• Journal of Welding and Joining
• /
• v.23 no.6
• /
• pp.99-105
• /
• 2005

The mixing ratio effect of the GTD-111(base metal) powder and the GNI-3 (Ni-l4Cr-9.5Co-3.5Al-2.5B) powder on TLP(Transient Liquid Phase) bonding phenomena and mechanism was investigated. At the mixing ratio of the base metal powder under $50wt\%$, the base metal powders fully melted at the initial time and a large amount of the base metal near the bonded interlayer was dissolved by liquid inter metal. Liquid insert metal was eliminated by isothermal solidification which was controlled by the diffusion of B into the base metal. The solid phases in the bonded interlayer grew epitaxially from the base metal near the bonded interlayer inward the insert metal during the isothermal solidification. The number of grain boundaries farmed at the bonded interlayer corresponded with those of base metal. At the mixing ratio above $60wt\%$, the base metal powder melted only at the surface of the powder and the amount of the base metal dissolution was also less at the initial time. Nuclear of solids firmed not only from the base metal near the bonded interlayer but also from the remained base metal powder in the bonded interlayer. Finally, the polycrystal in the bonded interlayer was formed when the isothermal solidification finished. When the isothermal solidification was finished, the contents of the elements in the boned interlayer were approximately equal to those of the base metal. Cr-W borides and Cr-W-Ta-Ti borides formed in the base metal near the bonded interlayer. And these borides decreased with the increasing of holding time.

• Journal of Sensor Science and Technology
• /
• v.17 no.2
• /
• pp.127-132
• /
• 2008

The effect of $CeO_2$ as a sintering additive on the microstructure and the piezoelectric property of yPb$(Sb_{0.5}Nb_{0.5})O_3$-(1-y)Pb$(Zr_{0.52}Ti_{0.48})O_3$ ($0{\leq}y{\leq}0.1$, PSN-PZT) for a hypersonic sound speaker (HSS) application was investigated. The samples were sintered at $1250^{\circ}C$ for 2 h. The crystal structure and surface morphology of the samples were examined using XRD and FE-SEM, respectively. Study on the influence of $CeO_2$ additives on the dielectric and piezoelectric properties indicated that the $CeO_2$-added PSN-PZT system had a high piezoelectric properties. The optimized results of ${\varepsilon}_r=1209$, $K_p$=52% $d_{33}$=351(pC/N) and $Q_m$=1230.16 were obtained at 0.4 wt.% $CeO_2$-added PSN-PZT.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1283-1284
• /
• 2007

The barium strontium calcium titanate((Ba,Sr,Ca)$TiO_3$) powders prepared by the sol-gel method and $MnCO_3$ as acceptor were mixed oxide method. The microstructure was investigated with variation of $Pr_{2}O_{3}$ amount. The BSCT powder and $Pr_{2}O_{3}$ were mixed with organic vehicle(Ferro. B75001). BSCT thick films were fabricated by the screen-printing method on alumina substrates. The bottom electrode was Pt and upper electrode was Ag, respectively. All BSCT thick films were sintered at $1420^{\circ}C$, for 2h. The result of the differential thermal analysis(DTA), exothermic peak at around $654^{\circ}C$ due to the formation of the polycrystalline perovskite phase. In the X-ray diffraction(XRD) patterns, all BSCT thick films showed the typical perovskite polycrystalline structure and no pyrochlore phase was dbserved. The microstructure investigated by scanning electron microscope(SEM). Pore and grain size of BSCT thick films were decreased with increasing amount of $Pr_{2}O_{3}$ dopant. And the average grain size and thickness of BSCT thick films doped with 0.1 mol% $Pr_{2}O_{3}$ was $3.09{\mu}m$, $60{\mu}m$, respectively. The relative dielectric constant decreased and dielectric loss decreased with increasing amount of $Pr_{2}O_{3}$ dopant, the values of the BSCT thick films no doped with $Pr_{2}O_{3}$ were 7443 and 4 % at 1 kHz, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.567-567
• /
• 2012

