• Korean Journal of Materials Research
• /
• v.22 no.4
• /
• pp.202-206
• /
• 2012

$CoSi_2$ was formed through annealing of atomic layer deposition Co thin films. Co ALD was carried out using bis(N,N'-diisopropylacetamidinato) cobalt ($Co(iPr-AMD)_2$) as a precursor and $NH_3$ as a reactant; this reaction produced a highly conformal Co film with low resistivity ($50\;{\mu}{\Omega}cm$). To prevent oxygen contamination, $ex-situ$ sputtered Ti and $in-situ$ ALD Ru were used as capping layers, and the silicide formation prepared by rapid thermal annealing (RTA) was used for comparison. Ru ALD was carried out with (Dimethylcyclopendienyl)(Ethylcyclopentadienyl) Ruthenium ((DMPD)(EtCp)Ru) and $O_2$ as a precursor and reactant, respectively; the resulting material has good conformality of as much as 90% in structure of high aspect ratio. X-ray diffraction showed that $CoSi_2$ was in a poly-crystalline state and formed at over $800^{\circ}C$ of annealing temperature for both cases. To investigate the as-deposited and annealed sample with each capping layer, high resolution scanning transmission electron microscopy (STEM) was employed with electron energy loss spectroscopy (EELS). After annealing, in the case of the Ti capping layer, $CoSi_2$ about 40 nm thick was formed while the $SiO_x$ interlayer, which is the native oxide, became thinner due to oxygen scavenging property of Ti. Although Si diffusion toward the outside occurred in the Ru capping layer case, and the Ru layer was not as good as the sputtered Ti layer, in terms of the lack of scavenging oxygen, the Ru layer prepared by the ALD process, with high conformality, acted as a capping layer, resulting in the prevention of oxidation and the formation of $CoSi_2$.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.2
• /
• pp.100-104
• /
• 2008

Titanium sheet metal substrates used in thin film batteries were wet etched and their surface area was increased in order to increase the discharge capacity and power density of the batteries. To obtain a homogeneous etching pattern, we used a conventional photolithographic process. Homogeneous hemisphere-shaped wells with a diameter of approximately $40\;{\mu}m$ were formed on the surface of the Ti substrate using a photo-etching process with a $20\;{\mu}m{\times}20\;{\mu}m$ square patterned photo mask. All-solid-state thin film cells composed of a Li/Lithium phosphorous oxynitride (Lipon)/$LiCoO_2$ system were fabricated onto the wet etched substrate using a physical vapor deposition method and their performances were compared with those of the cells on a bare substrate. It was found that the discharge capacity of the cells fabricated on wet etched Ti substrate increased by ca. 25% compared to that of the cell fabricated on bare one. High discharge rate was also able to be obtained through the reduction in the internal resistance. However, the cells fabricated on the wet etched substrate exhibited a higher degradation rate with charge-discharge cycling due to the nonuniform step coverage of the thin films, while the cells on the bare substrate demonstrated a good cycling performance.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.5
• /
• pp.22-31
• /
• 1997

We have measured the optical properties, thickness, and energy band gap of the P $b_{1-x}$/100/L $a_{x}$100/ $Ti_{1-}$0.25x/100/ $O_{3}$ (PLT(x)) thin film prepared by the sol-gel method with varying the La concentration, x, fyom 15 nto 33 mol%. We have obtained the values from the tranmission spectrum and employed the envelope method in anayzing the spectrum. We have also performed the simulation of the transmission spectrum on the PC (personal computer) to verify the accuracy of the values 15 to 33mol%, the refractive index (at .lambda.=632.8nm) increases from 2.39 to 2.44. The extinction coefficient does not depend on the la concentration but mainly on te wavelength, and has the values between 0.2 and 0.5 at the wavelength shorter than 330nm and between 0.001 and 0.008 at the wavelength longer than 700nm. The energy band gap of the PLT (x) thin film has been obtained on the assumption of the direct band-to-band transition. It decreases from 3.28 to 3.17eV as the La concentration increases from 15 to 33 mol%. The thickness of the PLT(x) thin film has been also obtained in high accuracy by the envelope method..

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.335-340
• /
• 2000

We investigated the role of the capping layers in the formation of the cobalt silicide in Co/Si systems with TiN and Ti capping layers and without capping layers. The Co/Si interfacial reactions and the phase transformations by the rapid thermal annealing (RTA) processes were observed by sheet resistance measurements, XRD, SIMS and TEM analyses for the clean silicon substrate as well as for the chemically oxidized silicon substrate by $H_2SO_4$. We observed the retardation of the cobalt disilicide formation in the Co/Si system with Ti capping layers. In the case of Co/$SiO_2$/Si system, cobalt silicide was formed by the Co/Si reaction due to with the dissociation of the oxide layer by the Ti capping layers.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.5
• /
• pp.230-237
• /
• 2021

