• Journal of the Korean Vacuum Society
• /
• v.9 no.1
• /
• pp.36-41
• /
• 2000

$SnO-2$ thin films for thin film secondary battery anode were deposited n glass substrate with stain-less steel collector and charge/discharge experiments were conducted to investigate feasibility of $SnO-2$ thin film as a new anode material. The as-deposited films were pure $SnO-2$ phase which is not related to deposition condition. The grain size on the surface of as-deposited films increased with increase of oxygen partial pressure. However, the grain size did not show any change above oxygen partial pressure of 80:20. The surface roughness of the as-deposited films increased after decreasing because of resputtering effect of oxygen negative ion in plasma. All films showed typical $SnO-2$ anode characteristics which has a side effect at the first cycle, which is not related to the deposition condition. The charge/discharge experiments of 200cycles indicated that capacity of $SnO-2$ films depended on oxygen contents and surface roughness. The cycle characteristics was determined by initial charge/discharge reaction. The $SnO-2$ film with low initial capacity showed more stable cycle characteristics than film with high initial capacity.

• Journal of the Korean Ceramic Society
• /
• v.36 no.5
• /
• pp.564-569
• /
• 1999

• Journal of the Korean Ceramic Society
• /
• v.33 no.4
• /
• pp.379-384
• /
• 1996

The H2S sensing mechanism of CuO-SnO2 was confirmed by analyzing the electrical-resistance variation with temperature under an H2S atmosphere. While the resistance of CuO-SnO2 thick film at N2+H2S atmosphere was almost invariant with change in temperature it increased with increasing temperature for air +H2S atmos-phere. This behavior was analyzed using an equation derived from a basic assumption based on the H2S sensing mechanism proposed before. the experimental results are sufficiently explained with the equation derived which showed that the H2S sensing mechanism was reasonable. The equation also gave a detailed analysis and physical meaning to the behavior of the resistance variation with change in H2S concentration.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.4
• /
• pp.135-139
• /
• 2009

$H_2S$ micro-gas sensors have been developed employing $SnO_2$:CuO composite thin films. The films were prepared by e-beam evaporation of Sn and Cu metals on silicon substrates, followed by oxidation at high temperatures. Results of various studies, such as scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) reveal that $SnO_2$ and CuO are mutually non-reactive. The CuO grains, which in turn reside in the inter-granular regions of $SnO_2$, inhibit grain growth of $SnO_2$ as well as forming a network of p-n junctions. The film showed more than a 90% relative resistance change when exposed to $H_2S$ gas at 1 ppm in air at an operating temperature of $350^{\circ}C$ and had a short response time of 8 sec.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.70-73
• /
• 2004

Two different $SnO_2$ nanomaterials(nanowires and nanobelts) were synthesized from the thermal evaporation of ball-milled $SnO_2$ powders at $1350^{\circ}C$ without the presence of any catalysts, and their structural properties are then investigated by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy. This investigation reveals that the $SnO_2$ nanowires are single-crystalline and their growth direction is parallel to the [100] direction, and that the $SnO_2$ nanobelts are single crystalline and their shape is zigzag. In addition, photoresponse of a single $SnO_2$ nanowire was performed with light above-gap energy, and different characteristics of photoresponse were obtained for the nanowire at ambient atmosphere and in vacuum.

• Advances in nano research
• /
• v.7 no.1
• /
• pp.13-24
• /
• 2019

Well-crystalline $SnO_2$ nanoparticles of 4-5 nm size with different In contents were synthesized by hydrothermal process at relatively low temperature and characterized by transmission electron microscopy (TEM), microRaman spectroscopy and photoluminescence (PL) spectroscopy. Indium incorporation in $SnO_2$ lattice is seen to cause a lattice expansion, increasing the average size of the nanoparticles. The fundamental phonon vibration modes of $SnO_2$ lattice suffer a broadening, and surface modes associated to particle size shift gradually with the increase of In content. Incorporation of In drastically enhances the PL emission of $SnO_2$ nanoparticles associated to deep electronic defect levels. Although In incorporation reduces the band gap energy of $SnO_2$ crystallites only marginally, it affects drastically their dye degradation behaviors under UV illumination. While the UV degradation of methylene blue (MB) by undoped $SnO_2$ nanoparticles occurs through the production of intermediate byproducts such as azure A, azure B, and azure C, direct mineralization of MB takes place for In-doped $SnO_2$ nanoparticles.