Since the carbon nanotubes (CNTs) have extraordinary material properties, many researchers are trying to make a practical application in various fields [1]. In particular, the high surface area of CNTs was fascinated for nano-template on the catalytic system. $RuO_2$ coated CNTs are useful functional nano-composites in many applications, including super capacitors, fuel cells, biosensors, and field emitters. However, the research of interaction between CNTs and $RuO_2$ was not satisfied with various fields [2]. In this study, we will introduce the change of chemical and electrical state of $RuO_2$/CNTs at different temperatures by synchrotron radiation photoemission spectroscopy (SRPES). The t-MWCNTs used in this experiment were grown on the Ni/TiN/Si substrates by chemical vapor deposition. $RuO_2$ of 4-20 nm in thickness was deposited on the t-MWNTs by sputter. The SRPES measurements were carried out at the 4B1 beamline of the Pohang Accelerator Laboratory in Korea. The result of XPS measurement indicates that the deposited $RuO_2$ on the CNTs was reduced into pure Ru at above $300^{\circ}C$. And we confirmed that the effective work function of $RuO_2$/CNTs was decreased with increasing temperature.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.7-15
• /
• 2004

The ferroelectric SBT thin films as a material of capacitors for non-volatile FRAMs have some problems that its remanent polarization value is relatively low and the crystallization temperature is quite high abovc 80$0^{\circ}C$. Therefore, in this paper, SBTN solution with S $r_{0.9}$B $i_{2.1}$T $a_{1.8}$N $b_{0.2}$$O_{9}$ composition was synthesized by sol-gel method. Sr(O $C_2$ $H_{5}$)$_2$, Bi(TMHD)$_3$, Ta(O $C_2$ $H_{5}$)$_{5}$and Nb(O $C_2$ $H_{5}$)$_{5}$ were used as precursors, which were dissolved in 2-methoxyethanol. SBTN thin films with 200 nm thickness were deposited on Pt/Ti $O_2$/ $SiO_2$/Si substrates by spin-coating. UV-irradiation in a power of 200 W for 10 min and rapid thermal annealing in a 5-Torr-oxygen ambient at 76$0^{\circ}C$ for 60 sec were used to promote crystallization. The films were well crystallized and fine-grained after annealing at $650^{\circ}C$ in oxygen ambient. The electrical characteristics of 2Pr=11.94 $\mu$C/$\textrm{cm}^2$, Ps＋/Pr＋=0.54 at the applied voltage of 5 V were obtained for a 200-nm-thick SBTN films. This results show that 2Pr values of the UV irradiated and rapid thermal annealed SBTN thin films at the applied voltage of 5 V were about 57% higher than those of no additional processed SBTN thin films. thin films.lms.s.s.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.230-230
• /
• 2013

In amorphous or microcrystalline thin-film silicon solar cells, p-i-n structure is used instead of p/n junction structure as in wafer-based Si solar cells. Hence, these p-i-n structured solar cells inevitably consist of many interfaces and the cell efficiency critically depends on the effective control of these interfaces. In this study, in-situ plasma treatment process of the interfaces was developed to improve the efficiency of a-Si:H solar cell. The p-i-n cell was deposited using a single-chamber VHF-PECVD system, which was driven by a pulsed-RF generator at 80 MHz. In order to solve the cross-contamination problem of p-i layer, high RF power was applied without supplying SiH4 gas after p-layer deposition, which effectively cleaned B contamination inside chamber wall from p-layer deposition. In addition to the p-i interface control, various interface control techniques such as thin layer of TiO2 deposition to prevent H2 plasma reduction of FTO layer, multiple applications of thin i-layer deposition and H2 plasma treatment, H2 plasma treatment of i-layer prior to n-layer deposition, etc. were developed. In order to reduce the reflection at the air-glass interface, anti-reflective SiO2 coating was also adopted. The initial solar cell efficiency over 11% could be achieved for test cell area of 0.2 $cm^2$.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1938-1940
• /
• 2003

