• Journal of Powder Materials
• /
• v.6 no.1
• /
• pp.18-35
• /
• 1999

Phase equilibria in the system Si3N4-TiC-TiCxN1-x-C-N were determined by thermodynamic calculations (CALPHAD-method). The reaction peaction paths for Si3N4-TiC and SiC-TiC composites in the Ti-Si-C-n system were simulated at I bar N2-pressure and varying terpreatures. At a temperature of 1923 K two tie-triangles (TiC0.34N0.66+SiC+C and TiC0.13N0.87+SiC+Si3N4) and two 2-phase fieds (TiCxN1-x+SiC; 0.13

• Journal of the Microelectronics and Packaging Society
• /
• v.30 no.3
• /
• pp.111-118
• /
• 2023

MXene, a two-dimensional transition metal carbide or nitride, has recently attracted much attention as a lightweight and flexible electromagnetic shielding material due to its high electrical conductivity, good mechanical strength and thermal stability. In particular, the Ti-based MXene, Ti₃C₂T_x and Ti₂CT_x are reported to have the best electrical conductivity and electromagnetic shielding properties in the vast MXene family. Therefore, in this study, Ti₃C₂T_x and Ti₂CT_x films were prepared by vacuum filtration using Ti₃C₂T_x and Ti₂CT_x dispersions synthesized by interlayer metal etching and centrifugation of Ti₃AlC₂ and Ti₂AlC. The electrical conductivity and electromagnetic shielding efficiency of the films were measured after heat treatment at high temperature. Then, X-ray diffraction and photoelectron spectroscopy were performed to analyze the structural changes of Ti₃C₂T_x and Ti₂CT_x films after heat treatment and their effects on electromagnetic shielding. Based on the results of this study, we propose an optimal structure for an ultra-thin, lightweight, and high performance MXene-based electromagnetic shielding film for future applications in small and wearable electronics.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.9
• /
• pp.459-463
• /
• 2004

In this study, the (l-x)$TiTe_3O_{8}$-x$MgTiO_3$ ceramics were investigated to obtain the improved dielectric properties of a high temperature stability and a sintering temperature of less than $900^{\circ}C$ which was necessary for the LTCC. According to the X-ray diffraction patterns of the (l-x)$TiTe_3O_{8}$-x$MgTiO_3$(x=0∼1) ceramics, the columbite structure of $TiTe_3O_{8}$ and ilmenite structure of $MgTiO_3$ were coexisted. Increasing the $MgTiO_3$ mole ratio(x), the density and dielectric constant were decreased and temperature coefficient of resonant frequency was moved to the negative direction and the quality factor was increased. In the case of the 0.6$TiTe_3O_{8}$-0.4$MgTiO_3$ ceramics sintered at $830^{\circ}C$ for 3hr., the microwave dielectric properties were $\varepsilon_{\gamma}$=29.3, Q${\times}$$f_{\gamma}$=39.600GHz and $\tau$$_{f}$=+9.3ppm/$^{\circ}C$.

• Journal of Powder Materials
• /
• v.4 no.4
• /
• pp.291-297
• /
• 1997

Titanium cabide, TiC-x mole% Al composites, and functionally-graded materials (FGMs) of TiC-x mole% Al were synthesized by an electrothermal combustion (ETC) method. TiC-70 mole% Al composite was not ignited by indirect tungsten coil heating, but can be synthesized by an electrothermal combustion. The velocity of the combustion wave decreased with increasing addition of Al and increased with an increase in the applied electric field. Functionally-graded TiC-Al materials were made from reactant layers with compositions of Ti+C+x moles Al with x ranging from zero to 70 by an electrothermal combustion. In the FGM products a nearly linear change in composition in the graded region was observed in samples with 0$\leq$ x $\leq$ 70 with x being the mole% Al.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.7
• /
• pp.344-348
• /
• 2006

The effect of x on microwave dielectric properties of the $(1-x)Mg_4Ta_2O_9-x(TiO_2,\;CaTiO_3,\;SrTiO_3)$ ceramics for microwave components were investigated. All spcecimens prepared by the conventional mixed oxied method and sintered at $1450^{\circ}C$. Microwave dielectric properties of the $(1-x)Mg_4Ta_2O_9-xTiO_2$ ceramics were influenced by $MgTi_2O_5$ phase. Also the microwave dielectric properties of the $(1-x)Mg_4Ta_2O_9-x(TiO_2,\;CaTiO_3,\;SrTiO_3)$ ceramics were dominated with an addition of $CaTiO_3\;and\;SrTiO_3$. The dielectric constant $(\varepsilon_r)$, quality factor $(Q{\times}f_r)$ and temperature coefficient of the resonant frequency $(TCRF,\;\tau_f)$ of the $(1-x)Mg_4Ta_2O_9-x(TiO_2,\;CaTiO_3,\;SrTiO_3)$ ceramics were $12.96\sim70.98,\;5,132\sim186,410GHZ$ and $-35.82\sim+75.96ppm/^{\circ}C$, respectively, and depend on x and addition materials.