In this study, the influence of silicon contents on the microstructure, mechanical and tribological properties of Ti-Al-Si-N coatings were systematically investigated for application of cutting tools. The composition of the Ti-Al-Si-N coatings were controlled by different combinations of TiAl₂ and Ti₄Si composite target powers using an arc ion plating technique in a reactive gas mixture of high purity Ar and N₂ during depositions. Ti-Al-Si-N films were nanocomposite consisting of nanosized (Ti,Al,Si)N crystallites embedded in an amorphous Si₃N₄/SiO₂ matrix. The instrumental analyses revealed that the synthesized Ti-Al-Si-N film with Si content of 5.63 at.% was a nanocomposites consisting of nano-sized crystallites (5-7 nm in dia.) and a three dimensional thin layer of amorphous Si₃N₄ phase. The hardness of the Ti-Al-Si-N coatings also exhibited the maximum hardness value of about 47 GPa at a silicon content of ~5.63 at.% due to the microstructural change to a nanocomposite as well as the solid-solution hardening. The coating has a low friction coefficient of 0.55 at room temperature against an Inconel alloy ball. These excellent mechanical and tribological properties of the Ti-Al-Si-N coatings could help to improve the performance of machining and cutting tool applications.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.10
• /
• pp.821-825
• /
• 2009

Recently, transparent ZnO-based TFTs have attracted much attention for flexible displays because they can be fabricated on plastic substrates at low temperature. We report the fabrication and characteristics of ZnO TFTs having different channel thicknesses deposited at low temperature. The ZnO films were deposited as active channel layer on $Si_3N_4/Ti/SiO_2/p-Si$ substrates by RF magnetron sputtering at $100^{\circ}C$ without additional annealing. Also, the ZnO thin films deposited at oxygen partial pressures of 40%. ZnO TFTs using a bottom-gate configuration were investigated. The $Si_3N_4$ film was deposited as gate insulator by PE-CVD at $150^{\circ}C$. All Processes were processed below $150^{\circ}C$ which is optimal temperature for flexible display and were used dry etching method. The fabricated devices have different threshold slop, field effect mobility and subthreshold slop according to channel thickness. This characteristics are related with ZnO crystal properties analyzed with XRD and SPM. Electrical characteristics of 60 nm ZnO TFT (W/L = $20\;{\mu}m/20\;{\mu}m$) exhibited a field-effect mobility of $0.26\;cm^2/Vs$, a threshold voltage of 8.3 V, a subthreshold slop of 2.2 V/decade, and a $I_{ON/OFF}$ ratio of $7.5\times10^2$.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.3
• /
• pp.70-81
• /
• 1998

Fiber-Fabry-Perot (FFP) tunable filters, the essential component of WDM transmission, were designed, fabricated and characterized. Multi-layered thin film mirrors that consists of an optical collimater's corss section as a substrate and TiO$_{2}$SiO$_{2}$ alternating multi-layered films as a filter wer designed by means of the transfer matrix method. Fabricated mirrors showed the high reflectivity over around 98% as expected. After fabricating the tuneable filters using PZT, we measured FSR, FWHM, finesse , crosstalk and insertion loss, confirming that the built devices satisfied the optical filter's specifications required in the SEDM transmission systems.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.393-394
• /
• 2005

SBN25 박막을 씨앗층으로 사용하여 이온빔으로 증착한 SBN60/SBN25 다층박막에 대하여 결정화 및 배향 특성을 고찰하였다. 기판은 Pt(111)/TiO2/SiO2/Si(100) 웨이퍼 (Pt 두께 200nm)를 사용하였으며, 약 3000${\AA}$으로 증착한후 650~$750^{\circ}C$에서 후열처리를 하였다. 제작된 박막의 증착조건 및 열처리 조건에 따른 결정화특성 변화에 대하여 연구하였으며, SBN 박막을 MFM 구조의 박막커패시터로 제조하여 강유전특성을 측정하였다.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2008.12a
• /
• pp.6.2-6.2
• /
• 2008

• Korean Journal of Metals and Materials
• /
• v.50 no.7
• /
• pp.539-544
• /
• 2012

Thermal shock behavior of TiN-coated SUS 304 substrate was investigated using a laser ablation method. By short surface ablation with a pulse Nd-YAG laser, considerable surface crack and spalling were observed, whereas there were few oxidation phenomena, such as grain growth of TiN crystallites, nucleation and growth of $TiO_2$ crystallites, which were observed from the coatings quenched from $700^{\circ}C$ in a chamber. The oxygen concentration of the ablated coating surface with the pulse laser also had a lower value than that of the quenched coating surface by Auger electron spectroscopy and electron probe micro analysis. These results were attributed to the fact that the properties of the pulse laser method have a very short heating time and so the diffusion time for oxidation was insufficient. Consequently, it was verified that the laser thermal shock test provides a way to evaluate the influence of the thermal shock load reduced oxidation effect.