본 연구는 요소 센서 제작을 위한 과정으로서, 전기화학적 방법을 이용한 다공질 실리콘 구조 형성과, PDV(Physical Vapor Deposition) 법에 의한 백금 박막 코팅 및 전기화학적 전도성 고분자 코팅과 urease 고정화 단계를 고찰하고 감도 특성을 제시 하였다. 전극 기질로서 B을 도우핑한 p-type 실리콘웨이퍼를 사용하였고, HF:$C_2H_5OH:H_2O$=1:2:1의 부피비를 갖는 에칭 용액에서 5분간 -7 $mA/cm^2$의 일정 전류를 가하여 폭 2 ${\mu}m$, 깊이 10 ${\mu}m$의 다공질 실리콘(PS) 충을 형성하였다. 그 위에 200 ${\AA}$의 Ti 층을 underlayer로서 증착하고, 2000 ${\AA}$의 Pt를 중착하여 PS/Pt 박막 전극을 제작하고, 전도성 고분자로서 polypyrrole (PPy), 또는 poly(3-mehylthiophene) (P3MT)을 전기화학적으로 코팅한 후, urease(EC 3.5.1.5, type III, Jack Bean, Sigma)를 고정화 하였다. 고정화 시 전해질 수용액의 pH는 7.4로 하여 urease표면이 음전하를 갖도록 하고, 전극에 0.6 V (vs. SCE(Saturated Calomel Electrode))의 일정 전압을 가함으로써 urease가 전도성 고분자 표면에 전기적으로 흡착되도록 하였다. 이상의 방법으로 제작한 요소 센서의 감도는 PPy와 P3MT를 전자 전달 매질로 사용한 경우, 각각 8.44 ${\mu}A/mM{\cdot}cm^2$와 1.55 ${\mu}A/mM{\cdot}cm^2$의 감도를 보였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.2
• /
• pp.164-168
• /
• 2024

(La_0.7Sr_0.3)(Mn_1-xFe_x)O₃ (LSMFO) (x = 0.03, 0.06, 0.09, 0.12) precursor solution are prepared by sol-gel method. LSMFO thin films are fabricated by the spin-coating method on Pt/Ti/SiO₂/Si substrate, and the sintering temperature and time are 800℃ and 1 hr, respectively. The average thickness of the 6-times coated LSMFO films is about 181 to 190 nm and average grain size is about 18 to 20 nm. As the amount of Fe added in the LSMFO thin film increased, the resistivity decreased, and the TCR and B_25/65-value increased. Electrical resistivity, TCR and B_25/65-value of the (La_0.7Sr_0.3)(Mn_0.88Fe_0.12)O₃ thin film are 0.0136 mΩ-cm, 0.358%/℃, and 328 K at room temperature, respectively. The resistivity properties of LSMFO thin films matched well with Mott's VRH model.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.16 no.2
• /
• pp.127-132
• /
• 1996

This study was carried out to obtain good livestock production in comparison with 3 different pasture mixture (Control : TI = Potomac orchardgrass + Bastion perennial ryegrass + Fawn tall fescue + Regal white clover, T2 = Potomac orchardgrass + Bastion perennial ryegrass + Roa tall fescue + Regal white clover, T3 = Potomac orchardgrass + Bastion perennial ryegrass + Roa tall fescue + Tahora white clover) by grazing experiment used 45 dairy calves (about lOOkg liveweight) during the period from April to October, 1994 at the Isidole farm, Cheju. Daily liveweight gains of calves grazed during the experiment period were 331${\pm}$29, 352${\pm}$4, 356${\pm}$18g in treatment 1, 2 and 3 respectively, but did not get statistically significant difference. On compared the results with the period investigated, the period which was highest in daily liveweight gain was early grazing season b m May to June while the period shown to be lowest in daily liveweight gain was between late July and late August. Hehage intake rate did not get significant difference among treatments with results shown as 67${\pm}$1.2, 62${\pm}$5.1, 60${\pm}$9.6% in treatment 1, 2 and 3 respectively. And efficiency of conversation into animal product was high in treatment 2. It is considered that good results were not obtained in this study because tall fescue and white clover, important species in this trial did not cover the pasture well with slow establishment in 1st year after seeding.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.47 no.3
• /
• pp.167-173
• /
• 2002

This experiment was conducted to figure out the change of soil physical properties, rice growth and yield with the years of continuous cultivation in direct dry-seeding and no-tillage machine transplanting. Experiments were conducted at NHAES(National Honam Agricultural Experiment Station, RDA, Iksan, Cheon Buk Province, South Korea) with a rice variety "Dongjinbyeo" from 1995 to 2000. In no-tillage machine transplanting cultivation, organic matter in soil was higher than that on direct dry-seeding and was significantly high in topsoil. Problematic weed species were E. crus-galli B., A. keisak H., and L. japonica M. Plant height and tiller number m-2 were higher in common-tillage during the total growth duration. The highest weedy rice occurrence of 27.5% was observed in live years' continuous direct dry-seeding and followed by 6.2%, in four years', and 3.7%, in three years'. The highest yield reduction of 38% was observed in five years' continuous direct dry-seeding. The reduction may resulted from the competition between weedy rice and cultivated rice.