• Journal of the Korean Ceramic Society
• /
• v.31 no.2
• /
• pp.177-184
• /
• 1994

AlN-BN ceramics with BN contents in the range of 10 to 40 wt% were prepared by hot pressing using no additive, or 3 wt%, Y2O3 or CaO, which are common densification aids for AlN. And their machinability, bend strength, and microstructures were investigated. Both the main and radial cutting forces decreased with increasing BN content in all three kinds of samples. For the BN contents of 30 wt% or above, the cutting forces were lower than that of a mild steel tested at a same condition. Especially in the case of main forces, the values were less than a quarter of that of a mild steel, indicating excellent machinability. Bend strength (when the tensile surfaces of specimens were perpendicular to the hot pressing direction) also decreased with BN content mainly due to the much lower Young's modulus of BN compared to AlN. With the composition of 30 wt% BN at which the AlN-BN ceramics started to show better machinability than a mild steel, the bend strength was 150 to 160 MPa, which is greater than that of machinable glass-ceramics of a mica system. With tensile surfaces parallel to the hot pressing direction, however, the bend strength obtained for the samples processed with the sintering acids showed low values (about 40 MPa), since most BN particles had such orientation that their cleavage planes (i.e., basal planes) were perpendicular to the pressing direction.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.3
• /
• pp.279-285
• /
• 2008

CNC (Carbon Nano Colloid) was used as an additive to the positive electrode to improve the discharge performance of sealed lead-acid batteries, The cathode active material ($PbO_2$) has a relatively low utility of less than 60 % compared with other kind of batteries, such as Ni-MH and Lithium ion, In this study, to overcome the above-mentioned problem we investigated the effects of CNC addition on the enhancement of electrical connection with not-utilized $PbO_2$ and resultantly electrical conductivity of electrode, We examined low rate discharge capacities, high rate discharge capacities and internal resistances of the batteries containing various amounts of CNC. From these results, we found out that the addition of CNC into the positive electrode made a significant improvement in high rate discharge capacity, We also suggested the optimum content of CNC material in positive electrode.

• Journal of Soil and Groundwater Environment
• /
• v.20 no.4
• /
• pp.1-7
• /
• 2015

The degradation of off-flavors which is 2-Methylisoborneol (2-MIB) and geosmin by means of ultrasound (US) and pulsed ultraviolet (PUV) irradiation and its combination with catalyst (wire mesh, wire mesh coated TiO₂, and TiO₂) and additive (H₂O₂) were investigated via water system. A combination treatment of TiO₂ and H₂O₂ heterogeneity with US (24 kHz) and PUV (6000 W) has shown improved results in destroying 2-MIB and geosmin, which may be attributed to chain reactions by the enhanced formation of hydroxyl radicals (·OH) through H₂O₂ dissociation and reactive oxide ions of TiO₂ addition. Rapid degradation of off-flavors occurred within 2 min under PUV process with H₂O₂ 100 mg/L (81.5% for 2- MIB; 79.3% for geosmin) and TiO₂ 100 mg/L (83.7% for 2-MIB; 79.8% for geosmin), while compared with H2O2 100 mg/L (58.4% for 2-MIB; 58.0% for geosmin) and TiO₂ 100 mg/L (59.2% for 2-MIB; 38.5% for geosmin) within 5 min under US process. Surprisingly, the emphasis was given on the comparison with the same injected energies between PUV and US on degradation efficiency. Based on the injected energy comparison, the US provided better degradation performance under equal input power of 200 kJ with H₂O₂ 100 mg/L, while compared with H₂O₂ 100 mg/L under PUV process. Our findings suggest that US can be more effective compared to PUV for the degradation of off-flavors in aspect of energy consumptions.

• Journal of the Korean Magnetics Society
• /
• v.15 no.5
• /
• pp.282-286
• /
• 2005

Ni-Cu-Zn ferrites were prepared by the co-precipitation and ferrite microwave absorbers on low temperature sintering were investigated in this work. The properties of its microwave absorbing and physical were analyzed into variations of Ni addition, calcination temperature, sintering temperature. From the analysis of X-ray diffraction patterns, we can see that all the particles have only a single phase spinel structure. In addition, the powders particle size distribution obtained the nano size. By increasing the Ni additive, the permeability of the powders was decreased and the loss factor increased at sintering temperature $1100^{\circ}C$. Also, we considered that it can used high frequency rage. We found that the $(Ni_{0.7}Cu_{0.2}Zn_{0.1}O)_{1.02}(Fe_{2}O_3)_{0.98}$ appeared microwave absorbing properties better than other composition.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1535-1537
• /
• 2003

Manganese oxide electrode was designed to improve electrical conductivity for dimensionally stable anode(DSA) using discreet variation (DV)-X${\alpha}$ method. It was calculated in DV-X${\alpha}$ method that the addition of nickel to manganese oxide reduce the energy band gap of manganese oxide electrode. Therefore, it is estimated that nickel in 3 additive elements of Ti, Ni and Sn is the best candidate to improve the electrical conductivity of manganese oxide. The anodically deposited manganese oxide which was produced in 0.2M $MnSO_4$ and 0.2M (Mn,Ni)$SO_4$ solution had $MnSO_4$ structure which was identified by XRD. The $MnSO_4$ films produced in both solutions over than 50mA/$cm^2$ of current density and long deposition time of 600sec showed low adhesion with Ti substrate.

