seed were coated with CaO$_2$, KNO$_3$ and acid sulphate soil. When coated seeds with CaO$_2$, KNO$_3$ and acid sulphate soil were sown into puddled soil, soil redox potential was increased and the period of oxidizing was longer in KNO$_3$ than that of any other soils. pH was higher in control than that of coated seeds with CaO$_2$, KNO$_3$ and acid sulphate soil. It seems that the coated seeds oxidize soil locally, thus prohibit soil reduction. Seedling emergence was improved by seed coating materials. Emergence date was 8 days after seeding(DAS) in CaO$_2$, 14 DAS in acid sulphate soil, 21 DAS in KNO$_3$ coated seed and 20 DAS in uncoated seed, respectively. Emergence rate was highest in CaO$_2$ coated seed(80％) followed by acid sulphate soil coated seed(61％), while control(46％) and KNO$_3$(42％) were very poor. This result would be interpreted as the difference in oxidizing power among coating agents ; CaO$_2$ and acid sulphate soil may oxidize weakly and shortly while KNO$_3$ may oxidize soil strongly and persistantly. Our results suggested that local oxidizing around rice seed sown into puddled soil enhanced seedling emergence and also found a possibility to promote seedling emergence with acid soil.