• Tribology and Lubricants
• /
• v.23 no.6
• /
• pp.261-265
• /
• 2007

Carbide-derived carbon coating has been synthesized by low temperature treatment of TiC disk with $H_2/Cl_2$ mixture gases. A variety of physical measurements indicated that Ti was extracted and carbon layer was formed by exposure of $Cl_2$ gas. The $I_D/I_G$ ratio increased with increasing $Cl_2$ gas concentration. Wear coefficient and frictional coefficient varied with $Cl_2$ gas concentration. When the $Cl_2$ gas concentration decreased to 3.3 vol%, the friction coefficient approach a minimum. The results showed that degree of graphite crystallinity and variation of porosity due to the $Cl_2$ gas content were responsible for different tribology performance.

• Journal of the Korean Chemical Society
• /
• v.49 no.3
• /
• pp.321-324
• /
• 2005

• Applied Chemistry for Engineering
• /
• v.7 no.4
• /
• pp.750-756
• /
• 1996

$TiO_2$ was dispersed in zeolite and glass filter by soaking them in isopropanol solution of titanium tetraisopropoxide and drying in the air, followed by calcination at $500^{\circ}C$. The analysis of chlorothalnoil was carried out by gas chromatograph with an electron capture detector. Chlorothalnoil was degraded photocatalytically over the matrix-supported $TiO_2$ efficiently and could be completely photodegraded after 3hrs. Production were 5.0ppm of $Cl^-$ for $TiO_2$ supported zeolite, 7.5ppm of $Cl^-$ for $TiO_2$ supported glass filter and 2.0ppm of $Cl^-$ for $TiO_2$ powder. But, $CN^-$ was lower than the detection limit irrespective of matrices.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.208-208
• /
• 2003

저온균일침전법(HPPLT)으로 제조된 TiO$_2$나노분말은 10$0^{\circ}C$이하의 온도에서 rutile상을 얻을 수 있다. 또한, rutile에서 anatase로의 상변화는 합성시간, 가열속도, 반응온도 그리고 음이온 첨가에 의해 일어난다고 보고되어졌지만, 금속양이온들에 의한 상변화는 알려진 바가 없다. 따라서, 다양한 양이온을 첨가하여 저온균일침전법에서 TiO$_2$의 상변화가 어떻게 일어나는지를 조사하였다. 출발원료인 TIC1$_4$를 사용하여 가수분해하여 0.67M의 TiOCl$_2$을 얻었다. 얻어진 TiOCl$_2$ 수용액에 각각 0.01M의 금속염화물(ZrOCl$_2$, NiCl$_2$, CuCl$_2$, FeCl$_3$, AlCl$_3$ 그리고 NbCl$_{5}$)을 첨가한 후 반응기에 넣고 10$0^{\circ}C$에서 4시간동안 가열하였다 가열한 후 얻어진 침전물에 NaOH 수용액을 이용하여 PH 7-8로 중화한 후 증류수로 Cl$^{-}$이온이 제거될 때까지 충분히 세척하였다. 세척된 침전물을 105$^{\circ}C$에서 24h동안 건조하여 분말을 얻었고, rutile에서 anatase로의 상변화특성을 관찰하기 위하여 XRD, SEM, TEM, ICP 분석을 실시하였다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.197-197
• /
• 2019