• Journal of the Korean institute of surface engineering
• /
• v.32 no.2
• /
• pp.125-133
• /
• 1999

Fluorine-doped $SnO_2$ thin films were deposited on soda-lime glass substrates by reactive DC magnetron sputtering method. Crystallinity as well as electrical and optical properties of $SnO_2$ : F thin film were investigated as the variations of deposition conditions such as substrate temperature, DC Power, $O_2$ gas pressure, $SF_6$ gas pressure. $SnO_2$ : F thin film deposited with 5% $SF_6$ gas pressure showed electrical resistivities of $2.5\times10^{-3}$cm with the average optical transparency (about 80%) These electrical and optical properties were found to be related to the crystallinity of $SnO_2$ : F thin films.

• Journal of Sensor Science and Technology
• /
• v.27 no.5
• /
• pp.345-351
• /
• 2018

We employed an unprecedented technique to synthesize porous $WO_3@SnO_2$ nanofibers exhibiting core-shell and fiber-in-tube configurations. Firstly, 2-methylimidazole was uniformly incorporated in as-spun nanofibers containing ammonium metatungstate hydrate and the sacrificial polymer (polyacrylonitrile). Secondly, the 2-methylimidazole on the surfaces of nanofibers was complexed with tin(II) chloride ($SnCl_2$) via simple impregnation of the as-spun nanofibers in ethanol containing tin(II) chloride dihydrate ($SnCl_2{\cdot}2H_2O$). The presence of vacant p-orbitals in tin (Sn) and the nucleophilic nitrogen on the imidazole ring allowed for the reaction between $SnCl_2$ and 2-methylimidazole, forming adducts on the surfaces of the as-spun nanofibers. The calcination of these nanofibers resulted in porous $WO_3@SnO_2$ nanofibers with a higher surface area ($55.3m^2{\cdot}g^{-1}$) and a better response to 1-5 ppm of acetone than pristine $SnO_2$ NFs synthesized using a similar method. An improved response to acetone was achieved upon functionalization of the $WO_3@SnO_2$ nanofibers with catalytic palladium nanoparticles. This work demonstrates the potential application of $WO_3@SnO_2$ nanofibers as sensing layers for chemiresistive sensory devices for the detection of acetone in exhaled breath.

• Journal of Powder Materials
• /
• v.14 no.5
• /
• pp.327-332
• /
• 2007

In a view point of environment, the advanced electric contact material without environmental load element such as cadmium has to be developed. Extensive studies have been carried out on $Ag-SnO_2$ electric contact material as a substitute of Ag-CdO contact materials. In the present study, powder metallurgy including compaction and sintering is introduced to solve the incomplete oxidation problems in manufacturing process of $Ag-SnO_2$ electrical contact material. The $Ag-SnO_2$ contact material, fabricated in this study, was actually set in an electric switchgear of which working voltage is 462V and current is between 25 and 40A, for the purpose of testing its performance. As a result, it exceeded the existing Ag-CdO contact materials in terminal-temperature ascent and main contact resistance.

• Korean Chemical Engineering Research
• /
• v.50 no.4
• /
• pp.723-728
• /
• 2012

The production of biodiesel by transesterification of soybean oil was performed on $MoO_3$, $SnO_2$ and $CeO_2$ mixed oxides. The catalysts were characterized using XRD and $NH_3$-TPD. $MoO_3$ showed the highest activity among the three metal oxides. When 7 wt% of catalysts was introduced into the reactants, the highest activity was obtained and the water added to reactant decreased the catalytic activity. $MoO_3$ and $SnO_2$ mixed with 50:50 showed the highest activity and $CeO_2$ added with 20% on the $MoO_3-SnO_2$ mixed oxide also showed the highest activity. The catalytic activity showed to have a good relationship with the amount of acid site of catalysts. When the waste soybean oil was used as a reactant, the conversion was decreased about 30%.