• Journal of the Korean Ceramic Society
• /
• v.34 no.9
• /
• pp.921-926
• /
• 1997

Two NbCx-C1-x/Y2O3/Ti sputter-coated Al2O3 substrates (L 5.5 cm$\times$W 0.5 cm) were diffusion bonded together using hot press method at 95$0^{\circ}C$ for 3 hours under 1 MPa of applied pressure. 4 points bending tests were used to evaluate the mechanical performance of these precracked laminate beams. Two types of mechanical responses were observed: crack penetration through the interface for x=0.75, 1 and crack deflection into an interface for x=0.25, 0.5. The Al2O3/NbCx-C1-x/Y2O3/Ti system suggested here has been proves to be effective for the thermokinetical stability and tailorability of the interfaces of Al2O3/Ti composites at 95$0^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.30 no.6
• /
• pp.441-448
• /
• 1993

The Ba1-xSrxTiO3 thin films deposited on ITO-coated glass substrate at 55$0^{\circ}C$ by rf magnetron sputtering method have individual preferential orientations as a function of composition (X=0, 0.25, 0.5, 0.75, 1) due to the stress relief interactions among the intrinsic compressive stress, thermal tensile stress adn extrinsic compressive stress (compressive stress in case of BaTiO3(Tc=12$0^{\circ}C$) and Ba0.75Sr0.25TiO3(Tc=57$^{\circ}C$)). This behavior also appears on the (BaSr)TiO3 thin films (X=0.5) deposited on ITO-coated glass substrate at deposition temperature between 35$0^{\circ}C$ and 55$0^{\circ}C$. The composition of Ba1-xSrxTiO3 thin films deposited on ITO-coated glass substrate at 55$0^{\circ}C$ is close to stoichiometry (1.009~1.089 in A/B ratio), but the compositional deviation from a stoichiometry is larger as SrTiO3 is added. The morphology of Ba1-xSrxTiO3 thin films is very similar for over all substrate temperatures, and the roughness due to the differences of cluster size is the smallest at X=0.25.

• Journal of Welding and Joining
• /
• v.26 no.1
• /
• pp.76-82
• /
• 2008

The effect of Nb addition on the precipitation and precipitate coarsening behavior was investigated in Ti and Ti + Nb steel weld HAZ. A dilatometer equipped with a He-quenching system was used to simulate the weld thermal cycle. Compared to $TiC_yN_{1-y}$ precipitate in a Ti containing steel, $Ti_xNb_{1-x}C_yN_{1-y}$ complex particle with addition of Nb is precipitated in a Ti + Nb containing steel. Meanwhile, precipitate coarsening occurred more easily in Ti + Nb steel, which may be because the high temperature stability of $Ti_xNb_{1-x}C_yN_{1-y}$ complex particle is deteriorated by the Nb addition.

• Korean Journal of Materials Research
• /
• v.32 no.5
• /
• pp.264-269
• /
• 2022

Ti₃C₂T_x MXene, which is a representative of the two-dimensional MXene family, is attracting considerable attention due to its remarkable physicochemical and mechanical properties. Despite its strengths, however, it is known to be vulnerable to oxidation. Many researchers have investigated the oxidation behaviors of the material, but most researches were conducted at high temperatures above 500 ℃ in an oxidation-retarding environment. In this research, we studied changes in the structural and electrical properties of Ti₃C₂T_x MXene induced by low-temperature heat treatments in ambient conditions. It was found that a number of TiO₂ particles were formed on the MXene surface when it was mildly heated to 200 ℃. Heating the material to higher temperatures, up to 400 ℃, the phase transformation of Ti₃C₂T_x MXene to TiO₂ was accelerated, resulting in a TiO₂/Ti₃C₂T_x hybrid. Consequently, the metallic nature of pure Ti₃C₂T_x MXene was transformed to semiconductive behavior upon heat-treating at ≥ 200 ℃. The results of this research clearly demonstrate that Ti₃C₂T_x MXene may be easily oxidized even at low temperatures once it is exposed to air.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.120-122
• /
• 2007

3성분계 $Ti-C_x-N_{1-x}$ 코팅막은 AIP(Arc Ion Plating)법에 의해 -25V의 바이어스와 $300^{\circ}C$의 분위기에서 스테인리스 스틸 기판 위에 증착시켰다. $Ti-C_x-N_{1-x}$ 코팅막 안의 탄소(carbon)는 유입가스 비 $CH_4/(CH_4+N_2)$를 변화시키며 합성하였다. 탄소(carbon)가 증가함으로써, $Ti-C_x-N_{1-x}$ 코팅막의 미세경도는 TiN 코팅막의 20 GPa로부터 x=0.52에서 최대 약 32 GPa로 측정되었다. 또한, 미세구조는 잔류응력과 관련 있으며 탄소 함량에 따라 평균마찰계수가 크게 감소하였다.