총인처리시설에서는 응집제를 주입하여 인이나 오염물질을 침전시켜 처리하고 있으며 PAC(poly aluminum chloride)나 $FeCl_3$, $Al_2(SO_4)_3$, 등 다양한 종류의 응집제가 사용되어지고 있다. 하지만 기존에 사용되어 지고 있는 알루미늄계열의 응집제는 처리수에 잔류이온이 존재하게 되어 인체에 축적돼 알츠하이머 병 등 신체질환을 유발할 수 있는 단점이 있다. 따라서 이러한 단점을 사전에 예방하기 위해 $TiCl_4$와 같은 티타늄계열 응집제에 대한 연구가 진행되고 있다. $TiCl_4$ 응집제는 인 제거에 효과적으로 적용할 수 있으며 수중에 잔류이온을 유발하지 않으며 Ti이온은 치과임플란트나 의료장비로 사용될 만큼 인체에 무해하다고 알려져 있다. 응집제 사용에 따라 생성된 응집슬러지의 처리방안에 있어서 기존 응집제의 경우 생성된 슬러지의 대부분은 하수슬러지 위탁처리업체를 통해 소각 및 매립, 재활용 되고 있으나, $TiCl_4$를 응집제로 사용할 경우 생성된 슬러지를 인발하여 건조 및 소성을 통해 이산화티타늄으로 재활용할 수 있어 슬러지를 친환경적으로 처리가 가능해 기존 슬러지 처리방안의 경제적, 환경적 부담을 줄일 수 있는 장점이 있다. 따라서 본 연구에서는 $TiCl_4$를 하수처리장 방류수에 주입하여 수중의 총인(T-P)을 처리한 후 생성된 슬러지를 인발하여 건조와 소성과정을 거쳐 이산화티타늄을 제조하였다. 방류수를 취수해 2.5mg/L의 초기 총인 농도를 가진 원수를 제조하였으며 제조된 원수에 $TiCl_4$를 0.6mL 주입하였을 때 99.93%의 총인제거효율을 얻을 수 있었다. 응집 실험 후 생성된 슬러지를 인발하여 건조 후 $300{\sim}1000^{\circ}C$의 각각 다른 온도조건에서 소성하여 이산화티타늄을 제조하였으며, SEM과 XRD를 통해 제조된 이산화티타늄의 표면특성과 결정성 분석을 실시하였다. 제조된 이산화티타늄은 $500{\sim}800^{\circ}C$에서는 아나타제, $900{\sim}1000^{\circ}C$에서는 루타일 결정구조가 나타났다. 또한, $TiCl_4$ 주입량에 따른 이산화티타늄의 최종 생산량과 제조 시 사용되는 건조로 및 소성로의 경제적 비용 등을 고려하여 이산화티타늄 1Ton을 제조하기 위해 필요한 단가를 산출하였다. 본 연구에서 제조된 이산화티타늄 1kg의 생산단가는 약 5,400원으로 나타났으며, 가장 많이 사용되는 P-25 광촉매 보다 저렴한 가격으로 제조 및 판매를 기대할 수 있다. 따라서 하수처리장에 적용 시 기존 응집제 보다 비싼 $TiCl_4$ 비용을 보완하고 친환경적인 슬러지 처리로 제조된 이산화티타늄의 유통 및 현장적용을 통해 경제적, 환경적으로 우수하다고 판단된다.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.2
• /
• pp.233-237
• /
• 2005

Cyclopentadiene compounds, 2-[CR'R(OMe)]-1,3-Me$_2C_5H_3$ (R, R' = 2,2'-biphenyl, 2) and 2-[CR'R(OSiMe$_3$)]-1,3-Me$_2C_5H_3$ (R, R' = 2,2'-biphenyl, 3; R = ph, R' = ph, 4; R = 2-naphthyl, R' = H, 5) are readily synthesized from 2-bromo-3-methoxy-1,3-dimethylcyclopentene (1). Reaction of the cyclopentadienes with Ti(NMe$_2$)$_4$ in toluene results in clean formation of the cyclopentadienyl tris(dimethylamido)titanium complexes, which are transformed to the trichloride complexes, 2-[CR'R(OMe)]-1,3-Me$_2C_5H_2$}TiCl$_3$ (R, R' = 2,2'-biphenyl, 6) and {2-[CR'R(OSiMe$_3$)]-1,3-Me$_2C_5H_2$}TiCl$_3$ (R, R' = 2,2'-biphenyl, 7; R = ph, R' = ph, 8; R = 2-naphthyl, R' = H, 9). Attempts to form C1-bridged Cp/oxido complexes by elimination of MeCl or Me$_3$SiCl were not successful. X-ray structures of 6, 7 and an intermediate complex {2-[Ph$_2$C(OSiMe$_3$)]-1,3-Me$_2C_5H_2$}TiCl$_2$(NMe$_2$) (10) were determined.