• Journal of the Korean Electrochemical Society
• /
• v.4 no.4
• /
• pp.139-145
• /
• 2001

Various compositions of iron oxide based materials as a cathode of lithium secondary battery have been fabricated and tested with electrochemical method. A layered form of $LiFeO_2$ was synthesized by mixing and heating the initial materials of $FeCl_3\;6H_2O,\;LiOH$ and NaOH at low temperature. The effect of changing the precursors composition was investigated. As a result, when increasing the additive amount of NaOH, the capacity of the electrode is decreased but the performance and declining rate of capacity became smaller. $LiFeO_2$ synthesized with the weight ratio of $NaOH/FeCl_3/LiOH,\;2/1/7$ showed the largest capacity, but the discharging efficiency was sharply decreased after 30 cycles. Charge-discharge tests of lithium cells with $LiFeO_2$ cathode having the layer structure were performed. This cell showed the reversibility in the range of 1.5-4.5V of cell voltage. By using CPR method, chemical diffusion coefficients were measured in 1M $LiPF_6/EC/DEC$ solution. The value of chemical diffusion coefficient decreased with increasing the lithium content x, In 0.5$10^{-11}^cm^2/s$.

• Asian-Australasian Journal of Animal Sciences
• /
• v.15 no.9
• /
• pp.1232-1236
• /
• 2002

Direct and service sire genetic parameters for total number of pigs born (TNB), number of pigs born alive (NBA), total pig weight at birth (TWB), and average pig birth weight (ABW) were estimated by DF-REML under a multiple trait animal model. Data on 3,078 litters of the Yorkshire from Jan, 1975 to Dec, 1998 at National Livestock Research Institute were obtained. The animal model included fixed contemporary group effects and random additive direct, service sire, and residual effects. Additive genetic relationships among animals were included. A separate relationship matrix for service sires and their sire was also included. Additive direct heritability estimates for TNB, NBA, TWB, and ABW were 0.19, 0.18, 0.25 and 0.39, respectively. Service sire heritability estimates for TNB, NBA, TWB, and ABW were 0.02, 0.01, 0.02 and 0.01, respectively. The genetic and phenotypic correlations of TNB with NBA estimated in this study were 0.81 and 0.81, respectively, and the genetic and phenotypic correlations of TNB with TWB estimated were 0.82 and 0.76, respectively. Results indicate that service sires account for 1 to 2% of the total variation for TNB, NBA, TWB, and ABW. Further investigation is needed to determine whether the service sire effect is primarily genetic or environmental.

• Journal of the Korean Chemical Society
• /
• v.29 no.4
• /
• pp.390-396
• /
• 1985

The manganese was extracted from ferromanganese slag with 6N ammonium sulfate and purified with ammonium sulfide. The current efficiencies were substantially increased when small amounts of selenious acid is used as an additive. Stainless steel was used as cathodic electrode and lead (+1% Ag) as anodic electrode. The effects of several variables were investigated, and the optimum conditions were found to be; 40g/l Mn in electrolyte at pH 7.0 with 1$20g/l (NH_4)_2SO_4$, Cathode current density 60mA/cm$^2$, Current efficiency 90% and up at the temperature about $25^{\circ}C.$ The metal produced has been consistantly of high quality.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.288-291
• /
• 2001

It is very important to select suspension solution for forming electrophoretic deposited YBCO thick mm, because it is heavily affected to its superconducting properties. In this paper, high-temperature superconductor films of $YBa_{2}Cu_{3}O_{7-x}$ were fabricated by electrophoretic deposition (EPD) from alcohol-based suspension such as iso-propanol, iso-butanol, and their mixture. For the formation of YBCO dense and adherent coating on a silver wire by EPD, 1 % PEG(1000) 2 ml, as a additive for making their surface crack-free, was used for electrophoresis. As a results, the cracks were considerably decreased and the superconducting critical current density $(J_e)$ without/with PEG was $1200A/cm^2$ and $2020A/cm^2$, which films deposited in mix iso-propanol and iso-butanol suspension.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.288-291
• /
• 2001

It is very important to select suspension solution for forming electrophoretic deposited YBCO thick film, because it is heavily affected to its superconducting properties. In this paper, high-temperature superconductor films of YBa$_2$Cu$_3$$O_{7-x}$ were fabricated by electrophoretic deposition (EPD) from alcohol-based suspension such as iso-propanol, iso-butanol, and their mixture. For the formation of YBCO dense and adherent coating on a silver wire by EPD, 1% PEG(1000) 2 $m\ell$, as a additive for making their surface crack-free, was used for electrophoresis. As a results, the cracks were considerably decreased and the superconducting critical current density (J$_{c}$) without/with PEG was 1200 A/$\textrm{cm}^2$ and 2020 A/$\textrm{cm}^2$, which films deposited in mix ism-propanol and iso-butanol suspension.ion.