• Resources Recycling
• /
• v.29 no.3
• /
• pp.3-10
• /
• 2020

The chlorination kinetics of synthetic rutile prepared by selective chlorination of ilmenite with Cl₂ and CO gas mixture were studied in a fluidized bed. Th e effects of reaction temperature, reaction time, and the ratio of Cl₂ and CO partial pressure ($p_{Cl_2}/p_{CO}$) on the conversion rate of TiCl₄ were investigated. The conversion rate of TiC₄ was low under the high $p_{Cl_2}/p_{CO}$ conditions. Moreover, it was considered that the partial pressure of CO gas was more effective than that of Cl₂ gas when comparing the stoichiometric conversion rate and experimental results of high CO partial pressure. Considering the porous structure of particles, the rate controlling step of the chlorination of synthetic rutile was determined to be chemical reaction and the activation energy was calculated as 53.77 kJ/mol.

• Journal of Technologic Dentistry
• /
• v.28 no.1
• /
• pp.61-66
• /
• 2006

Titanium alloys have been used for dental materials due to it's very good biocompatibility. Ti-6Al-4V alloy instead of pure titanium is being widely used as biomaterials has some characteristics such as high fatigue strength, tensile strength and corrosion resistance. But it has been reported recently that the vanadium element expresses cytotoxicity and carcinogenicity and the aluminium element is related with dementia of Alzheimer type and neurotoxicity. The Ti-Nb alloys has designed and examined corrosion resistance. Ti-3wt.%Nb($\alpha$type), Ti-20wt.%Nb(${\alpha}+{\beta}$type) and Ti-40wt.%Nb($\beta$type) alloys were melted by vacuum arc furnace. The corrosion resistance of Ti alloys was evaluated by potentiodynamic polarization test in the solution of 0.9% NaCl and 5% HCl. The results can be summarized as follows: 1) For the corrosion test in the solution of 0.9% NaCl and 5% HCl, the corrosion behaviour of Ti-Nb alloys was similar to ASTM grade 2 CP Ti. 2) The corrosion resistance of Ti-20Nb alloy was better than that of CP-Ti, Ti-3Nb, Ti-40Nb alloy in 0.9% NaCl and 5% HCl, solutions.

• Journal of the Korean Ceramic Society
• /
• v.26 no.3
• /
• pp.371-380
• /
• 1989

The purpose of this experiment is to elucidate the reaction mechanism concerning to the formation of crystalline BaTiO3 synthesized by adding the pH control agent(KOH soln) in TiCl4 and BaCl2 solution (Wet direct synthetic method). In this expeirment, it is identified that the amorphous barium-titanate having Ba-O-Ti bonding is formed above pH5 due to the -OH- ion and Ti-gel is formed below pH5 due to the polymerization of metatitanic acid. The bonding of the amorphous Ba-O-Ti is identified by FT-IR spectrum and crystallization temperature is about 82$0^{\circ}C$. If the pH of the above system according to the -OH- ion concentration is above 13.8, the polymerized metatitanic acid will be depolymerized and produce [TiO3]2+ion and crystalline BaTiO3 is formed by reacting the produced [TiO3]-- ion with the active Ba++ ion.

• Corrosion Science and Technology
• /
• v.18 no.3
• /
• pp.110-116
• /
• 2019

Resistances to pitting corrosion of additive manufactured (AM) Ti-6Al-4V alloys in 0.6 M NaBr and 0.6 M NaCl aqueous solutions were compared using micro-droplet cell techniques. With respect to the pitting corrosion resistance, this study focused on two different types of halide anions in aqueous solutions, i.e. $Br^-$ and $Cl^-$. The differences between $Br^-$ and $Cl^-$ halide anions for breakdown on passive films of AM Ti-6Al-4V alloy were explained using Langmuir adsorption model with their equilibrium adsorption coefficients. The results of the analysis showed that the lower resistance to pitting potential of AM Ti-6Al-4V alloy in $Br^-$ aqueous solution was attributed to the higher equilibrium adsorption coefficient of Br-. In addition, micro-electrochemical test results showed that the pitting corrosion resistance of dark grains in additive manufactured Ti-6Al-4V alloy was lower as compared to that of bright grains due to the larger volume of ${\alpha}^{\prime}$ phase that caused the susceptibility to pit initiation.